FASTENING TM FASTENING SYSTEMS SYSTEMS ENGINEERED ENGINEERED FOR FOR PERFORMANCE PERFORMANCE™
RIVET NUT INSERT CATALOG
AS9100, AS9100, ISO ISO 9001:2008 9001:2008 AND AND ISO/TS ISO/TS 16949:2009 16949:2009 CERTIFIED CERTIFIED
TABLE OF CONTENTS
PAGE 2-3
RIVET NUT Introduction
PAGE 4
FHK and FHL Large and Small Full Hex
PAGE 5
Imperial/Inch Body Style Rivet Nuts
PAGE 6
CAL Large Flange Knurled Body Thin Wall Series
PAGE 7
CAK Small Flange Knurled Body Thin Wall Series
PAGE 8
CAH Half Hex Body Large Flange Thin Wall Series
PAGE 9
CA Heavy Duty Rivet Nut Flat Head Series
PAGE 10
CAO Small Flange Smooth Body Thin Wall Series
PAGE 11
CFW/CAW Diamond Knurled 3600 Swaging Series
PAGE 12
CFT/CAT Knurled 3600 Swaging Series
PAGE 13
CPB Prebulbed Slotted Body Series
PAGE 14
CPN Straight Shank Slotted Body Series
PAGE 15
CFH & CFHD Full Hex Body Series
PAGE 16
Metric Body Style Rivet Nuts
PAGE 17
UPO Large Flange Metric Series
PAGE 18
UFO Countersunk Head and UKO Small Flange Metric Series
PAGE 19
HUPO & HUKO Large and Small Flange Hexagonal Metric Series
TABLE OF CONTENTS
PAGE 20
UPO RS/UFO RS Large and CS Knurled Metric Series
PAGE 21
UKO and HUKO Imperial Thread Series - Stainless Steel
PAGE 22
CLM & CKM Large and Small Flange Knurled Metric Body Series
PAGE 23-24 SHEREX CR/CRE Series, SHEREX LOCSERT® and SEAL 2 Systems PAGE 25-28 RIV-FLOAT® & RIV-FLOAT®-Short PAGE 29-31 LARGE Size Rivet Nut Family PAGE 32-35 NAS/MS Flat Head and Countersunk Head Styles PAGE 36-37 CAL and CAH Rivet Nut Kits PAGE 38
RIVET NUT Hand Tools
PAGE 39
RIVET NUT Pneumatic Spin - Spin Tools
PAGE 40-41 Hydro-Pneumatic FLEX-5 Tool PAGE 41
MS 100 RIVET NUT Tool
PAGE 42
Hydro-Pneumatic FLEX-18 Tool
PAGE 43
Value Propositions
PAGE 44
Testing Methods
PAGE 45-46 SHEREX Product Showcase PAGE 47
Engineering Guide
PAGE 48
SHEREX Decimal Equivalents and Drill Size Chart
PAGE 49
Additional SHEREX Services
ES
RIVET NUT INTRODUCTION RIVET NUT INTRODUCTION
Rivet Nut Introduction
rivet nut introduction
Blind Rivet Nuts provide load-bearing threads in thin sheet materials that too provide thin for a load-bearing tapped thread. Blind Rivet Blind Rivetare Nuts threads inNuts also are used when an applicationthat has are littletoo or no access the backside as they can be installed thin sheet materials thin for to a tapped from the front of are the work thread. Blind Rivet Nutsside also usedpiece. when an
application has little or no access to the backside as they can be installed from the front side of the work piece. Screw
Attached Component Base Material
Rivet Nut
Advantages of Rivet Nuts Rivet Nuts provide a strong thread in thin materials that cannot be tapped. Rivet Nuts can be installed from one side of the work piece, also known as a “Blind Application.” advantages of rivet nuts
Rivet Nuts work great when easy disassembly and reassembly of products is required. • Rivet Nuts provide a strong thread in thin materials that cannot be tapped.
Rivet nuts can be installed in many different kinds of material including steel, plastic and fiberglass. • Rivet Nuts can be installed from one side of the work piece, also known as a “Blind Application.”
Once Rivet Nuts are installed additional components with threaded fasteners can be attached. • Rivet Nuts are ideal when easy disassembly and reassembly of products is required.
Rivet Nuts do not need to be the base material. • Rivet Nuts can be welded installed to in many different kinds of material including steel, plastic and fiberglass. • Once Rivet are damaged installed, additional components with threaded fasteners can be attached. Prepainted material willNuts not be during the Rivet Nut installation process. • Rivet Nuts do not need to be welded to the base material. Rivet Nuts are available in many different styles & materials for many different kinds of applications.• Prepainted material will not be damaged during the Rivet Nut installation process. • Rivet Nuts are available in many different styles & materials for many different types of applications. Applications: Industries
2
Rivet nuts are used in a variety of industries: Automotive HVAC Aerospace
Ag/Construction Equipment
Lighting
Railways
Electronics
Sherex Fastening Solutions
Medical
Request Info 1-800-453-1692 • Phone: 866-474-3739 • Fax: 716-875-0358www.aboveboardelectronics.com • www.sherex.com • E-mail:
[email protected]
RIVET NUT INTRODUCTION RIVET NUT INTRODUCTION
applications: industries
Rivet nuts are used in a variety of industries: • Automotive • HVAC • Aerospace and Defense • Agricultural and Construction Equipment
• General Industrial • Electronics • Medical • Railways
• Heavy Truck (Class 8) • Solar
Examples are shown below.
Any manufacturing that uses thin materials
examples of rivet nut applications
Some Example Include:
Rivet Nut Rivet Nut
After Market Vehicle Retrofit - Tool Box
Vehicle Accessory - Pickup Side Rail
Rivet Nut
Rivet Nut
Appliance - Washer Tub Base
Agricultural – Class 10.9Strength Structural Agricultural – High Component Rivet Mounting Nut
Request Info Sherex Fastening Solutions
•
Phone: 866-474-3739
1-800-453-1692 www.aboveboardelectronics.com • Fax: 716-875-0358 • www.sherex.com • E-mail:
[email protected]
3 SHERES 1,91,111. SOLUTIOMS
FHK/ FHL series
FHK & FHL SERIES LARGE AND SMALL FLANGE FULL HEX SERIES FHK SERIES
FHL SERIES R
ma
HOLE SIZE
HOLE SIZE
• The FHK/FHL series provides increased spin out resistance over round body and half hex body rivet nuts.
L —1
WI WI
J = FIT
Il.
fhk
-
small flange unified thread (unit - inches) FHK - SMALL FLANGE UNIFIED THREAD (UNITS - INCHES)
SHEREX Part Number Inch - Steel SHEREX Part Number FHK2-2520-138 Inch - Steel FHK2-2520-236 FHK2-2520-138 FHK2-2520-335 FHK2-2520-236 FHK2-3118-157 FHK2-2520-335 FHK2-3118-276 FHK2-3118-157 FHK2-3118-394 FHK2-3118-276 FHK2-3716-177 FHK2-3118-394 FHK2-3716-295 FHK2-3716-177 FHK2-3716-413 FHK2-3716-295 FHK2-5013-177 FHK2-3716-413 FHK2-5013-177
• Proven to meet Class 8 and Grade 5 thread strength.
Grip Range FHKSize - SMALL FLANGE Thread Min. Max. Grip Range Thread Size .039 .138 Min. Max. 1/4-20 UNC .138 .236 .039 .138 .236 .335 1/4-20 UNC .138 .236 .031 .157 .236 .335 5/16-18 UNC .157 .276 .031 .157 .276 .394 5/16-18 UNC .157 .276 .039 .177 .276 .394 3/8-16 UNC .177 .295 .039 .177 .295 .413 3/8-16 .177 .295 1/2-13 UNC .039 .177 .295 .413 1/2-13 UNC .039 .177
L
HD (A/F)
HT
D (A/F)
IL
Hole Size (A/F)
± .015 L
± .010 HD (A/F)
± HT .005
DMax. (A/F)
Ref. IL
+.004/-.000 Hole Size (A/F)
±.673 .015 .772 .673 .870 .772 .787 .870 .913 .787 1.039 .913 .955 1.039 1.053 .955 1.191 1.053 1.215 1.191 1.215
± .010 .390
± .005 .016
Max. .354
Ref. .469
+.004/-.000 .354
.469 .535
.354 .433
.734
.033
.656
.866
Min. Max. Grip Range
±L .38
± (A/F) .25 HD
±HT .13
DMax. (A/F)
Ref. IL
+.10/-.000 Hole Size (A/F)
1.0 Min. 3.5 1.0 6.0 3.5 0.8 6.0 4.0 0.8 7.0 4.0 1.0 7.0 4.5 1.0 7.5 4.5 1.0 7.5 1.0
17.10 ± .38 19.60 17.10 22.10 19.60 20.00 22.10 23.20 20.00 26.40 23.20 24.25 26.40 26.75 24.25 30.25 26.75 30.85 30.25 30.85
± .25 9.92
± .13 0.41
Max. 8.98
Ref. 11.9
+.10/-.000 9.0
9.92 11.60
0.41 0.41
8.98 10.98
11.9 13.6
9.0 11.0
UNIFIED THREAD (UNITS - INCHES)
.390
.016
.354
.457
.016
.432
.457
.016
.432
.535
.433
.559
.025
.511
.689
.512
.559 .734
.025 .033
.511 .656
.689 .866
.512 .656
.656 FHK - SMALL FLANGE METRIC THREAD (UNITS - MILLIMETERS) Grip Range L HD (A/F) HT D (A/F) IL Hole Size (A/F) fhk Part -SHEREX small flange metric thread unit millimeters ( ) FHK - SMALL FLANGE METRIC THREAD (UNITS - MILLIMETERS) Number Thread Size Metric - Steel SHEREX Part Number FHK2-610-3.5 Metric - Steel FHK2-610-6.0
FHK2-610-3.5 FHK2-610-8.5 FHK2-610-6.0 FHK2-8125-4.0 FHK2-610-8.5 FHK2-8125-7.0 FHK2-8125-4.0 FHK2-8125-10.0 FHK2-8125-7.0 FHK2-1015-4.5 FHK2-8125-10.0 FHK2-1015-7.5 FHK2-1015-4.5 FHK2-1015-10.5 FHK2-1015-7.5 FHK2-12175-4.5 FHK2-1015-10.5 FHK2-12175-4.5
• The FHK series has a small flange for a near flush installation. fhl
-
Thread Size M6 X 1.0 ISO M6 X 1.0 ISO M8 X 1.25 ISO M8 X 1.25 ISO M10 X 1.5 ISO M10XX1.75 1.5 ISO M12 ISO M12 X 1.75 ISO
3.5 Max. 6.0 3.5 8.5 6.0 4.0 8.5 7.0 4.0 10.0 7.0 4.5 10.0 7.5 4.5 10.5 7.5 4.5 10.5 4.5
11.60
0.41
10.98
13.6
11.0
14.20
0.64
12.98
17.5
13.0
14.20 18.65
0.64 0.85
12.98 16.65
17.5 22.0
13.0 16.66
18.65
0.85
16.65
22.0
16.66
largeFHL flange unified thread unit- INCHES) - inches) - LARGE FLANGE UNIFIED THREAD ( (UNITS
SHEREX Part Number Inch - Steel SHEREX Part Number FHL2-2520-138 Inch - Steel FHL2-2520-236
FHL2-2520-138 FHL2-2520-335 FHL2-2520-236 FHL2-3118-157 FHL2-2520-335 FHL2-3118-276 FHL2-3118-157 FHL2-3118-394 FHL2-3118-276 FHL2-3716-177 FHL2-3118-394 FHL2-3716-295 FHL2-3716-177 FHL2-3716-413 FHL2-3716-295 SHEREX Part Number FHL2-3716-413 Inch - Steel SHEREX Part Number LRGH2-5013-177 Inch - Steel LRGH2-5013-177
Grip Range FHLSize - LARGE FLANGE Thread Min. Max. Grip Range Thread Size .039 .138 Min. Max. 1/4-20 UNC .138 .236 .039 .138 .236 .335 1/4-20 UNC .138 .236 .031 .157 5/16-18 UNC .236 .335 .157 .276 .031 .157 .276 .394 5/16-18 UNC .157 .276 .039 .177 3/8-16 UNC .276 .394 .177 .295 .039 .177 .295 .413 3/8-16 UNC Grip Range .177 .295 Thread Size .295 .413 Min. Max. Grip Range Thread Size 1/2-13 UNC .039 .177 Min. Max.
L
HD (A/F)
HT
D (A/F)
IL
Hole Size (A/F)
± .015 L
± .014 HD (A/F)
± .006 HT
Max. D (A/F)
Ref. IL
+.004/-.000 Hole Size (A/F)
±.657 .015 .756 .657 .854 .756 .771 .854 .897 .771 1.020 .897 .910 1.020 1.010 .910 1.140 L 1.010 1.140 ± .015 L ±1.181 .015
± .014 .511
± .006 .059
Max. .354
Ref. .469
+.004/-.000 .354
.511 .630
.059 .059
.354 .432
.469 .535
.354 .433
.630 .748
.059 .079
.432 .511
.535 .689
.433 .512
UNIFIED THREAD (UNITS - INCHES)
HD.748 (A/F)
.079 HT
D.511 (A/F)
.689 IL
.512 (A/F) Hole Size
± .025 HD (A/F) .959 ± .025
± .006 HT .085 ± .006
Max. D (A/F) .656 Max.
Ref. IL .866 Ref.
+.010/-.000 Hole Size (A/F) .656 +.010/-.000
1/2-13 UNC .959 (UNITS .085 - MILLIMETERS) .656 .866 .039 1.181 FHL - LARGE FLANGE.177 METRIC THREAD
.656
Range L HD (A/F) HT (A/F) IL Hole Size (A/F) -SHEREX large flangeGrip metric thread -Dmillimeters (unit ) FHL - LARGE FLANGE METRIC THREAD (UNITS - MILLIMETERS) Part Number Thread Size
fhl
Metric - Steel SHEREX Part Number FHL2-610-3.5 Metric - Steel FHL2-610-6.0
• The FHL series has a large flange to provide increased strength in punched and drilled holes.
FHL2-610-3.5 FHL2-610-8.5 FHL2-610-6.0 FHL2-8125-4.0 FHL2-610-8.5 FHL2-8125-7.0 FHL2-8125-4.0 FHL2-8125-10.0 FHL2-8125-7.0 FHL2-1015-4.5 FHL2-8125-10.0 FHL2-1015-7.5 FHL2-1015-4.5 FHL2-1015-10.5 FHL2-1015-7.5 FHL2-1015-10.5 SHEREX Part Number Metric - Steel SHEREX Part Number LRGH2-12175-4.5 Metric - Steel LRGH2-12175-4.5
Thread Size M6 X 1.0 ISO M6 X 1.0 ISO M8 X 1.25 ISO M8 X 1.25 ISO M10 X 1.5 ISO M10 X 1.5 ISO Thread Size Thread Size M12 X 1.75 ISO M12 X 1.75 ISO
Min. Max. Grip Range
± .38 L
± .35 HD (A/F)
± .15 HT
Max. D (A/F)
Ref. IL
+.10/-.000 Hole Size (A/F)
1.0 3.5 Min. Max. 3.5 6.0 1.0 3.5 6.0 8.5 3.5 6.0 0.8 4.0 6.0 8.5 4.0 7.0 0.8 4.0 7.0 10.0 4.0 7.0 1.0 4.5 7.0 10.0 4.5 7.5 1.0 4.5 7.5 10.5 4.5 7.5 7.5Grip Range 10.5
16.70 ± .38 19.20 16.70 21.70 19.20 19.60 21.70 22.80 19.60 26.00 22.80 23.10 26.00 25.60 23.10 29.10 25.60 L 29.10
± .35 13.00
± .15 1.50
Max. 8.98
Ref. 11.9
+.10/-.000 9.0
13.00 16.00
1.50 1.50
8.98 10.98
11.9 13.6
9.0 11.0
16.00 19.00
1.50 2.00
10.98 12.98
13.6 17.5
11.0 13.0
19.00 HD (A/F)
2.00 HT
12.98 D (A/F)
17.5 IL
13.0 Hole Size (A/F)
Min. Max. Grip Range 1.0 4.5 Min. Max.
± .38 L 30.00 ± .38
± .64 HD (A/F) 24.36 ± .64
± .15 HT 2.16 ± .15
Max. D (A/F) 16.65 Max.
Ref. IL 22.0 Ref.
+.25/-.000 Hole Size (A/F) 16.66 +.25/-.000
30.00
24.36
2.16
16.65
22.0
16.66
1.0
4.5
Sherex full hex rivet nuts are compatible with the following GRADE 2, GRADE 5, CLASS 8.8 and CLASS 9.8 Please contact Sherex when using other grade fasteners.
4
Request Info
1-800-453-1692 www.aboveboardelectronics.com Sherex Fastening Solutions • Phone: 866-474-3739 • Fax: 716-875-0358 • www.sherex.com • E-mail:
[email protected]
IMPERIAL/INCH BODY STYLE RIVET NUTS
IMPERIAL/ INCH BODY STYLE Rivet Nuts
~ ~.
• Imperial/Inch body styles are designed to be placed in fractional or common inch drill/punch hole sizes. • They are the most common styles used in the American marketplace. • Most of the inch/imperial body styles are available with metric threads. • All parts are manufactured by Sherex Taiwan, our ISO/TS 16949 certified production facility. • Special designs are available to meet customer specific requirements. Contact Sherex with your application information.
catalog attributes
-
inch body style
Grip Range Material Thickness L Length HD Head Diameter HT Head Thickness D Diameter
D(A/F) IL LB ILB ITD
Diameter Across Flats Installed Length Length Closed End Installed Length Closed End Installed Thread Depth
Request Info
1-800-453-1692 www.aboveboardelectronics.com Sherex Fastening Solutions • Phone: 866-474-3739 • Fax: 716-875-0358 • www.sherex.com • E-mail:
[email protected]
5
A
P
I
CAL
CAL LARGE FLANGE KNURLED BODY THIN WALL SERIES
series
OPEN END
CLOSED END
HOLE SIZE
HD
• The CAL series has a large flange to provide increased strength in punched and drilled holes. • Knurled body provides a higher resistance to spin out when installed in soft materials.
CLOSED END
WEDGE HEAD
Part Number (Steel) CAL2-0632-080 CAL2-0632-130 unified CAL2-0832-080 CAL2-0832-130 Part Number CAL2-1024-130 (Steel) CAL2-1024-225 CAL2-0632-080 CAL2-1032-130 CAL2-0632-130 CAL2-1032-225 CAL2-0832-080 CAL2-2520-165 CAL2-0832-130 CAL2-2520-260 CAL2-1024-130 CAL2-2528-165 CAL2-1024-225 CAL2-2528-260 CAL2-1032-130 CAL2-3118-150 CAL2-1032-225 CAL2-3118-312 CAL2-2520-165 CAL2-3124-150 CAL2-2520-260 CAL2-3124-312 CAL2-2528-165 CAL2-3716-150 CAL2-2528-260 CAL2-3716-312 CAL2-3118-150 CAL2-3724-150 CAL2-3118-312 CAL2-3724-312 CAL2-3124-150 CAL2-5013-200 CAL2-3124-312 CAL2-5013-350 CAL2-3716-150 CAL2-3716-312 CAL2-3724-150 CAL2-3724-312 CAL2-5013-200 CAL2-5013-350
Grip Range Min. Max. 6-32 UNC .020 .080 6-32 UNC .080 .130 thread unit 8-32 UNC .020 .080 8-32 UNC .080 .130 Thread Size Grip 10-24 UNC .020 Range .130 Min. Max. 10-24 UNC .130 .225 6-32 UNC .020 .080 10-32 UNF .020 .130 6-32 UNC .080 .130 10-32 UNF .130 .225 8-32 UNC .020 .080 1/4-20 UNC .027 .165 8-32 UNC .080 .130 1/4-20 UNC .165 .260 10-24 .020 .130 1/4-28UNC UNF .027 .165 10-24 .130 .225 1/4-28UNC UNF .165 .260 10-32 UNF .020 .130 5/16-18 UNC .027 .150 10-32 UNF .130 .225 5/16-18 UNC .150 .312 1/4-20 UNC .027 .165 5/16-24 UNF .027 .150 1/4-20 UNC .165 .260 5/16-24 UNF .150 .312 1/4-28 .027 .165 3/8-16 UNF UNC .027 .150 1/4-28 .165 .260 3/8-16 UNF UNC .150 .312 5/16-18 UNC .027 .150 3/8-24 UNF .027 .150 5/16-18 UNC .150 .312 3/8-24 UNF .150 .312 5/16-24 UNF .027 .150 1/2-13 UNC .063 .200 5/16-24 UNF .150 .312 1/2-13 UNC .200 .350 3/8-16 UNC .027 .150 3/8-16 UNC .150 .312 3/8-24 UNF .027 .150 3/8-24 UNF .150 .312 1/2-13 UNC .063 .200 1/2-13 UNC .200 .350 THREAD SIZE
(
metric thread
L HD ± .015 ±.010 ±.025* .420 .390 .470 .390 inches .420 .390 .470 .390 L HD .475 .415 ±.585 .015 ±.010.415 ±.025* .420 .390 .475 .415 .470 .390 .585 .415 .420 .390 .580 .500 .470 .390 .680 .500 .475 .415 .580 .500 .585 .415 .680 .500 .475 .415 .690 .685* .585 .415 .805 .685* .580 .500 .690 .685* .680 .500 .805 .685* .580 .500 .690 .685* .680 .500 .805 .685* .690 .685* .690 .685* .805 .685* .805 .685* .690 .685* 1.150 .865* .805 .685* 1.300 .865* .690 .685* .805 .685* .690 .685* .805 .685* 1.150 .865* 1.300 .865*
-
(unit -
)
Stainless Steel 302* Aluminum 5056
RoHS Compliant Finishes: Zinc Plated-Yellow Trivalent Chromate per Sherex SFS-01-001, SC2 Zinc Plated-Clear Trivalent Chromate per Sherex SFS-01-001
HT Hy D ± .003 Max. .030 .265 .030 .265 .030 .265 .030 .265 HT D .030 .296 ±.030 .003 Max. .296 .030 .265 .030 .296 .030 .265 .030 .296 .030 .265 .030 .390 .030 .265 .030 .390 .030 .296 .030 .390 .030 .296 .030 .390 .030 .296 .035 .530 .030 .296 .035 .530 .030 .390 .035 .530 .030 .390 .035 .530 .030 .390 .035 .530 .030 .390 .035 .530 .035 .530 .035 .530 .035 .530 .035 .530 .035 .530 .047 .685 .035 .530 .047 .685 .035 .530 .035 .530 .035 .530 .035 .530 .047 .685 .047 .685
THREAD
IL Max. .305 .305 .305 .305 IL .315 Max. .315 .305 .315 .305 .315 .305 .380 .305 .380 .315 .380 .315 .380 .315 .470 .315 .425 .380 .470 .380 .425 .380 .470 .380 .425 .470 .470 .425 .425 .470 .850 .425 .850 .470 .425 .470 .425 .850 .850
LBSIZE ± .015 .740 .740 .740 .740 LB .990 ±.990 .015 .740 .990 .740 .990 .740 1.190 .740 1.190 .990 1.190 .990 1.190 .990 1.390 .990 1.390 1.190 1.390 1.190 1.390 1.190 1.390 1.190 1.390 1.390 1.390 1.390 1.390 1.390 2.365 1.390 2.365 1.390 1.390 1.390 1.390 2.365 2.365
ILB Max. .640 .580 .640 .580 ILB .845 Max. .735 .640 .845 .580 .735 .640 1.005 .580 .905 .845 1.005 .735 .905 .845 1.175 .735 1.025 1.005 1.175 .905 1.025 1.005 1.175 .905 1.025 1.175 1.175 1.025 1.025 1.175 2.070 1.025 1.920 1.175 1.025 1.175 1.025 2.070 1.920
ITD Ref. .610 .670 .610 .670 ITD .730 Ref. .840 .610 .730 .670 .840 .610 .895 .670 1.035 .730 .895 .840 1.035 .730 .995 .840 1.120 .895 .995 1.035 1.120 .895 .995 1.035 1.120 .995 .995 1.120 1.120 .995 1.505 1.120 1.505 .995 1.120 .995 1.120 1.505 1.505
Hole Size +.006/-.000 .266 .266 .266 .266 Hole Size .297 +.006/-.000 .297 .266 .297 .266 .297 .266 .391 .266 .391 .297 .391 .297 .391 .297 .531 .297 .531 .391 .531 .391 .531 .391 .531 .391 .531 .531 .531 .531 .531 .531 .688 .531 .688 .531 .531 .531 .531 .688 .688
IL Max. 7.75 7.75 8.00 8.00 IL 9.65 Max. 9.65 7.75 11.94 7.75 10.80 8.00 11.94 8.00 10.80 9.65 21.59 9.65 21.59 11.94 10.80 11.94 10.80 21.59 21.59
LB ± .38 18.80 18.80 25.15 25.15 LB 30.23 ± .38 30.23 18.80 35.31 18.80 35.31 25.15 35.31 25.15 35.31 30.23 60.07 30.23 60.07 35.31 35.31 35.31 35.31 60.07 60.07
ILB Max. 16.26 14.73 21.46 18.67 ILB 25.53 Max. 22.99 16.26 29.85 14.73 26.04 21.46 29.85 18.67 26.04 25.53 52.58 22.99 48.77 29.85 26.04 29.85 26.04 52.58 48.77
ITD Ref. 15.49 17.02 18.54 21.34 ITD 22.73 Ref. 26.29 15.49 25.27 17.02 28.45 18.54 25.27 21.34 28.45 22.73 38.23 26.29 38.23 25.27 28.45 25.27 28.45 38.23 38.23
Hole Size +.15/-.000 6.75 6.75 7.60 7.60 Hole Size 10.00 +.15/-.000 10.00 6.75 13.50 6.75 13.50 7.60 13.50 7.60 13.50 10.00 17.45 10.00 17.45 13.50 13.50 13.50 13.50 17.45 17.45
millimeters)
Part Number Thread Size Grip Range L HD (Steel) Min. Max. ± .38 ±.25 ±.64* CAL2-470-2.0 M4x0.7 ISO 0.50 2.00 10.68 9.91 CAL2-470-3.3 M4x0.7 ISO 2.00 3.30 11.94 9.91 CAL2-580-3.3 M5x0.8 ISO 0.50 3.30 12.07 10.54 CAL2-580-5.7 M5x0.8 ISO 3.30 5.70 14.86 10.54 Part Number Thread Grip L HD CAL2-610-4.2 M6x1.0Size ISO 0.70 Range 4.20 14.73 12.70 (Steel) Min. Max. ± .38 ±.25 ±.64* CAL2-610-6.6 M6x1.0 ISO 4.20 6.60 17.27 12.70 CAL2-470-2.0 M4x0.7 ISO 0.50 2.00 10.68 9.91 CAL2-8125-3.8 M8x1.25 ISO 0.70 3.80 17.53 17.40* CAL2-470-3.3 M4x0.7 ISO 2.00 3.30 11.94 9.91 CAL2-8125-7.9 M8x1.25 ISO 3.80 7.90 20.45 17.40* CAL2-580-3.3 M5x0.8 ISO 0.50 3.30 12.07 10.54 CAL2-1015-3.8 M10x1.5 ISO 0.70 3.80 17.53 17.40* CAL2-580-5.7 M5x0.8 ISO 3.30 5.70 14.86 10.54 CAL2-1015-7.9 M10x1.5 ISO 3.80 7.90 20.45 17.40* CAL2-610-4.2 M6x1.0 ISO 4.20 14.73 12.70 CAL2-12175-5.1 M12x1.75 ISO 0.70 1.60 5.10 29.21 21.97* CAL2-610-6.6 M6x1.0 ISO 6.60 17.27 12.70 CAL2-12175-8.9 M12x1.75 ISO 4.20 5.10 8.90 33.02 21.97* CAL2-8125-3.8 M8x1.25 ISO 0.70 3.80 17.53 17.40* CAL2-8125-7.9 M8x1.25 ISO 3.80 7.90 20.45 17.40* part numbering CAL2-1015-3.8 M10x1.5 ISO 0.70 system 3.80 17.53 17.40* CAL2-1015-7.9 M10x1.5 ISO 3.80 7.90 20.45 17.40* Number 21.97* CAL Specifications CAL2-12175-5.1 M12x1.75 ISO 1.60 5.10Part29.21 Material: Steel 1008/1010 CAL2-12175-8.9 M12x1.75 ISO 5.10 8.90Example: 33.02 CAL2-2520-165 21.97*
SEALED HEAD
Thread Size
CAL Product Style Large Flange Knurled Body Thin Wall Series
HT ± .08 0.76 0.76 0.76 0.76 HT 0.76 ±0.76 .08 0.76 0.89 0.76 0.89 0.76 0.89 0.76 0.89 0.76 1.19 0.76 1.19 0.89 0.89 0.89 0.89 1.19 1.19
2 Material 1-Stainless Steel 2-Steel 3-Aluminum
D Max. 6.73 6.73 7.52 7.52 D 9.91 Max. 9.91 6.73 13.46 6.73 13.46 7.52 13.46 7.52 13.46 9.91 17.40 9.91 17.40 13.46 13.46 13.46 13.46 17.40 17.40
2520 Thread Size
165 Grip Range
(_) Empty-Open End B-Closed End T-Clear Trivalent W-Wedge Head S-Sealed
Special finish or material available upon request
*Contact Sherex for exact product dimensions in Stainless Steel. Grip range can be affected by parent material and hole size. Sherex recommends trial installations to determine the proper grip range for the application. Contact Sherex for details. CAL style rivet nuts are available in sealed, closed end, and wedge head designs by special order. Other specials available upon request. Contact Sherex for test data. INSTALLATION TOOLING CAL Series can be installed with our Hand Tools, Pneumatic Tools, and Hydro-Pneumatic Tools. For additional tooling information see pages 38-42. Sherex rivet nuts are compatible with the following hardware: GRADE 2, GRADE 5, CLASS 8.8 and CLASS 9.8 Please contact Sherex when using other grade fasteners.
6
Sherex Fastening Solutions
•
Request Info716-875-0358 Phone: 866-474-3739 • Fax:
1-800-453-1692 E-mail:
[email protected] • www.sherex.com • www.aboveboardelectronics.com
CAK SMALL FLANGE KNURLED BODY THIN WALL SERIES OPEN END
L
series
CLOSED END HOLE SIZE
-
THREAD SIZE
"T IAREA D SIZE
Part Number (Steel) unified CAK2-0632-080 CAK2-0632-130 Part Number CAK2-0832-080 (Steel) CAK2-0832-130 CAK2-1024-130 CAK2-0632-080 CAK2-1024-225 CAK2-0632-130 CAK2-1032-130 CAK2-0832-080 CAK2-1032-225 CAK2-0832-130 CAK2-2520-165 CAK2-1024-130 CAK2-2520-260 CAK2-1024-225 CAK2-2528-165 CAK2-1032-130 CAK2-2528-260 CAK2-1032-225 CAK2-3118-150 CAK2-2520-165 CAK2-3118-312 CAK2-2520-260 CAK2-3124-150 CAK2-2528-165 CAK2-3124-312 CAK2-2528-260 CAK2-3716-150 CAK2-3118-150 CAK2-3716-312 CAK2-3118-312 CAK2-3724-150 CAK2-3124-150 CAK2-3724-312 CAK2-3124-312 CAK2-3716-150 CAK2-3716-312 CAK2-3724-150 CAK2-3724-312
CAK
Grip Range L HD Min. Max. ± .015 ±.010 ±.015* thread 6-32 UNC .020 unit .080 .420inches .310 6-32 UNC .080 .130 .470 .310 Thread Size Grip L HD 8-32 UNC .020 Range .080 .420 .310 Min. .015 ±.010.310 ±.015* 8-32 UNC .080 Max. .130 ±.470 10-24 UNC .020 .080 .130 .475 .340 6-32 UNC .020 .420 .310 10-24 UNC .130 .130 .225 .585 .340 6-32 UNC .080 .470 .310 10-32 UNF .020 .080 .130 .475 .340 8-32 UNC .020 .420 .310 10-32 UNF .130 .130 .225 .585 .340 8-32 UNC .080 .470 .310 1/4-20 UNC .020 .027 .130 .165 .580 .455 10-24 UNC .475 .340 1/4-20 UNC .130 .165 .225 .260 .680 .455 10-24 UNC .585 .340 1/4-28 UNF .020 .027 .130 .165 .580 .455 10-32 UNF .475 .340 1/4-28 UNF .130 .165 .225 .260 .680 .455 10-32 UNF .585 .340 5/16-18 UNC .027 .027 .165 .150 .690 .595* 1/4-20 UNC .580 .455 5/16-18 UNC .165 .150 .260 .312 .805 .595* 1/4-20 UNC .680 .455 5/16-24 UNF .027 .027 .165 .150 .690 .595* 1/4-28 UNF .580 .455 5/16-24 UNF .165 .150 .260 .312 .805 .595* 1/4-28 UNF .680 .455 3/8-16 UNC .027 .150 .150 .690 .595* 5/16-18 UNC .027 .690 .595* 3/8-16 UNC .150 .312 .312 .805 .595* 5/16-18 UNC .150 .805 .595* 3/8-24 UNF .027 .150 .150 .690 .595* 5/16-24 UNF .027 .690 .595* 3/8-24 UNF .150 .312 .312 .805 .595* 5/16-24 UNF .150 .805 .595* 3/8-16 UNC .027 .150 .690 .595* 3/8-16 UNC .150 .312 .805 .595* 3/8-24 UNF .027 .150 .690 .595* 3/8-24 UNF .150 .312 .805 .595* Thread Size
(
metric thread
-
(unit -
)
HT ± .002 .019 .019 HT .019 ±.019 .002 .019 .019 .019 .019 .019 .019 .019 .019 .022 .019 .022 .019 .022 .019 .022 .019 .022 .022 .022 .022 .022 .022 .022 .022 .022 .022 .022 .022 .022 .022 .022 .022 .022 .022 .022 .022
D Max. .265 .265 D .265 Max. .265 .296 .265 .296 .265 .296 .265 .296 .265 .390 .296 .390 .296 .390 .296 .390 .296 .530 .390 .530 .390 .530 .390 .530 .390 .530 .530 .530 .530 .530 .530 .530 .530 .530 .530 .530 .530
IL Max. .305 .305 IL .305 Max. .305 .315 .305 .315 .305 .315 .305 .315 .305 .380 .315 .380 .315 .380 .315 .380 .315 .470 .380 .425 .380 .470 .380 .425 .380 .470 .470 .425 .425 .470 .470 .425 .425 .470 .425 .470 .425
LB ± .015 .740 .740 LB .740 ±.740 .015 .990 .740 .990 .740 .990 .740 .990 .740 1.190 .990 1.190 .990 1.190 .990 1.190 .990 1.390 1.190 1.390 1.190 1.390 1.190 1.390 1.190 1.390 1.390 1.390 1.390 1.390 1.390 1.390 1.390 1.390 1.390 1.390 1.390
ILB Max. .640 .580 ILB .640 Max. .580 .845 .640 .735 .580 .845 .640 .735 .580 1.005 .845 .905 .735 1.005 .845 .905 .735 1.175 1.005 1.025 .905 1.175 1.005 1.025 .905 1.175 1.175 1.025 1.025 1.175 1.175 1.025 1.025 1.175 1.025 1.175 1.025
ITD Ref. .610 .670 ITD .610 Ref. .670 .730 .610 .840 .670 .730 .610 .840 .670 .895 .730 1.035 .840 .895 .730 1.035 .840 .995 .895 1.120 1.035 .995 .895 1.120 1.035 .995 .995 1.120 1.120 .995 .995 1.120 1.120 .995 1.120 .995 1.120
Hole Size +.006/-.000 .266 .266 Hole Size .266 +.006/-.000 .266 .297 .266 .297 .266 .297 .266 .297 .266 .391 .297 .391 .297 .391 .297 .391 .297 .531 .391 .531 .391 .531 .391 .531 .391 .531 .531 .531 .531 .531 .531 .531 .531 .531 .531 .531 .531
D Max. 6.73 6.73 D 7.52 Max. 7.52 9.91 6.73 9.91 6.73 13.46 7.52 13.46 7.52 13.46 9.91 13.46 9.91 13.46 13.46 13.46 13.46
IL Max. 7.75 7.75 IL 8.00 Max. 8.00 9.65 7.75 9.65 7.75 11.94 8.00 10.80 8.00 11.94 9.65 10.80 9.65 11.94 10.80 11.94 10.80
LB ± .38 18.80 18.80 LB 25.15 ± .38 25.15 30.23 18.80 30.23 18.80 35.31 25.15 35.31 25.15 35.31 30.23 35.31 30.23 35.31 35.31 35.31 35.31
ILB Max. 16.26 14.73 ILB 21.46 Max. 18.67 25.53 16.26 22.99 14.73 29.85 21.46 26.04 18.67 29.85 25.53 26.04 22.99 29.85 26.04 29.85 26.04
ITD Ref. 15.49 17.02 ITD 18.54 Ref. 21.34 22.73 15.49 26.29 17.02 25.27 18.54 28.45 21.34 25.27 22.73 28.45 26.29 25.27 28.45 25.27 28.45
Hole Size +.15/-.000 6.75 6.75 Hole Size 7.60 +.15/-.000 7.60 10.00 6.75 10.00 6.75 13.50 7.60 13.50 7.60 13.50 10.00 13.50 10.00 13.50 13.50 13.50 13.50
• The CAK series has a small flange for a near flush installation. • Knurled body provides a higher resistance to spin out when installed in soft materials.
CLOSED END
millimeters)
Part Number Thread Size Grip Range L HD (Steel) Min. Max. ± .38 ±.25 ±.38* CAK2-470-2.0 M4x0.7 ISO 0.50 2.00 10.67 7.87 CAK2-470-3.3 M4x0.7 ISO 2.00 3.30 11.94 7.87 Part Number Thread L HD CAK2-580-3.3 M5x0.8 Size ISO Grip 0.50 Range 3.30 12.07 8.64 (Steel) .38 ±.258.64 ±.38* CAK2-580-5.7 M5x0.8 ISO Min. 3.30 Max. 5.70 ± 14.86 CAK2-610-4.2 M6x1.0 ISO ISO 0.50 0.70 2.00 4.20 10.67 14.73 11.56 CAK2-470-2.0 M4x0.7 7.87 CAK2-610-6.6 M6x1.0 ISO ISO 2.00 4.20 3.30 6.60 11.94 17.27 11.56 CAK2-470-3.3 M4x0.7 7.87 CAK2-8125-3.8 M8x1.25 ISO 0.50 0.70 3.30 3.80 12.07 17.53 15.11* CAK2-580-3.3 M5x0.8 ISO 8.64 CAK2-8125-7.9 M8x1.25 ISO 3.30 3.80 5.70 7.90 14.86 20.45 15.11* CAK2-580-5.7 M5x0.8 ISO 8.64 CAK2-1015-3.8 M10x1.5 ISO 0.70 0.70 4.20 3.80 14.73 17.53 15.11* CAK2-610-4.2 M6x1.0 ISO 11.56 CAK2-1015-7.9 M10x1.5 ISO 4.20 3.80 6.60 7.90 20.45 15.11* CAK2-610-6.6 M6x1.0 ISO 17.27 11.56 CAK2-8125-3.8 M8x1.25 ISO 0.70 3.80 17.53 15.11* CAK2-8125-7.9 M8x1.25 ISO 3.80 7.90 20.45 15.11* CAK2-1015-3.8 M10x1.5 ISO 0.70 3.80 17.53 15.11* part numbering system CAK2-1015-7.9 M10x1.5 ISO 3.80 7.90 20.45 15.11*
HT ± .05 0.48 0.48 HT 0.48 ±0.48 .05 0.55 0.48 0.55 0.48 0.55 0.48 0.55 0.48 0.55 0.55 0.55 0.55 0.55 0.55 0.55 0.55
Part Number Example: CAK2-2520-165
CAK Specifications Material: Steel 1008/1010 Stainless Steel 302* Aluminum 5056 RoHS Compliant Finishes: Zinc Plated-Yellow Trivalent Chromate per Sherex SFS-01-001, SC2 Zinc Plated-Clear Trivalent Chromate per Sherex SFS-01-001
CAK Product Style Small Flange Knurled Body Thin Wall Series
2 Material 1-Stainless Steel 2-Steel 3-Aluminum
2520 Thread Size
165 Grip Range
(_) Empty-Open End B-Closed End T-Clear Trivalent
Special finish or material available upon request
*Contact Sherex for exact product dimensions in Stainless Steel. Grip range can be affected by parent material and hole size. Sherex recommends trial installations to determine the proper grip range for the application. Contact Sherex for details. CAK style rivet nuts are available in closed end designs. Other specials available upon request. Contact Sherex for test data. INSTALLATION TOOLING CAK Series can be installed with our Hand Tools, Pneumatic Tools, and Hydro-Pneumatic Tools. For additional tooling information see pages 38-42. Sherex rivet nuts are compatible with the following hardware: GRADE 2, GRADE 5, CLASS 8.8 and CLASS 9.8 Please contact Sherex when using other grade fasteners.
Sherex Fastening Solutions
•
Request Info 1-800-453-1692 • Fax: 716-875-0358 • www.sherex.com • E-mail:
[email protected] www.aboveboardelectronics.com
Phone: 866-474-3739
7
CAH
CAH HALF HEX BODY LARGE FLANGE THIN WALL SERIES
series
OPEN END
CLOSED END R
HOLE SIZE
.
411 4
PartHDNumber Thread Size Grip Range L HD (Steel) Min. Max. ± .015 ±.010 ±.025* THREAD CAH2-0632-080 6-32 .020 .080 .385 .375 SIZEUNC CAH2-0632-130 6-32 UNC .080 .130 .435 .375 CAH2-0832-080 8-32 UNC .020 .080 .385 .375 unified inches CAH2-0832-130 thread 8-32 UNC .080unit .130 .435 .375 CAH2-1024-130 10-24 UNC .020 .130 .435 .390 Part Number Thread Size Grip L HD CAH2-1024-225 10-24 UNC .130 Range .225 .535 .390 (Steel) Min. .130 Max. ±.435 .015 ±.010 ±.025* CAH2-1032-130 10-32 UNF .020 .390 CAH2-0632-080 6-32 UNC .020 .225 .080 .385 .375 CAH2-1032-225 10-32 UNF .130 .535 .390 CAH2-0632-130 6-32 UNC .080 .165 .130 .435 .375 CAH2-2520-165 1/4-20 UNC .027 .585 .510 CAH2-0832-080 8-32 UNC .020 .260 .080 .385 .375 CAH2-2520-260 1/4-20 UNC .165 .685 .510 CAH2-0832-130 8-32 UNC .080 .165 .130 .435 .375 CAH2-2528-165 1/4-28 UNF .027 .585 .510 CAH2-1024-130 10-24 UNC .020 .260 .130 .435 .390 CAH2-2528-260 1/4-28 UNF .165 .685 .510 CAH2-1024-225 5/16-18 10-24 UNC .130 .150 .225 .535 .390 CAH2-3118-150 UNC .027 .685 .655* CAH2-1032-130 10-32 UNF .020 .130 .435 .390 CAH2-3118-312 5/16-18 UNC .150 .312 .845 .655* CAH2-1032-225 10-32 UNF .130 .225 .535 .390 CAH2-3124-150 5/16-24 UNF .027 .150 .685 .655* CAH2-2520-165 1/4-20 UNC .027 .165 .585 .510 CAH2-3124-312 5/16-24 UNF .150 .312 .845 .655* CAH2-2520-260 1/4-20 UNC .165 .260 .685 .510 CAH2-3716-150 3/8-16 UNC .027 .150 .685 .655* CAH2-2528-165 1/4-28 UNF .027 .165 .585 .510 CAH2-3716-312 3/8-16 .150 .845 .655* CAH2-2528-260 1/4-28 UNC UNF .165 .312 .260 .685 .510 CAH2-3724-150 3/8-24 UNF .685 .655* CAH2-3118-150 5/16-18 UNC .027 .027 .150 .150 .685 .655* CAH2-3724-312 3/8-24 UNF .845 .655* CAH2-3118-312 5/16-18 UNC .150 .150 .312 .312 .845 .655*
-
(
• The CAH series offers a semi hex body for excellent resistance to spin out in the hole.
CLOSED END
CAH2-3124-150 CAH2-3124-312 CAH2-3716-150 CAH2-3716-312 CAH2-3724-150 CAH2-3724-312
5/16-24 UNF 5/16-24 UNF 3/8-16 UNC 3/8-16 UNC 3/8-24 UNF 3/8-24 UNF
.027 .150 .027 .150 .027 .150
metric thread
SEALED HEAD
Part Number (Steel) CAH2-470-2.0 CAH2-470-3.3 CAH2-580-3.3 Part Number CAH2-580-5.7 (Steel) CAH2-610-4.2 CAH2-470-2.0 CAH2-610-6.6 CAH2-470-3.3 CAH2-8125-3.8 CAH2-580-3.3 CAH2-8125-7.9 CAH2-580-5.7 CAH2-1015-3.8 CAH2-610-4.2 CAH2-1015-7.9
.150 .312 .150 .312 .150 .312
.685 .845 .685 .845 .685 .845
(unit -
Thread Size Grip Range Min. Max. M4x0.7 ISO 0.50 2.00 M4x0.7 ISO 2.00 3.30 M5x0.8 ISO 0.50 3.30 Thread Size Grip M5x0.8 ISO 3.30 Range 5.70 Min. 4.20 Max. M6x1.0 ISO 0.70 M4x0.7 ISO 0.50 6.60 2.00 M6x1.0 4.20 M4x0.7 ISO 2.00 3.80 3.30 M8x1.25 ISO 0.70 M5x0.8 ISO 0.50 7.90 3.30 M8x1.25 ISO 3.80 M5x0.8 ISO 3.30 3.80 5.70 M10x1.5 ISO 0.70 M6x1.0 ISO 0.70 7.90 4.20 M10x1.5 ISO 3.80
)
.655* .655* .655* .655* .655* .655*
HT D (A/F) ± .003 Max. .027 .249 .027 .249 .027 .249 .027 .249 .027 .280 (A/F) D.280 HT .027 ±.027 .003 .280 Max. .249 .027 .280 .027 .249 .030 .374 .027 .249 .030 .374 .027 .249 .030 .374 .027 .280 .030 .374 .027 .280 .035 .499 .027 .280 .035 .499 .027 .280 .035 .499 .030 .374 .035 .499 .030 .374 .035 .499 .030 .374 .035 .499 .030 .374 .035 .499 .035 .499 .035 .499 .035 .499 .035 .035 .035 .035 .035 .035
.499 .499 .499 .499 .499 .499
IL Max. .295 .295 .295 .295 .275 IL .275 Max. .275 .295 .275 .295 .400 .295 .400 .295 .400 .275 .400 .275 .530 .275 .515 .275 .530 .400 .515 .400 .530 .400 .515 .400 .530 .530 .515 .515
LB ± .015 .740 .740 .740 .740 1.030 LB 1.030 ± .015 1.030 .740 1.030 .740 1.190 .740 1.190 .740 1.190 1.030 1.190 1.030 1.445 1.030 1.445 1.030 1.445 1.190 1.445 1.190 1.445 1.190 1.445 1.190 1.445 1.445 1.445 1.445
ILB Max. .640 .580 .640 .580 .845 ILB .735 Max. .845 .640 .735 .580 1.015 .640 .915 .580 1.015 .845 .915 .735 1.235 .845 1.220 .735 1.235 1.015 1.220 .915 1.235 1.015 1.220 .915 1.235 1.235 1.220 1.220
ITD Hole Size (A/F) Ref. +.004/-.000 .575 .250 .640 .250 .575 .250 .640 .250 .695 .281 ITD Hole .281 Size (A/F) .805 Ref. +.004/-.000 .695 .281 .575 .250 .805 .281 .640 .250 .945 .375 .575 .250 1.085 .375 .640 .250 .945 .375 .695 .281 1.085 .375 .805 .281 1.045 .500 .695 .281 1.170 .500 .805 .281 1.045 .500 .945 .375 1.170 .500 1.085 .375 1.045 .500 .945 .375 1.170 .500 1.085 .375 1.045 .500 1.045 .500 1.170 .500 1.170 .500
.530 .515 .530 .515 .530 .515
1.445 1.445 1.445 1.445 1.445 1.445
1.235 1.220 1.235 1.220 1.235 1.220
1.045 1.170 1.045 1.170 1.045 1.170
IL Max. 7.49 7.49 6.99 IL 6.99 Max. 10.16 7.49 10.16 7.49 13.46 6.99 13.08 6.99 13.46 10.16 13.08
LB ± .38 18.80 18.80 26.16 LB 26.16 ± .38 30.23 18.80 30.23 18.80 36.70 26.16 36.70 26.16 36.70 30.23 36.70
ILB Max. 16.26 14.73 21.46 ILB 18.67 Max. 25.78 16.26 23.24 14.73 31.37 21.46 30.99 18.67 31.37 25.78 30.99
ITD Hole Size (A/F) Ref. +.10/-.000 14.61 6.35 16.26 6.35 17.65 7.14 Size (A/F) ITD Hole 7.14 20.45 Ref. +.10/-.000 24.00 9.53 14.61 6.35 27.56 9.53 16.26 6.35 26.54 12.70 17.65 7.14 29.72 12.70 20.45 7.14 26.54 12.70 24.00 9.53 29.72 12.70
THREAD SIZE
.500 .500 .500 .500 .500 .500
millimeters)
L ± .38 9.78 11.05 11.05 L 13.59 ± .38 14.86 9.78 17.40 11.05 17.40 11.05 21.46 13.59 17.40 14.86 21.46
HD ±.25 ±.64* 9.53 9.53 9.91 HD 9.91 ±.25 ±.64* 12.96 9.53 12.96 9.53 16.64* 9.91 16.64* 9.91 16.64* 12.96 16.64*
HT D (A/F) ± .08 Max. 0.68 6.35 0.68 6.35 0.68 7.10 D7.10 (A/F) HT 0.68 ± .08 Max. 0.76 9.50 0.68 6.35 0.76 9.50 0.68 6.35 0.89 12.70 0.68 7.10 0.89 12.70 0.68 7.10 0.89 12.70 0.76 9.50 0.89 12.70
CAH2-610-6.6 M6x1.0 ISO 4.20 6.60 17.40 12.96 0.76 CAH2-8125-3.8 M8x1.25 ISO 0.70 3.80 17.40 16.64* 0.89 CAH2-8125-7.9 M8x1.25 ISO 3.80 7.90 21.46 16.64* 0.89 part numbering CAH2-1015-3.8 M10x1.5 ISO 0.70 system 3.80 17.40 16.64* 0.89 CAH2-1015-7.9 M10x1.5 ISO 3.80 7.90 21.46 16.64* 0.89 Part Number CAH Specifications Example: CAH2-2520-165 Material: Steel 1008/1010 Stainless Steel 302* CAH 2 Aluminum 5056 Product Style Material RoHS Compliant Finishes: Semi Hex 1-Stainless Steel Zinc Plated-Yellow Trivalent Chromate Thin Wall Series 2-Steel per Sherex SFS-01-001, SC2 3-Aluminum Zinc Plated-Clear Trivalent Chromate per Sherex SFS-01-001
9.50 12.70 12.70 12.70 12.70
10.16 13.46 13.08 13.46 13.08
2520 Thread Size
30.23 36.70 36.70 36.70 36.70
23.24 31.37 30.99 31.37 30.99
165 Grip Range
27.56 26.54 29.72 26.54 29.72
9.53 12.70 12.70 12.70 12.70
(_) Empty-Open End Clear B-Closed End T-Clear Trivalent
Special finish or material available upon request
*Contact Sherex for exact product dimensions in Stainless Steel. Grip range can be affected by parent material and hole size. Sherex recommends trial installations to determine the proper grip range for the application. Contact Sherex for details. CAH style rivet nuts are available in sealed head and closed end designs. Other specials available upon request. Contact Sherex for test data. INSTALLATION TOOLING CAH Series can be installed with our Hand Tools, Pneumatic Tools, and Hydro-Pneumatic Tools. For additional tooling information see pages 38-42. Sherex rivet nuts are compatible with the following hardware: GRADE 2, GRADE 5, CLASS 8.8 and CLASS 9.8 Please contact Sherex when using other grade fasteners.
8 SHEREI FASITIVIIC 501,1110149
Sherex Fastening Solutions
•
Request Info E-mail:
[email protected] • Fax: 716-875-0358 • www.sherex.com •1-800-453-1692 www.aboveboardelectronics.com
Phone: 866-474-3739
CA HEAVY DUTY RIVET NUT FLAT HEAD SERIES
CA
series
GR HOLE SIZE
HD THREAD SIZE
unified thread Part Number (Steel) CA-0440S-060 CA-0440S-085 CA-0440S-110 CA-0632S-075 CA-0632S-120 CA-0632S-160 CA-0832S-075 CA-0832S-120 CA-0832S-160 CA-1024S-080 CA-1024S-130 CA-1024S-180 CA-1032S-080 CA-1032S-130 CA-1032S-180 CA-2520S-080 CA-2520S-140 CA-2520S-200 CA-3118S-125 CA-3118S-200 CA-3118S-275 CA-3716S-115 CA-3716S-200 CA-3716S-285 CA-5013S-150 CA-5013S-250 CA-5013S-350
(unit -
Thread Size 4-40 UNC 4-40 UNC 4-40 UNC 6-32 UNC 6-32 UNC 6-32 UNC 8-32 UNC 8-32 UNC 8-32 UNC 10-24 UNC 10-24 UNC 10-24 UNC 10-32 UNF 10-32 UNF 10-32 UNF 1/4-20 UNC 1/4-20 UNC 1/4-20 UNC 5/16-18 UNC 5/16-18 UNC 5/16-18 UNC 3/8-16 UNC 3/8-16 UNC 3/8-16 UNC 1/2-13 UNC 1/2-13 UNC 1/2-13 UNC
inches)
Grip Range Min. Max. .010 .060 .060 .085 .085 .100 .010 .075 .075 .120 .120 .160 .010 .075 .075 .120 .120 .160 .010 .080 .080 .130 .130 .180 .010 .080 .080 .130 .130 .180 .020 .080 .080 .140 .140 .200 .030 .125 .125 .200 .200 .275 .030 .115 .115 .200 .200 .285 .050 .150 .150 .250 .250 .350
L HD HT ± .015 ± .015 Nom. .345 .270 .025 .370 .270 .025 .400 .270 .025 .438 .325 .032 .500 .325 .032 .500 .325 .032 .438 .357 .032 .500 .357 .032 .500 .357 .032 .531 .406 .038 .594 .406 .038 .641 .406 .038 .531 .406 .038 .594 .406 .038 .641 .406 .038 .625 .475 .058 .687 .475 .058 .750 .475 .058 .750 .665 .062 .875 .665 .062 .937 .655 .062 .844 .781 .088 .938 .781 .088 1.031 .781 .088 .906 .906 .085 1.031 .906 .085 1.141NW .906 NW .085
•
D IL Hole Size +.000/-.004 Ref. +.003/-.000 .155 .230 .155 .155 .230 .155 .155 .230 .155 .189 .300 .189 .189 .315 .189 .189 .270 .189 .221 .300 .221 .221 .315 .221 .221 .270 .221 .250 .380 .250 .250 .390 .250 .250 .390 .250 .250 .380 .250 .250 .390 .250 .250 .390 .250 .332 .450 .332 .332 .450 .332 .332 .450 .332 .413 .505 .413 .413 .555 .413 .413 .540 .413 .490 .585 .490 .490 .490 .595 .490 .605 .490 .625 .605 .625 .625 .630 .625 NW NW .625 .625NW .640
part numbering system CA Specifications Material: Steel 1008/1010/1110 Non-Magnetic Stainless Steel 302 Stainless Steel 430 Aluminum 5056/6053 RoHS Compliant Finish: Zinc Plated-Clear Trivalent Chromate per Sherex SFS-01-001
• The CA series offers a thick head and thick collapse chamber wall thickness for heavy duty applications. • Available with a countersunk head style for a flush installation. • Available in a keyed head style for reduced spin out.
CLOSED END
COUNTERSUNK HEAD
Part Number Example: CA-2520S-080 CA Product Style Heavy Duty Large Flange Smooth Shank
2520 Thread Size
Material S-Steel A-Aluminum SS-Stainless Steel 430 NM-Stainless Steel 302
(_) Empty-Open End B-Closed End T-Clear Trivalent
080 Grip Range
Special finish or material available upon request Grip range can be affected by parent material and hole size. Sherex recommends trial installations to determine the proper grip range for the application. Contact Sherex for details. CA style rivet nuts are available in closed end, keyed, and countersunk head designs. Other specials available upon request. Contact Sherex for test data. INSTALLATION TOOLING CA Series can be installed with our Hand Tools, and Hydro-Pneumatic Tools. For additional tooling information see pages 38-42. Sherex rivet nuts are compatible with the following hardware: GRADE 2, GRADE 5, CLASS 8.8 and CLASS 9.8 Please contact Sherex when using other grade fasteners.
Sherex Fastening Solutions
•
Request Info E-mail:
[email protected] • Fax: 716-875-0358 • www.sherex.com • 1-800-453-1692 www.aboveboardelectronics.com
Phone: 866-474-3739
KEYED HEAD
Sherex manufacturers NAS 1329 and NAS 1330 style Rivet Nuts. See page 33 for details. 9
CAO
CAO SMALL FLANGE SMOOTH BODY THIN WALL SERIES
series
GR
• The CAO series offers body diameters that will fit in common hole sizes. • The small flange head also allows for near flush installations.
Part Number Thread Size Grip Range L HD (Steel) Min. Max. THREAD ± .015SIZE ± .010 ±.015* CAO2-0632-080 6-32 UNC .020 .080 .385 .295 CAO2-0832-080 8-32 UNC .020 .080 .385 .295 CAO2-1024-130 10-24 UNC .020 .130 .440 .320 CAO2-1032-130 10-32 UNF .020 .130 .440 .320 CAO2-2520-165 1/4-20 UNCunit .580 .425 unified thread inches ( .030 -.165 ) CAO2-2528-165 1/4-28 UNF .030 .165 .580 .425 CAO2-3118-200 5/16-18 UNC .040 .200 .690 .560* Part Number Thread Size Grip Range L HD CAO2-3124-200 5/16-24 UNF .040 .200 .690 .560* (Steel) Min. Max. ± .015 ± .010 ±.015* CAO2-3716-200 3/8-16 UNC .040 .200 .690 .560* CAO2-0632-080 6-32 UNC .020 .200 .080 .385 .295 CAO2-3724-200 3/8-24 UNF .040 .690 .560* CAO2-0832-080 8-32 UNC .020 .080 .385 .295 CAO2-1024-130 10-24 UNC .020 .130 .440 .320 CAO2-1032-130 10-32 UNF .020 .130 .440 .320 CAO2-2520-165 1/4-20 UNC .030 .165 .580 .425 CAO2-2528-165 1/4-28 UNF .030 .165 .580 .425 CAO2-3118-200 5/16-18 UNC .040 .200 .690 .560* CAO2-3124-200 5/16-24 UNF .040 .200 .690 .560* CAO2-3716-200 3/8-16 UNC .040 .200 .690 .560* CAO2-3724-200 3/8-24 UNF .040 .200 .690 .560*
metric thread CLOSED END
HOLE SIZE
(unit -
Part Number (Steel)
Thread Size
CAO2-470-2.0 CAO2-580-3.3 CAO2-610-4.2 CAO2-8125-5.1 CAO2-1015-5.1
M4x0.7 ISO M5x0.8 ISO M6x1.0 ISO M8x1.25 ISO M10x1.5 ISO
Part Number (Steel)
Thread Size
D Max. .249 .249 .280 .280 .374 .374 .499 D .499 Max. .499 .249 .499 .249 .280 .280 .374 .374 .499 .499 .499 .499
IL Max. .315 .315 .330 .330 .440 .440 .540 IL .540 Max. .540 .315 .540 .315 .330 .330 .440 .440 .540 .540 .540 .540
Hole Size +.006/-.000 .250 .250 .281 .281 .375 .375 .500 Hole Size .500 +.006/-.000 .500 .250 .500 .250 .281 .281 .375 .375 .500 .500 .500 .500
HT ± .08 0.46 0.51 0.56 0.56 0.56
D Max. 6.32 7.11 9.50 12.67 12.67
IL Max. 8.00 8.38 11.18 13.72 13.72
Hole Size +.15/-.000 6.40 7.20 9.60 12.70 12.70
HT ± .08 0.46 0.51 0.56 0.56 0.56
D Max. 6.32 7.11 9.50 12.67 12.67
IL Max. 8.00 8.38 11.18 13.72 13.72
Hole Size +.15/-.000 6.40 7.20 9.60 12.70 12.70
millimeters)
Grip Range Min. Max. 0.50 2.00 0.50 3.30 0.76 4.20 1.02 5.10 1.02 5.10
L ± .38 9.78 11.18 14.73 17.53 17.53
HD ± .25 ± .38* 7.49 8.13 10.80 14.22* 14.22*
Grip Range L ± Min. Max. ± .38 CAO2-470-2.0 M4x0.7 ISO 0.50 2.00 9.78 part numbering system CAO2-580-3.3 M5x0.8 ISO 0.50 3.30 11.18 CAO2-610-4.2 0.76Part 4.20 CAO Specifications M6x1.0 ISO Number 14.73 Material: Steel 1008/1010 CAO2-8125-5.1 M8x1.25 ISO 1.02Example: 5.10 CAO2-2520-165 17.53 Aluminum 5056 CAO2-1015-5.1 M10x1.5 ISO 1.02 5.10 17.53
HT ± .003 .018 .018 .020 .020 .022 .022 .022 HT .022 ± .003 .022 .018 .022 .018 .020 .020 .022 .022 .022 .022 .022 .022
CAO Product Style Low Profile RoHS Compliant Finishes: Inch: Zinc Plated-Clear Trivalent Chromate Smooth Shank Thin Wall Series per Sherex SFS-01-001
HD .25 ± .38* 7.49 8.13 10.80 14.22* 14.22*
2 Material 2-Steel 3-Aluminum
2520 Thread Size
165 Grip Range
(_) Empty-Open End B-Closed End T-Clear Trivalent
Metric: Zinc Plated-Yellow Trivalent Chromate per Sherex SFS-01-001, SC2
Special finish or material available upon request
Grip range can be affected by parent material and hole size. Sherex recommends trial installations to determine the proper grip range for the application. Contact Sherex for details. Contact Sherex for test data. INSTALLATION TOOLING CAO Series can be installed with our Hand Tools, Pneumatic Tools, and Hydro-Pneumatic Tools. For additional tooling information see pages 38-42. Sherex rivet nuts are compatible with the following hardware: GRADE 2, GRADE 5, CLASS 8.8 and CLASS 9.8 Please contact Sherex when using other grade fasteners.
10
S r -41144.-
Request Info 1-800-453-1692 Sherex Fastening Solutions • Phone: 866-474-3739 • Fax: 716-875-0358 • www.sherex.com • E-mail:
[email protected] www.aboveboardelectronics.com
CFW/CAW DIAMOND KNURLED 3600 SWAGING SERIES HD
HOLE SIZE
CFW/ CAW series
THREAD SIZE Material thickness .0132"/1.57 min
Part Number
Thread Size
Cadmium Free &
6-32 UNC 8-32 UNC Thread Size 10-24 UNC 10-32 UNF 6-32 UNC 1/4-20 UNC 8-32 UNC 5/16-18 UNC 10-24 UNC 3/8-16 UNC 10-32 UNF
N Free Cadmium & N RoHS Compliant N NN NN NN NN
1/4-20 UNC 6-32 UNC 5/16-18 UNC 8-32 UNC 3/8-16 UNC 10-24 UNC 10-32 UNF 6-32 UNC 1/4-20 UNC 8-32 UNC 5/16-18 UNC 10-24 UNC 3/8-16 UNC 10-32 UNF 1/4-20 UNC 5/16-18 UNC 3/8-16 UNC
unified thread (Steel) CAW2-0632 Part Number CAW2-0832 (Steel) CAW2-1024 CAW2-1032 CAW2-0632 CAW2-2520 CAW2-0832 CAW2-3118 CAW2-1024 CAW2-3716 CAW2-1032 CAW2-2520 CFW2-0632 CAW2-3118 CFW2-0832 CAW2-3716 CFW2-1024 CFW2-1032 CFW2-0632 CFW2-2520 CFW2-0832 CFW2-3118 CFW2-1024 CFW2-3716 CFW2-1032 CFW2-2520 CFW2-3118 CFW2-3716
metric thread
HD ± .005
L ± .015
D Max.
Hole Size +.005/-.00
.255 HD .285 ±.320 .005 .320 .255 .415 .285 .550 .320 .615 .320
.370 L .370 ±.370 .015 .370 .370 .515 .370 .615 .370 .740 .370
.233 D .264 Max. .295 .295 .233 .389 .264 .528 .295 .590 .295
.234 Hole Size .266 +.005/-.00 .297
N NY NY Y YY YY YY YY
.415 .255 .550 .285 .615 .320 .320 .255 .415 .285 .550 .320 .615 .320
.515 .370 .615 .370 .740 .370 .370 .370 .515 .370 .615 .370 .740 .370
.389 .233 .528 .264 .590 .295 .295 .233 .389 .264 .528 .295 .590 .295
.297 .234 .391 .266 .531 .297 .594 .297 .391 .234 .531 .266 .594 .297 .297 .234 .391 .266 .531 .297 .594 .297
Y Y Y
.415 .550 .615
.515 .615 .740
.389 .528 .590
.391 .531 .594
- inches Compliant) (unit RoHS
(unit -
millimeters)
Part Number (Steel)
Thread Size
Cadmium Free & RoHS Compliant
HD ± .13
L ± .38
D Max.
Hole Size +.13/-.00
CAW2-470 Part Number CAW2-580 (Steel) CAW2-610 CAW2-8125 CAW2-470 CAW2-1015 CAW2-580
M4X0.7 ISO M5X0.8 ISO Thread Size M6X1.0 ISO M8X1.25 ISO M4X0.7 ISO M10X1.5 ISO M5X0.8 ISO
N Free Cadmium N & RoHS Compliant N NN NN
7.24 HD 8.13 ±10.54 .13 13.97 7.24 15.62 8.13
9.40 L 9.40 ± .38 13.08 15.62 9.40 18.80 9.40
6.71 D 7.50 Max. 9.88 13.41 6.71 14.99 7.50
6.75 Hole Size 7.54 +.13/-.00 9.92 13.49 6.75 15.00 7.54
10.54 7.24 13.97 8.13 15.62 10.54 13.97 7.24 15.62 8.13 10.54 13.97 15.62
13.08 9.40 15.62 9.40 18.80 13.08 15.62 9.40 18.80 9.40 13.08 15.62 18.80
9.88 6.71 13.41 7.50 14.99 9.88 13.41 6.71 14.99 7.50 9.88 13.41 14.99
9.92 6.75 13.49 7.54 15.00 9.92 13.49 6.75 15.00 7.54 9.92 13.49 15.00
CAW2-610 M6X1.0 ISO CFW2-470 M4X0.7 ISO CAW2-8125 M8X1.25 ISO CFW2-580 M5X0.8 ISO CAW2-1015 M10X1.5 ISO CFW2-610 M6X1.0 ISO CFW2-8125 M8X1.25 ISO CFW2-470 M4X0.7 ISO CFW2-1015 M10X1.5 ISO CFW2-580 M5X0.8 ISO CFW2-610 M6X1.0 ISO CFW2-8125 M8X1.25 ISO part numbering system CFW2-1015 M10X1.5 ISO
N NY NY Y Y Y Y Y Y Y Y
CFW/CAW Specifications Material: Stainless Steel, 304 L Steel, 12L14 Steel, 1215
• The CFW/CAW series offers a knurled body for increased spin out resistance in soft materials such as fiberglass and plywood. • Increased wall thickness gives increased shear strength. • Cadmium Free finish allows the CFW Series to be used in any industry, including automotive.
Part Number Example: CAW2-2520 CAW Cadmium W series Featuring 3600 Swaging
Finish:
CAW is Cadmium Plated per QQ-P-416 Type 1, Class 3 with clear protective coating
CFW is Proprietary Tin Plated
2 Material 1-Stainless Steel 2-Steel
2520 Thread Size
Special finish or material available upon request
*CFW and CAW rivet nut styles are dimensionally the same. CFW is Cadmium Free and RoHS Compliant. Actual hole size can be affected by parent material and material thickness. Contact Sherex for details. CFW/CAW series available in different finishes. Other specials available upon request. Contact Sherex for test data. INSTALLATION TOOLING CFW/CAW Series can be installed with our Hand Tools, Pneumatic Tools, and Hydro-Pneumatic Tools.
For additional tooling information see pages 38-42.
Sherex rivet nuts are compatible with the following hardware: GRADE 2, GRADE 5, CLASS 8.8 and CLASS 9.8 Please contact Sherex when using other grade fasteners.
Sherex Fastening Solutions
•
Request Info E-mail:
[email protected] • Fax: 716-875-0358 • www.sherex.com •1-800-453-1692 www.aboveboardelectronics.com
Phone: 866-474-3739
11
CFT/ CAT series
CFT/CAT KNURLED 3600 SWAGING SERIES
Ho
Material thickness
r-
Material thickness
HP
HOLE SIZE
HOLE SIZE
Recommended Hole Size +.005/-.00 Part Number (Steel)
Thread Size
CAT2-0440 CAT2-0632 CAT2-0832 CAT2-1024 Part Number CAT2-1032 (Steel) CAT2-2520 CAT2-0440 CAT2-3118 CAT2-0632 CAT2-3716 CAT2-0832 CAT2-5013 CAT2-1024 CAT2-1032 CFT2-0440 CAT2-2520 CFT2-0632 CAT2-3118 CFT2-0832 CAT2-3716 CFT2-1024 CAT2-5013 CFT2-1032
4-40 UNC 6-32 UNC 8-32 UNC 10-24 UNC Thread Size 10-32 UNF 1/4-20 UNC 4-40 UNC 5/16-18 UNC 6-32 UNC 3/8-16 UNC 8-32 UNC 1/2-13 UNC 10-24 UNC 10-32 UNF 4-40 UNC 1/4-20 UNC 6-32 UNC 5/16-18 UNC 8-32 UNC 3/8-16 UNC 10-24 UNC 1/2-13 UNC 10-32 UNF
CFT2-2520 CFT2-0440 CFT2-3118 CFT2-0632 CFT2-3716 CFT2-0832 CFT2-5013 CFT2-1024 CFT2-1032 CFT2-2520 CFT2-3118 CFT2-3716 CFT2-5013
1/4-20 UNC 4-40 UNC 5/16-18 UNC 6-32 UNC 3/8-16 UNC 8-32 UNC 1/2-13 UNC 10-24 UNC 10-32 UNF 1/4-20 UNC 5/16-18 UNC 3/8-16 UNC 1/2-13 UNC
unified thread
• The CFT/CAT series offers one rivet nut for materials of any thickness greater than .030 inches. • Cadmium Free finish allows the CFT Series to be used in any industry, including automotive. • Designed to be used in metal applications.
metric thread
Cadmium Free & RoHS Compliant
HD ± .005
L ± .015
D Max.
N N Cadmium N Free & N RoHS Compliant N N N N N N N N N Y N Y N Y N Y N Y
.211 .240 .269 .306 HD ±.306 .005 .400 .211 .528 .240 .588 .269 .800 .306 .306 .211 .400 .240 .528 .269 .588 .306 .800 .306
.370 .370 .370 .370 L ±.370 .015 .515 .370 .615 .370 .745 .370 .935 .370 .370 .370 .515 .370 .615 .370 .745 .370 .935 .370
.1875 .2185 .2495 .2805 D .2805 Max. .3745 .1875 .4995 .2185 .5615 .2495 .7485 .2805 .2805 .1875 .3745 .2185 .4995 .2495 .5615 .2805 .7485 .2805
Y Y Y Y Y Y Y Y Y Y Y Y Y
.400 .211 .528 .240 .588 .269 .800 .306 .306 .400 .528 .588 .800
.515 .370 .615 .370 .745 .370 .935 .370 .370 .515 .615 .745 .935
.3745 .1875 .4995 .2185 .5615 .2495 .7485 .2805 .2805 .3745 .4995 .5615 .7485
(unit N
(unit -
inches)
MAT. THICK .030-.090
MAT. THICK .091-.124
MAT. THICK .125-.186
MAT. THICK .187-Over
.1875 .1935 .1935 .1960 .2188 .2210 .2280 .2280 Recommended Hole Size +.005/-.00 .2500 .2570 .2656 .2656 .2812 .2900 .2900 .2969 MAT. THICK MAT. THICK MAT. THICK MAT. THICK .2812 .2900 .2900 .2969 .030-.090 .091-.124 .125-.186 .187-Over .3750 .3750 .3860 .3906 .1875 .1935 .1935 .1960 .5000 .5000 .5156 .5156 .2188 .2210 .2280 .2280 .5625 .5625 .5781 .5781 .2500 .2570 .2656 .2656 .7500 .7656 .7810 .7970 .2812 .2900 .2900 .2969 .2812 .2900 .2900 .2969 .1875 .1935 .1935 .1960 .3750 .3750 .3860 .3906 .2188 .2210 .2280 .2280 .5000 .5000 .5156 .5156 .2500 .2570 .2656 .2656 .5625 .5625 .5781 .5781 .2812 .2900 .2900 .2969 .7500 .7656 .7810 .7970 .2812 .2900 .2900 .2969 .3750 .1875 .5000 .2188 .5625 .2500 .7500 .2812 .2812 .3750 .5000 .5625 .7500
.3750 .1935 .5000 .2210 .5625 .2570 .7656 .2900 .2900 .3750 .5000 .5625 .7656
.3860 .1935 .5156 .2280 .5781 .2656 .7810 .2900 .2900 .3860 .5156 .5781 .7810
.3906 .1960 .5156 .2280 .5781 .2656 .7970 .2969 .2969 .3906 .5156 .5781 .7970
millimeters) Recommended Hole Size +.13/-.00
Part Number (Steel)
Thread Size
Cadmium Free & RoHS Compliant
CAT2-350 M3X0.5 ISO N CAT2-470 M4X0.7 ISO N CAT2-580 M5X0.8 ISO N Cadmium CAT2-610 M6X1.0 ISO N Free Part Number & Thread Size CAT2-8125 M8X1.25 ISO N (Steel) RoHS Compliant CAT2-1015 M10X1.5 ISO N CAT2-350 M3X0.5 ISO N CAT2-12175 M12X1.75 ISO N CAT2-470 M4X0.7 ISO N CAT2-580 M5X0.8 ISO N CFT2-350 M3X0.5 ISO Y CAT2-610 M6X1.0 ISO N CFT2-470 M4X0.7 ISO Y CAT2-8125 M8X1.25 ISO N CFT2-580 M5X0.8 ISO Y CAT2-1015 M10X1.5 ISO N CFT2-610 M6X1.0 ISO Y CAT2-12175 M12X1.75 ISO N CFT2-8125 M8X1.25 ISO Y CFT2-1015 M10X1.5 ISO Y CFT2-350 M3X0.5 ISO Y CFT2-12175 M12X1.75 ISO Y CFT2-470 M4X0.7 ISO Y CFT2-580 M5X0.8 ISO Y CFT2-610 M6X1.0 ISO Y CFT2-8125 M8X1.25 ISO Y part numbering system CFT2-1015 M10X1.5 ISO Y CFT2-12175 M12X1.75 ISO Y
CFT/CAT Specifications Material: Stainless Steel, 304 L Steel, 12L14 Steel, 1215
HD ± .13
L ± .38
D Max.
MAT. THICK 0.76-2.29
5.36 6.83 7.77 10.16 HD 13.41 ± .13 14.94 5.36 20.32 6.83 7.77 5.36 10.16 6.83 13.41 7.77 14.94 10.16 20.32 13.41 14.94 5.36 20.32 6.83 7.77 10.16 13.41 14.94 20.32
9.40 9.40 9.40 13.08 L 15.62 ± .38 18.92 9.40 23.75 9.40 9.40 9.40 13.08 9.40 15.62 9.40 18.92 13.08 23.75 15.62 18.92 9.40 23.75 9.40 9.40 13.08 15.62 18.92 23.75
4.76 6.34 7.12 9.51 D 12.69 Max. 14.26 4.76 19.01 6.34 7.12 4.76 9.51 6.34 12.69 7.12 14.26 9.51 19.01 12.69 14.26 4.76 19.01 6.34 7.12 9.51 12.69 14.26 19.01
4.75 4.90 4.90 4.97 6.35 6.52 6.74 6.74 Recommended Hole Size 7.14 7.36 7.36+.13/-.00 7.54 9.80 MAT.9.52 THICK MAT.9.52 THICK MAT. THICK MAT.9.92 THICK 12.70 12.70 13.09 13.09 0.76-2.29 2.31-3.15 3.17-4.72 4.72-Over 14.68 14.28 14.28 14.68 4.75 4.90 4.90 4.97 19.83 20.24 19.05 19.44 6.35 6.52 6.74 6.74 7.14 7.36 7.36 7.54 4.75 4.90 4.90 4.97 9.52 9.52 9.80 9.92 6.35 6.52 6.74 6.74 12.70 12.70 13.09 13.09 7.14 7.36 7.36 7.54 14.28 14.28 14.68 14.68 9.80 9.92 9.52 9.52 19.05 19.44 19.83 20.24 12.70 12.70 13.09 13.09 14.28 14.28 14.68 14.68 4.75 4.90 4.90 4.97 19.05 19.44 19.83 20.24 6.35 6.52 6.74 6.74 7.14 7.36 7.36 7.54 9.52 9.52 9.80 9.92 12.70 12.70 13.09 13.09 14.28 14.28 14.68 14.68 19.05 19.44 19.83 20.24
CAT is Cadmium Plated per QQ-P-416 Type 1, Class 3 with clear protective coating
CFT is Proprietary Tin Plated
MAT. THICK 3.17-4.72
MAT. THICK 4.72-Over
Part Number Example: CAT2-2520
CAT Cadmium T series Featuring 3600 Swaging
Finish:
MAT. THICK 2.31-3.15
2 Material 1-Stainless Steel 2-Steel
2520 Thread Size
Special finish or material available upon request
*CFT and CAT rivet nut styles are dimensionally the same. CFT is Cadmium Free and RoHS Compliant. Actual hole size can be affected by parent material and material thickness. Contact Sherex for details. CFT/CAT series available in different finishes. Other specials available upon request. Contact Sherex for test data. INSTALLATION TOOLING CFT/CAT Series can be installed with our Hand Tools, Pneumatic Tools, and Hydro-Pneumatic Tools. For additional tooling information see pages 38-42. Sherex rivet nuts are compatible with the following hardware: GRADE 2, GRADE 5, CLASS 8.8 and CLASS 9.8 Please contact Sherex when using other grade fasteners.
12
Sherex Fastening Solutions
•
Request Info 1-800-453-1692 • Fax: 716-875-0358www.aboveboardelectronics.com • www.sherex.com • E-mail:
[email protected]
Phone: 866-474-3739
CPB PREBULBED SLOTTED BODY SERIES
CPB
series /— --.— IL---.Grip --7 HD _
7`-'------ime
I
1
/7/7/
HT-
L
Part Number Thread Size Grip Range HD L HT (Steel) Min. Max. Min. Max. ±.015 ±.005 CPB2-1024-175 10-24 UNC .020 .175 .490 .510 .828 .038 CPB2-1024-320 10-24Installs UNC into.175 .320 .490 .510 .921 .038 single, variable or multiple thickness materials. CPB2-1032-175 10-32 UNF .020 .175 .490 .510 .828 .038 CPB2-1032-320 10-32 UNF .175 .320 .490 .510 .921 .038 CPB2-2520-280 1/4-20 UNC .020 .280 .610 .645 1.000 .059 unified thread inches (unit CPB2-2520-500 1/4-20 UNC .280 - .500 .610 ).645 1.234 .059 CPB2-3118-280 5/16-18 UNC .020 .280 .740 1.141 .062 Part Number Thread Size Grip Range HD.770 L HT CPB2-3118-500 5/16-18 UNC .280 .500 .740 .770 1.375 .062 (Steel) Min. Max. Min. Max. ±.015 ±.005 CPB2-1024-175 CPB2-1024-320 CPB2-1032-175 CPB2-1032-320 CPB2-2520-280 CPB2-2520-500 CPB2-3118-280 CPB2-3118-500
10-24 UNC 10-24 UNC 10-32 UNF 10-32 UNF 1/4-20 UNC 1/4-20 UNC 5/16-18 UNC 5/16-18 UNC
metric thread Part Number (Steel) CPB2-580-4.45 CPB2-580-8.1 CPB2-610-7.1 CPB2-610-12.7 CPB2-8125-7.1 CPB2-8125-12.7
.020 .175 .020 .175 .020 .280 .020 .280
(unit -
Thread Size M5x0.8 ISO M5x0.8 ISO M6x1.0 ISO M6x1.0 ISO M8x1.25 ISO M8x1.25 ISO
.175 .320 .175 .320 .280 .500 .280 .500
.490 .490 .490 .490 .610 .610 .740 .740
.510 .510 .510 .510 .645 .645 .770 .770
IL Ref. .410 .410 .410 .410 .505 .505 .570 IL .570 Ref.
Hole Size +.006/-.000 .336 .336 .336 .336 .390 .390 .500 Hole Size .500 +.006/-.000
.038 .038 .038 .038 .059 .059 .062 .062
.329 .329 .329 .329 .382 .382 .495 .495
.410 .410 .410 .410 .505 .505 .570 .570
.336 .336 .336 .336 .390 .390 .500 .500
HT ±.0.13 0.96 0.96 1.50 1.50 1.57 1.57
D Max. 8.35 8.35 9.70 9.70 12.57 12.57
IL Ref. 10.00 10.00 12.80 12.80 14.48 14.48
Hole Size +.15/-.000 8.55 8.55 10.00 10.00 12.70 12.70
• The CPB series offers a large grip range for installation into single, variable or multiple thickness materials. • Large backside footprint provides increased pull out resistance. • Designed to be installed in thin plastics without distorting the base material.
millimeters)
Grip Range Min. Max. 0.50 4.45 4.45 8.10 0.50 7.10 7.10 12.70 0.50 7.10 7.10 12.70
HD Min. Max. 12.45 12.95 12.45 12.95 15.50 16.38 15.50 16.38 18.80 19.65 18.80 19.65
Thread Size Grip Range HD Part Number (Steel) Min. Max. Min. Max. CPB2-580-4.45 M5x0.8 ISO 0.50 4.45 12.45 12.95 part numbering CPB2-580-8.1 M5x0.8 ISO system 4.45 8.10 12.45 12.95 CPB2-610-7.1 M6x1.0 ISO 0.50 7.10 15.50 16.38 Part Number CPB Specifications CPB2-610-12.7 M6x1.0 ISO 7.10 12.70 15.50 16.38 Example: CPB2-2520-280 Material: Steel 1008/1010 CPB2-8125-7.1 Aluminum 5056 M8x1.25 ISO 0.50 7.10 18.80 19.65 CPB 12.70 18.80 CPB2-8125-12.7 2 19.65 M8x1.25 ISO 7.10 RoHS Compliant Finishes: Zinc Plated-Yellow Trivalent Chromate per Sherex SFS-01-001, SC2 Zinc Plated-Clear Trivalent Chromate per Sherex SFS-01-001
.828 .921 .828 .921 1.000 1.234 1.141 1.375
D Max. .329 .329 .329 .329 .382 .382 .495 D .495 Max.
Product Style Slotted Body Pre-bulbed
2-Steel 3-Aluminum
L ±.0.38 21.03 23.80 25.40 31.32 28.95 34.90
L HT D ±.0.38 ±.0.13 Max. 21.03 0.96 8.35 23.80 0.96 8.35 25.40 1.50 9.70 31.32 1.50 9.70 28.95 1.57 12.57 2520 34.90 1.57 280 12.57 Thread Size
IL Hole Size Ref. +.15/-.000 10.00 8.55 10.00 8.55 12.80 10.00 12.80 10.00 14.48 12.70 14.48 (_) 12.70
Grip Range
WEDGE HEAD
Empty-Open End T-Clear Trivalent W-Wedge Head TR-Trim Head
TRIM HEAD Special finish or material available upon request
Grip range can be affected by parent material and hole size. Sherex recommends trials installations to determine the proper grip range for the application. Contact Sherex for details. Contact Sherex for test data. INSTALLATION TOOLING CPB Series can be installed with our Hand Tools, Pneumatic Tools, and Hydro-Pneumatic Tools. For additional tooling information see pages 38-42. Sherex rivet nuts are compatible with the following hardware: GRADE 2, GRADE 5, CLASS 8.8 and CLASS 9.8 Please contact Sherex when using other grade fasteners.
Sherex Fastening Solutions
•
Request Info 1-800-453-1692 • Fax: 716-875-0358 www.aboveboardelectronics.com • www.sherex.com • E-mail:
[email protected]
Phone: 866-474-3739
13 SHERES f 1,91,111. SOLUTIOMS
71:
-I
CPN
CPN STRAIGHT SHANK SLOTTED BODY SERIES
series
° HD -
HT—
• The CPN series offers a large grip range for installation into single, variable or multiple thickness materials. • Large backside footprint provides increased pull out resistance. • Designed to be installed in thin plastics without distorting the base material. • Must be installed with spin-pull installation tooling.
Part Number Thread Size Grip Range HD L HT (Steel) Min. Max. Min. Max ± .015 ± .005 CPN2-1024-175 10-24 UNC .020 .175 .490 .510 .781 .038 Installs into single, variable, or multiple thickness materials. CPN2-1024-320 10-24 UNC .175 .320 .490 .510 .921 .038 CPN2-1032-175 10-32 UNF .020 .175 .490 .510 .781 .038 CPN2-1032-320 10-32 UNF .175 .320 .490 .510 .921 .038 CPN2-2520-280 1/4-20 UNC .020 .280 .610 .645 1.000 .059 unified thread (unit - inches) CPN2-2520-500 1/4-20 UNC .280 .500 .610 .645 1.234 .059 CPN2-3118-280 5/16-18 Size UNC Grip .020 Range .280 .740 HD.770 1.141 .062 Part Number Thread L HT CPN2-3118-500 .280 .500 .740 .770 1.375 5/16-18 UNC (Steel) Min. Max. Min. Max ± .015 ±.062 .005 CPN2-1024-175 CPN2-1024-320 CPN2-1032-175 CPN2-1032-320 CPN2-2520-280 CPN2-2520-500 CPN2-3118-280 CPN2-3118-500
10-24 UNC 10-24 UNC 10-32 UNF 10-32 UNF 1/4-20 UNC 1/4-20 UNC 5/16-18 UNC 5/16-18 UNC
metric thread
WEDGE HEAD
.020 .175 .020 .175 .020 .280 .020 .280
(unit -
Part Number (Steel)
Thread Size
CPN2-580-4.45 CPN2-580-8.1 CPN2-610-7.1 CPN2-610-12.7 CPN2-8125-7.1 CPN2-8125-12.7
M5x0.8 ISO M5x0.8 ISO M6x1.0 ISO M6x1.0 ISO M8x1.25 ISO M8x1.25 ISO
Part Number (Steel)
Thread Size
.175 .320 .175 .320 .280 .500 .280 .500
.490 .490 .490 .490 .610 .610 .740 .740
.510 .510 .510 .510 .645 .645 .770 .770
.781 .921 .781 .921 1.000 1.234 1.141 1.375
f
L
D Max. .272 .272 .272 .272 .346 .346 .437 D .437 Max.
IL Ref. .425 .425 .425 .425 .505 .505 .570 IL .570 Ref.
Hole Size +.006/-.000 .273 .273 .273 .273 .347 .347 .438 Hole Size .438 +.006/-.000
.038 .038 .038 .038 .059 .059 .062 .062
.272 .272 .272 .272 .346 .346 .437 .437
.425 .425 .425 .425 .505 .505 .570 .570
.273 .273 .273 .273 .347 .347 .438 .438
millimeters) HD Min. Max 12.45 12.95 12.45 12.95 15.50 16.38 15.50 16.38 18.80 19.65 18.80 19.65
L ± 0.38 21.03 23.80 25.40 31.32 28.95 34.90
HT ± .13 0.96 0.96 1.50 1.50 1.57 1.57
D Max. 7.47 7.47 8.79 8.79 11.10 11.10
IL Ref. 9.90 9.90 12.80 12.80 14.48 14.48
Hole Size +.15/-0.00 7.48 7.48 8.80 8.80 11.11 11.11
Grip Range HD Min. Max. Min. Max CPN2-580-4.45 M5x0.8 ISO 0.50 4.45 12.45 12.95 CPN2-580-8.1 M5x0.8 ISO 4.45 8.10 12.45 12.95 part numbering CPN2-610-7.1 M6x1.0 ISO system 0.50 7.10 15.50 16.38 CPN2-610-12.7 M6x1.0 ISO 7.10 12.70 15.50 16.38 Part Number CPN Specifications CPN2-8125-7.1 M8x1.25 ISO 0.50Example: 7.10CPN2-2520-280 18.80 19.65 Material: Steel 1008/1010 CPN2-8125-12.7 M8x1.25 ISO 7.10 12.70 18.80 19.65 Aluminum 5056
L ± 0.38 21.03 23.80 25.40 31.32 28.95 34.90
HT ± .13 0.96 0.96 1.50 1.50 1.57 1.57
D Max. 7.47 7.47 8.79 8.79 11.10 11.10
IL Ref. 9.90 9.90 12.80 12.80 14.48 14.48
Hole Size +.15/-0.00 7.48 7.48 8.80 8.80 11.11 11.11
RoHS Compliant Finishes: Zinc Plated-Yellow Trivalent Chromate per Sherex SFS-01-001, SC2 Zinc Plated-Clear Trivalent Chromate per Sherex SFS-01-001
Grip Range Min. Max. 0.50 4.45 4.45 8.10 0.50 7.10 7.10 12.70 0.50 7.10 7.10 12.70
CPN Product Style Slotted Body Straight Shank
2 2520 2-Steel Thread Size 3-Aluminum
280 Grip Range
(_) Empty-Open End T-Clear Trivalent W-Wedge Head
Special finish or material available upon request
Grip range can be affected by parent material and hole size. Sherex recommends trials installations to determine the proper grip range for the application. Contact Sherex for details. Contact Sherex for test data. CPN Series must be installed with spin pull tooling. For more information see pages 38-42. Sherex rivet nuts are compatible with the following hardware: Please contact Sherex when using other grade fasteners.
14
Request Info 1-800-453-1692 Sherex Fastening Solutions • Phone: 866-474-3739 • Fax: 716-875-0358www.aboveboardelectronics.com • www.sherex.com • E-mail:
[email protected]
CFH & CFHD FULL HEX BODY SERIES CFH SERIES
CFHD SERIES
HOLE
CFH/ CFHD series
' ea\ IIP -
THREAD SIZE •
cfh unified thread SHEREX SHEREX Part Number Part Number CFH2-1024-085 CFH2-1024-085 CFH2-1024-135 CFH2-1024-135 CFH2-1024-185 CFH2-1024-185 CFH2-1032-085 CFH2-1032-085 CFH2-1032-135 CFH2-1032-135 CFH2-1032-185 CFH2-1032-185 CFH2-2520-085 CFH2-2520-085 CFH2-2520-145 CFH2-2520-145 CFH2-2520-205 CFH2-2520-205 CFH2-3118-105 CFH2-3118-105 CFH2-3118-175 CFH2-3118-175 CFH2-3118-245 CFH2-3118-245 CFH2-3716-115 CFH2-3716-115 CFH2-3716-205 CFH2-3716-205 CFH2-3716-295 CFH2-3716-295
Thread Size Thread Size 10-24 UNC 10-24 UNC UNC 10-24 10-24 UNC UNC 10-24 10-24 UNC 10-32 UNF 10-32 UNF UNF 10-32 10-32 UNF UNF 10-32 10-32 UNF 1/4-20 UNC 1/4-20 UNC UNC 1/4-20 1/4-20 UNC 1/4-20 UNC 1/4-20 UNC 5/16-18 UNC 5/16-18 UNC UNC 5/16-18 5/16-18 UNC 5/16-18 UNC 5/16-18 UNC 3/8-16 UNC 3/8-16 UNC 3/8-16 UNC 3/8-16 UNC UNC 3/8-16 3/8-16 UNC
Grip Range Grip Range Min. Max. Min. Max. .010 .085 .010 .085 .085 .135 .085 .135 .135 .185 .135 .185 .010 .085 .010 .085 .085 .135 .085 .135 .135 .185 .135 .185 .020 .085 .020 .085 .085 .145 .085 .145 .145 .205 .145 .205 .030 .105 .030 .105 .105 .175 .105 .175 .175 .245 .175 .245 .030 .115 .030 .115 .115 .205 .115 .205 .205 .295 .205 .295
cfh metric thread SHEREX SHEREX Part Number Part Number CFH2-580-2.1 CFH2-580-2.1 CFH2-580-3.5 CFH2-580-3.5 CFH2-580-5.0 CFH2-580-5.0 CFH2-610-2.1 CFH2-610-2.1 CFH2-610-3.6 CFH2-610-3.6 CFH2-610-5.2 CFH2-610-5.2 CFH2-8125-2.5 CFH2-8125-2.5 CFH2-8125-4.5 CFH2-8125-4.5 CFH2-8125-6.6 CFH2-8125-6.6 CFH2-1015-2.9 CFH2-1015-2.9 CFH2-1015-5.2 CFH2-1015-5.2 CFH2-1015-7.5 CFH2-1015-7.5
Thread Size Thread Size M5x0.8 ISO M5x0.8 ISO ISO M5x0.8 M5x0.8 ISO M5x0.8 ISO M5x0.8 ISO ISO M6x1.0 M6x1.0 ISO M6x1.0 ISO M6x1.0 ISO ISO M6x1.0 M6x1.0 M8x1.25 ISO ISO M8x1.25 ISO M8x1.25 ISO M8x1.25 ISO ISO M8x1.25 M8x1.25 ISO M10x1.50 ISO M10x1.50 ISO ISO M10x1.50 M10x1.50 ISO M10x1.50 ISO M10x1.50 ISO
(unit -
cfhd unified thread SHEREX SHEREX Part Number Part Number CFHD2-2520-080 CFHD2-2520-080 CFHD2-2520-150 CFHD2-2520-150 CFHD2-3118-100 CFHD2-3118-100 CFHD2-3118-180 CFHD2-3118-180 CFHD2-3716-125 CFHD2-3716-125 CFHD2-3716-230 CFHD2-3716-230
inches)
HD Min. HDMax. Min. Max. .329 .359 .329 .359 .329 .359 .329 .359 .359 .329 .329 .359 .329 .359 .329 .359 .359 .329 .329 .359 .359 .329 .329 .452 .359 .422 .422 .452 .452 .422 .422 .452 .422 .452 .422 .452 .547 .577 .547 .577 .577 .547 .547 .577 .547 .577 .547 .671 .577 .641 .641 .671 .641 .671 .641 .671 .671 .641 .641 .671
(unit -
Grip Range Grip Range Min. Max. Min. Max. 0.50 2.15 0.50 2.15 2.15 3.55 2.15 3.55 3.55 5.05 3.55 5.05 0.50 2.15 0.50 2.15 2.15 3.65 2.15 3.65 3.65 5.20 3.65 5.20 0.50 2.55 0.50 2.55 2.50 4.55 2.50 4.55 4.55 6.60 4.55 6.60 0.75 2.95 0.75 2.95 2.95 5.20 2.95 5.20 5.20 7.50 5.20 7.50
L L ± .015 ± .015 .344 .344 .406 .406 .453 .453 .344 .344 .406 .406 .453 .453 .406 .406 .469 .469 .531 .531 .562 .562 .640 .640 .703 .703 .625 .625 .718 .718 .812 .812
HT D (A/F) IL (A/F) Ref. HT DMax. IL Nom. Nom. Max. Ref. .043 .223 .200 .043 .223 .200 .043 .223 .210 .043 .223 .210 .210 .043 .223 .043 .223 .210 .043 .223 .200 .043 .223 .200 .043 .223 .210 .043 .223 .210 .043 .223 .210 .043 .223 .210 .043 .296 .250 .043 .296 .250 .043 .296 .250 .043 .296 .250 .043 .296 .250 .043 .296 .250 .048 .368 .375 .048 .368 .375 .048 .368 .380 .048 .368 .380 .048 .368 .375 .048 .368 .375 .058 .437 .400 .058 .437 .400 .058 .437 .405 .058 .437 .405 .058 .437 .410 .058 .437 .410
Hole Size (A/F) Hole Size (A/F)
+.005/-.000 +.005/-.000 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .224 .297 .297 .297 .297 .297 .297 .369 .369 .369 .369 .369 .369 .438 .438 .438 .438 .438 .438
• The CFH series offers a full hexagonal body for exceptional spin out resistance.
millimeters)
L HD L Min. HDMax. ± .38 Min. Max. ± .38 9.14 9.90 10.30 9.14 9.90 9.90 10.30 9.14 11.90 9.14 9.90 11.90 9.14 9.90 13.48 9.14 9.90 13.48 10.71 11.47 10.30 10.71 11.47 11.47 11.90 10.30 10.71 10.71 11.47 11.47 13.48 11.90 10.71 10.71 11.47 13.48 14.69 15.45 15.86 14.69 15.45 15.86 14.69 15.45 17.84 14.69 15.45 15.45 19.82 17.84 14.69 14.69 15.45 19.82 17.10 17.86 15.88 17.10 17.86 17.86 18.24 15.88 17.10 17.10 17.86 18.24 17.10 17.86 20.62 17.10 17.86 20.62
(unit -
Grip Range Thread Size Grip Range Thread Size Min. Max. Min. Max. 1/4-20 UNC .020 .080 1/4-20 UNC .020 .080 1/4-20 UNC .080 .150 1/4-20 UNC .080 .150 5/16-18 UNC .020 .100 5/16-18 UNC .020 .100 5/16-18 UNC .100 .180 5/16-18 UNC .100 .180 3/8-16 UNC .020 .125 3/8-16 UNC .020 .125 3/8-16 UNC .125 .230 3/8-16 UNC .125 .230
;
HT D (A/F) IL Hole Size (A/F) Hole Size (A/F) (A/F) IL HT DMax. Nom. Ref. +.13/-.000 Nom. Max. Ref. +.13/-.000 1.09 6.35 6.72 6.35 1.09 6.35 6.72 6.35 1.09 6.35 6.72 6.35 1.09 6.35 6.72 6.35 1.09 6.35 6.72 6.35 1.09 6.35 6.72 6.35 1.09 7.51 6.22 7.51 1.09 7.51 6.22 7.51 1.09 7.51 6.22 7.51 1.09 7.51 6.22 7.51 1.09 7.51 6.22 7.51 1.09 10.08 7.51 10.35 6.22 7.51 1.57 10.08 1.57 10.08 10.35 10.08 1.57 10.08 10.35 10.08 1.57 10.08 10.35 10.08 1.57 10.08 10.35 10.08 1.57 10.08 10.35 10.08 1.57 11.89 13.08 11.89 1.57 11.89 11.89 13.08 11.89 1.57 13.08 11.89 1.57 11.89 11.89 13.08 11.89 1.57 13.08 11.89 1.57 11.89 13.08 11.89
inches)
HD HD Min. Max. Min. Max. .454 .484 .454 .484 .454 .484 .454 .484 .579 .609 .579 .609 .579 .609 .579 .609 .673 .703 .673 .703 .673 .703 .673 .703
L L ± .015 ± .015 .500 .500 .578 .578 .625 .625 .703 .703 .703 .703 .812 .812
HT D (A/F) IL HT D (A/F) IL Nom. Max. Ref. Nom. Max. Ref. .058 .312 .340 .058 .312 .340 .058 .312 .345 .058 .312 .345 .062 .397 .405 .062 .397 .405 .062 .397 .405 .062 .397 .405 .088 .468 .450 .088 .468 .450 .088 .468 .450 .088 .468 .450
Hole Size (A/F) Hole Size (A/F)
+.010/-.000 +.010/-.000 .312 .312 .312 .312 .397 .397 .397 .397 .468 .468 .468 .468
• The CFHD series offers the same benefits as the CFH series but with higher strength.
part numbering system CFH/CFHD Specifications
Material: Steel 1008/1010 Stainless Steel 302 Aluminum 5056
RoHS Compliant Finishes: Zinc Plated-Yellow Trivalent Chromate per Sherex SFS-01-001, SC2 Zinc Plated-Clear Trivalent Chromate per Sherex SFS-01-001
Part Number Example: CFH2-2520-085 CFH Full Hex Heavy Duty Large Flange CFHD - High Strength
Sherex rivet nuts are compatible with the following hardware:
Sherex Fastening Solutions
•
2 2520 Material Thread Size 1-Stainless Steel 2-Steel 3-Aluminum
085 Grip Range
(_) Empty-Open End B-Closed End
Special finish or material available upon request GRADE 2, GRADE 5, CLASS 8.8 and CLASS 9.8 Please contact Sherex when using other grade fasteners.
Phone: 866-474-3739 716-875-0358 • Fax:Info Request
•
www.sherex.com
•
E-mail:
[email protected]
1-800-453-1692 www.aboveboardelectronics.com
15
METRIC BODY STYLE Rivet Nuts
METRIC BODY STYLE RIVET NUTS
• Metric body styles are designed to be placed into metric drilled or punched holes. • Many of the metric body styles are available with inch/imperial thread. • The products are manufactured in our ISO/TS 16949 certified production facility or by our Belgium partner, Dejond. • Special designs are available to meet customer specific requirements. Contact Sherex with your application information.
catalog attributes
-
metric body style
Grip Range(E) Material Thickness L Length D Head Diameter K Head Thickness
d Diameter d(A/F) Diameter Across Flats b Hole Size
I
16
S
Sherex Fastening Solutions
•
Request Info 1-800-453-1692 • Fax: 716-875-0358www.aboveboardelectronics.com • www.sherex.com • E-mail:
[email protected]
Phone: 866-474-3739
UPO LARGE FLANGE METRIC SERIES
UPO series
xl
metric thread
(unit -
millimeters)
Grip Range (E)
Part Number Steel
Thread Size
TU-SM3UPO20ZT TU-SM3UPO30ZT TU-SM4UPO30ZT TU-SM4UPO45ZT TU-SM5UPO30ZT TU-SM5UPO55ZT TU-SM6UPO30ZT TU-SM6UPO55ZT TU-SM6UPO80ZT TU-SM8UPO30ZT TU-SM8UPO55ZT TU-SM8UPO80ZT TU-SM10UPO35ZT TU-SM10UPO60ZT TU-SM10SPO35ZT TU-SM10SPO60ZT TU-SM12UPO40ZT TU-SM12UPO70ZT
M3X0.5 ISO M3X0.5 ISO M4X0.7 ISO M4X0.7 ISO M5X0.8 ISO M5X0.8 ISO M6X1.0 ISO M6X1.0 ISO M6X1.0 ISO M8X1.25 ISO M8X1.25 ISO M8X1.25 ISO M10X1.5 ISO M10X1.5 ISO M10X1.5 ISO M10X1.5 ISO M12X1.75 ISO M12X1.75 ISO
Min.
Max.
L ± 0.35
0.5 2.0 0.5 3.0 0.5 3.0 0.5 3.0 5.5 0.5 3.0 5.5 0.8 3.5 0.8 3.5 1.0 4.0
2.0 3.0 3.0 4.5 3.0 5.5 3.0 5.5 8.0 3.0 5.5 8.0 3.5 6.0 3.5 6.0 4.0 7.0
9.8 10.8 10.8 12.3 12.0 15.0 14.5 16.5 19.0 16.0 18.5 21.5 19.8 22.8 21.0 24.0 25.0 28.0
D ± 0.35
K ± 0.15
d -0.02/-0.15
Hole Size (b+0.1)
8.0
0.8
5.0
5.1
10.0
0.8
6.0
6.0
11.0
1.0
7.0
7.0
13.0
1.5
9.0
9.0
16.0
1.5
11.0
11.0
18.5
2.3
12.4
12.5
19.0
2.0
13.0
13.0
23.0
2.0
16.0
16.0
• The UPO series offers a large flange for increased strength and better containment of round or oversized holes. • The metric body dimensions allow for use in metric holes.
Material: Steel QST 34-3 Stainless Steel 304 Cu part numbering system Stainless Steel 316 Cu UPO Specifications Aluminum ALMG 2.5 Part Number Material
Example: TU-SM5UPO30ZT
Steel QST 34-3 RoHs Compliant Finish: Stainless Cu r TU Zinc Top,Steel 96 w304 / 480 Stainless Steel 316 Cu Aluminum ALMG 2.5
Product Style Metric
RoHs Compliant Finish: Zinktop (Clear), 96 w / 480 r
S M5 Material Thread Size S-Steel A-Aluminum SS-304 Stainless Steel *316-316 Stainless Steel
O UP O-Open End Product Type Large Flange, Flat Head X-Closed End Metric Body
30 Grip Range
ZT Zinktop (Clear)
Special finish or material available upon request
*316 Stainless Steel has extra corrosion resistance and can be used in the medical, chemical and food industries. Grip Range can be affected by parent material and hole size. Sherex recommends trial installations to determine the proper grip range for the application. Closed End sizes available: M4, M5, M6, and M8. Also available with imperial threads - minimum order quantity is 25,000 pieces if not in stock. Contact Sherex for test data. INSTALLATION TOOLING UPO Series can be installed with our Hand Tools, and Hydro-Pneumatic Tools. For additional tooling information see pages 38-42.
All Parts have been manufactured by:
DEJON10
TUBTARA®- A DEJOND PRODUCT Sherex rivet nuts are compatible with the following hardware: GRADE 2, GRADE 5, CLASS 8.8 and CLASS 9.8 Please contact Sherex when using other grade fasteners. Sherex Fastening Solutions
•
Phone: 866-474-3739 716-875-0358 • Fax: Request Info
•
www.sherex.com
E-mail:
[email protected] • 1-800-453-1692
www.aboveboardelectronics.com
17
UFO/ UKO
UFO COUNTERSUNK HEAD & UKO SMALL FLANGE METRIC SERIES UFO SERIES
series
metric thread
• The UFO series offers a contersunk head for flush installation into the parent materials. • The metric body dimensions allow for use in metric holes.
• The UKO series offers a small flange head for near flush installation. • The metric body dimensions allow for use in metric size holes.
UKO SERIES
(unit -
Part Number Steel
Thread Size
TU-SM3UFO35ZT TU-SM4UFO35ZT TU-SM4UFO50ZT TU-SM5UFO40ZT TU-SM5UFO65ZT TU-SM6UFO45ZT TU-SM6UFO65ZT TU-SM8UFO45ZT TU-SM8UFO65ZT TU-SM10UFO45ZT TU-SM10UFO65ZT TU-SM12UFO45ZT TU-SM12UFO75ZT
M3X0.5 ISO M4X0.7 ISO M4X0.7 ISO M5X0.8 ISO M5X0.8 ISO M6X1.0 ISO M6X1.0 ISO M8X1.25 ISO M8X1.25 ISO M10X1.5 ISO M10X1.5 ISO M12X1.75 ISO M12X1.75 ISO
millimeters)
Grip Range (E) Min.
Max.
OL ± 0.35
D +0.00/-0.5
K +0.3/-0.05
d -0.02/-0.15
Hole Size (b+0.1)
1.7 1.7 3.5 1.7 4.0 1.7 4.5 1.7 4.5 1.7 4.5 2.0 4.5
3.5 3.5 5.0 4.0 6.5 4.5 6.5 4.5 6.5 4.5 6.5 4.5 7.5
11.25 11.5 13.0 13.0 16.0 17.0 19.0 19.0 21.0 21.0 23.0 26.0 29.0
8.0
1.5
5.0
5.1
9.0
1.5
6.0
6.0
10.0
1.5
7.0
7.0
12.0
1.5
9.0
9.0
14.0
1.5
11.0
11.0
15.4
1.5
12.4
12.5
19.0
1.8
16.0
16.0
metric thread (unit - millimeters) Material: Steel QST 34-3 Grip Range (E) Part Number OL D Stainless Steel 304 Cu Thread Size Steel ± 0.35 +0.3/-0.15 Min. Max. Aluminum ALMG 2.5 TU-SM4UKO30ZT M4X0.7 ISO 0.5 3.0 10.75 6.5 TU-SM5UKO30ZT M5X0.8 ISO 0.5 3.0 12.0 RoHs Compliant Finish: 7.5 Zinc Top, 96 w / 480 r M5X0.8 ISO TU-SM5UKO55ZT 3.0 5.5 15.0 TU-SM6UKO30ZT M6X1.0 ISO 0.5 3.0 14.5 9.5 TU-SM6UKO55ZT M6X1.0 ISO 3.0 5.5 16.5 TU-SM8UKO30ZT M8X1.25 ISO 0.5 3.0 16.0 11.5 TU-SM8UKO55ZT M8X1.25 ISO 3.0 5.5 18.5 TU-SM10UKO35ZT M10X1.5 ISO 0.8 3.5 19.5 12.9
K +0.3/-0.05
d -0.02/-0.15
Hole Size (b+0.1)
0.5
6.0
6.0
0.5
7.0
7.0
0.5
9.0
9.0
0.5
11.0
11.0
0.5
12.4
12.5
part Material:numbering system
Steel 34-3 UFOQST Specifications Material:Steel 304 Cu Stainless Steel QSTSteel 34-3 316 Cu Stainless Stainless Steel 304 Cu Aluminum 2.5 AluminumALMG ALMG 2.5
Part Number Example: TU-SM5UFO35ZT TU Product Style: Metric
RoHsCompliant Compliant Finish: RoHs Finish: Zinktop w / r480 r Zinc Top,(Clear), 96 w /96 480 UKO Specifications Material: Steel QST 34-3 Stainless Steel 304 Cu Stainless Steel 316 Cu Aluminum ALMG 2.5
S M5 Material Thread Size S-Steel A-Aluminum SS-304 Stainless Steel
UF Product Type Smooth Shank Countersunk Head Metric Body
O O-Open End X-Closed End
35 Grip range
ZT Zinktop (Clear)
UK O 30 O-Open End Grip range Product Type X-Closed End Smooth Shank Small Flange, Round Body Metric Body
ZT Zinktop (Clear)
Part Number Example: TU-SM5UKO30ZT TU Product Style: Metric
RoHs Compliant Finish: Zinktop (Clear), 96 w / 480 r
S M5 Material Thread Size S-Steel A-Aluminum SS-304 Stainless Steel *316-316 Stainless Steel
Special finish or material available upon request
*316 Stainless Steel has extra corrosion resistance and can be used in the medical, chemical and food industries Grip Range can be affected by parent material and hole size. Sherex recommends trial installations to determine the proper grip range for the application. RoHS Compliant Trivalent Plating available upon request. Closed End sizes available: M4, M5, M6, M8. Also available with imperial threads - minimum order quantity is 25,000 pieces if not in stock. Contact Sherex for test data.
INSTALLATION TOOLING HUPO/HUKO Series can be installed with our Hand Tools and Hydro-Pneumatic Tools. For additional tooling information see pages 38-42.
18 SHEREI FASITIVIIC 501,1110149
Sherex Fastening Solutions
•
All Parts have been manufactured by:
TUBTARA®- A DEJOND PRODUCT Sherex rivet nuts are compatible with the following hardware: GRADE 2, GRADE 5, CLASS 8.8 and CLASS 9.8 Please contact Sherex when using other grade fasteners.
Request Info 1-800-453-1692 • Fax: 716-875-0358www.aboveboardelectronics.com • www.sherex.com • E-mail:
[email protected]
Phone: 866-474-3739
HUPO & HUKO LARGE AND SMALL FLANGE HEXAGONAL METRIC SERIES HUPO SERIES
HUKO SERIES
hupo metric thread Part Number PartSteel Number Steel TU-SM4HUPO20ZT
Thread Size
TU-SM5HUPO30ZT TU-SM4HUPO20ZT TU-SM6HUPO30ZT TU-SM5HUPO30ZT TU-SM6HUPO55ZT TU-SM6HUPO30ZT TU-SM8HUPO30ZT TU-SM6HUPO55ZT TU-SM8HUPO55ZT TU-SM8HUPO30ZT TU-SM8HUPO80ZT TU-SM8HUPO55ZT TU-SM10HSPO35ZT TU-SM8HUPO80ZT TU-SM10HSPO60ZT TU-SM10HSPO35ZT *TU-SM12HUPO40ZT TU-SM10HSPO60ZT
Thread Size M4X0.7 ISO M5X0.8 M4X0.7 ISO ISO M6X1.0 ISO ISO M5X0.8 M6X1.0 M6X1.0 ISO ISO M8X1.25 ISO M6X1.0 ISO M8X1.25 M8X1.25 ISO ISO M8X1.25 M8X1.25 ISO ISO M10X1.5 M8X1.25 ISO ISO M10X1.5 M10X1.5 ISO ISO M12X1.75 ISO M10X1.5 ISO
*TU-SM12HUPO40ZT
M12X1.75 ISO
(unit -
Grip Range (E) Grip (E) Min. RangeMax. Min. 0.5 0.5 0.5 0.5 0.5 3.0 0.5 0.5 3.0 3.0 0.5 5.5 3.0 0.8 5.5 3.5 0.8 1.0 3.5
Max. 2.0 3.0 2.0 3.0 3.0 5.5 3.0 3.0 5.5 5.5 3.0 8.0 5.5 3.5 8.0 6.0 3.5 4.0 6.0
1.0
4.0
huko metric thread unit Grip(Range (E) Part Number PartSteel Number
Steel TU-SM4HUKO20ZT TU-SM5HUKO30ZT TU-SM4HUKO20ZT TU-SM5HUKO55ZT TU-SM5HUKO30ZT TU-SM6HUKO30ZT TU-SM5HUKO55ZT TU-SM6HUKO55ZT TU-SM6HUKO30ZT TU-SM8HUKO30ZT TU-SM6HUKO55ZT TU-SM8HUKO55ZT TU-SM8HUKO30ZT TU-SM10HUKO35ZT TU-SM8HUKO55ZT
Thread Size
Thread Size M4X0.7 ISO M5X0.8 ISO M4X0.7 ISO M5X0.8 ISO ISO M5X0.8 M6X1.0 ISO ISO M5X0.8 M6X1.0 ISO ISO M6X1.0 M8X1.25 ISO M6X1.0 ISO M8X1.25 M8X1.25 ISO ISO M10X1.5 M8X1.25 ISO ISO
-
L ± 0.35 L ±10.0 0.35
D ± 0.35 D ± 9.0 0.35
K ± 0.15 K ± 1.0 0.15
d (A/F) -0.02/-0.15 d (A/F) -0.02/-0.15 6.0
13.0 10.0 14.5 13.0 16.5 14.5 16.5 16.5 19.0 16.5 22.0 19.0 21.0 22.0 23.5 21.0 25.0 23.5
10.0 9.0 10.0 13.0
1.0 1.0 1.0 1.5
7.0 6.0 7.0 9.0
13.0
1.5
9.0
9.0
16.0
1.5
11.0
11.0
16.0
1.5
11.0
11.0
19.0
2.0
13.0
13.0
19.0 23.0
2.0 2.0
13.0 16.0
13.0 16.0
25.0
23.0
2.0
16.0
16.0
D +0.3/-0.15 D +0.3/-0.15 6.6
K +0.3/-0.05 K +0.3/-0.05 0.6
d (A/F) -0.02/-0.15 d (A/F) -0.02/-0.15 6.0
Hole Size (b+0.1) Hole Size (b+0.1) 6.0
6.6 7.7
0.6 0.6
6.0 7.0
6.0 7.0
7.7 9.8
0.6 0.7
7.0 9.0
7.0 9.0
9.8 11.8
0.7 0.7
9.0 11.0
9.0 11.0
11.8 13.8
0.7 0.7
11.0 13.0
11.0 13.0
13.8
0.7
13.0
13.0
millimeters)
OL ± OL 0.35
Min. 0.5 0.5 0.5 3.0 0.5 0.5 3.0 3.0 0.5 0.5 3.0 3.0 0.5 0.8 3.0
±11.0 0.35 14.0 11.0 16.5 14.0 16.0 16.5 18.5 16.0 18.0 18.5 20.5 18.0 23.0 20.5
TU-SM10HUKO35ZT M10X1.5 ISO 0.8 3.5 Material: Steel QST 34-3 Material: Stainless 304 Cu Steel QSTSteel 34-3 part numbering system Stainless Stainless Steel Steel 316 304 Cu Cu Stainless Steel 316 Cu HUPO/HUKO Specifications RoHs Compliant Finish: Zinc Top, 96 w / 480 r RoHs Compliant Finish: Material: Zinc Top, 9634-3 w / 480 r Steel QST Stainless Steel 304 Cu Stainless Steel 316 Cu
millimeters)
Grip (E) Min. RangeMax. Max. 2.0 3.0 2.0 5.5 3.0 3.0 5.5 5.5 3.0 3.0 5.5 5.5 3.0 3.5 5.5
Part Number Example: TU-SM5HUPO30ZT TU Product Style Metric
RoHs Compliant Finish: Zinktop (Clear), 96 w / 480 r
23.0
Hole Size (b+0.1) Hole Size (b+0.1) 6.0 7.0 6.0 7.0 9.0
**All Stainless Steel are Semi-Hexagonal **All Stainless Steel are Semi-Hexagonal
M5 S Thread Size Material S-Steel SS-304 Stainless Steel *316-316 Stainless Steel
Part Number Example: TU-SM5HUKO30ZT M5 S Thread Size Material S-Steel SS-304 Stainless Steel Special finish or material available upon request *316-316 Stainless Steel All Stainless Steel parts are semi-hexagonal shank. TU Product Style Metric
HUPO/ HUKO series
HUP O 30 Product Type O-Open End Grip Range ZT Large Flange X-Closed End Zinktop (Clear) Flat Head Hexagonal Shank Metic Body *Semi-Hexagonal Shank
• The HUPO series has a large flange that provides increased strength. • Hexagonal shank body for improved spin out. • The metric body dimensions allow for use in metric holes.
• The HUKO series has a smaller flange head that gives a near flush installation into the parent material. • Hexagonal shank body for improved spin out. • The metric body dimensions allow for use in metric holes.
HUK O 30 Product Type O-Open End Grip Range ZT Small Flange X-Closed End Zinktop (Clear) Round Body Hexagonal Shank Metric Body
*316 Stainless Steel has extra corrosion resistance and can be used in the medical, chemical and food industries Grip Range can be affected by parent material and hole size. Sherex recommends trial installations to determine the proper grip range for the application. RoHS Compliant Trivalent Plating available upon request. Closed End sizes available: M4, M5, M6, M8. Also available with imperial threads - minimum order quantity is 25,000 pieces if not in stock. Contact Sherex for test data.
INSTALLATION TOOLING HUPO/HUKO Series can be installed with our Hand Tools and Hydro-Pneumatic Tools. For additional tooling information see pages 38-42. TUBTARA®- A DEJOND PRODUCT All Parts have been manufactured by: DEJOND Sherex rivet nuts are compatible with the following hardware: GRADE 2, GRADE 5, CLASS 8.8 and CLASS 9.8 Please contact Sherex when using other grade fasteners.
Request Info 1-800-453-1692 Sherex Fastening Solutions • Phone: 866-474-3739 • Fax: 716-875-0358 •www.aboveboardelectronics.com www.sherex.com • E-mail:
[email protected]
19
UPO RS/ UFO RS
UPO RS & UFO RS LARGE AND COUNTERSUNK KNURLED METRIC SERIES UPO RS SERIES
series
UFO RS SERIES
upo rs metric thread
• The UPO RS series has a large flange that provides increased strength and better containment of round or oversized holes. • Unique knurling increases spin out resistance in soft materials.
• The UFO RS has a countersunk head style for flush installations. • Unique knurling increases spin out resistance.
Part Number Steel
Thread Size
Part Number TU-SM4UPO30RZT Steel TU-SM4UPO45RZT TU-SM5UPO30RZT TU-SM4UPO30RZT TU-SM5UPO55RZT TU-SM4UPO45RZT TU-SM6UPO30RZT TU-SM5UPO30RZT TU-SM6UPO55RZT TU-SM5UPO55RZT TU-SM8UPO30RZT TU-SM6UPO30RZT TU-SM8UPO55RZT TU-SM6UPO55RZT TU-SM10UPO35RZT TU-SM8UPO30RZT TU-SM10UPO60RZT TU-SM8UPO55RZT
M4X0.7 ISO Thread Size M4X0.7 ISO M5X0.8 ISO M4X0.7 ISO M5X0.8 ISO M4X0.7 ISO M6X1.0 M5X0.8 ISO ISO M6X1.0 M5X0.8 ISO ISO M8X1.25 ISO M6X1.0 ISO M8X1.25 ISO M6X1.0 ISO M10X1.5 ISO M8X1.25 ISO M10X1.5 ISO ISO M8X1.25
(unit -
Grip Range (E) Min. Max. Grip (E) 0.5 Range3.0 Min. 3.0 0.5 0.5 3.0 3.0 0.5 0.5 3.0 3.0 0.5 0.5 3.0 3.0 0.8 0.5 3.5 3.0
Max. 4.5 3.0 3.0 5.5 4.5 3.0 3.0 5.5 5.5 3.0 3.0 5.5 5.5 3.5 3.0 6.0 5.5
TU-SM10UPO35RZT M10X1.5 ISO 0.8 3.5 Grip Range (E) Part Number TU-SM10UPO60RZT M10X1.5 ISO 3.5 6.0 Thread Size ufo rs Steel metric thread Min. (unit Max. Grip (E) Part Number TU-SM4UFO35RZT M4X0.7 ISO 1.7 Range3.5 Thread Size Steel Min. Max. TU-SM4UFO50RZT M4X0.7 ISO 3.5 5.0 TU-SM5UFO40RZT M5X0.8 ISO 1.7 4.0 TU-SM4UFO35RZT M4X0.7 ISO 1.7 3.5 TU-SM5UFO65RZT M5X0.8 ISO 4.0 6.5 TU-SM4UFO50RZT M4X0.7 ISO 3.5 5.0 TU-SM6UFO45RZT M6X1.0 1.7 4.5 TU-SM5UFO40RZT M5X0.8 ISO ISO 1.7 4.0 TU-SM6UFO65RZT M6X1.0 ISO 4.5 6.5 TU-SM5UFO65RZT M5X0.8 ISO 4.0 6.5 TU-SM8UFO45RZT M8X1.25 ISO 1.7 4.5 TU-SM6UFO45RZT M6X1.0 ISO 1.7 4.5 TU-SM8UFO65RZT M8X1.25 ISO 4.5 6.5 TU-SM6UFO65RZT M6X1.0 ISO 4.5 6.5 TU-SM10UFO45RZT M10X1.5 ISO ISO 1.7 4.5 TU-SM8UFO45RZT M8X1.25 1.7 4.5 TU-SM10UFO65RZT M10X1.5 ISO ISO 4.5 6.5 TU-SM8UFO65RZT M8X1.25 4.5 6.5 TU-SM10UFO45RZT Material: TU-SM10UFO65RZT Steel QST 34-3
M10X1.5 ISO M10X1.5 ISO
1.7 4.5
4.5 6.5
-
millimeters) L ± 0.35
D ± 0.35
K ± 0.15
d -0.02/-0.15
Hole Size (b+0.1)
L 10.75 ±12.25 0.35 12.0 10.75 15.0 12.25 14.5 12.0 16.5 15.0 16.0 14.5 18.5 16.5 19.75 16.0 22.75 18.5
D 10.0 ± 0.35
K 0.75 ± 0.15
d 6.3 -0.02/-0.15
Hole Size 6.4 (b+0.1)
11.0 10.0
1.0 0.75
7.3 6.3
7.4 6.4
13.0 11.0
1.5 1.0
9.3 7.3
9.4 7.4
16.0 13.0
1.5 1.5
11.4 9.3
11.5 9.4
18.5 16.0
2.25 1.5
12.9 11.4
13.0 11.5
19.75 18.5 2.25 L D K 22.75 millimeters ) ± 0.35 +0.00/-0.5 +0.3/-0.05
12.9 d -0.02/-0.15
13.0 Hole Size (b+0.1)
D K 9.0 1.5 +0.00/-0.5 +0.3/-0.05
d 6.3 -0.02/-0.15
Hole Size 6.4 (b+0.1)
L 11.5 ±13.0 0.35 13.0 11.5 16.0 13.0 17.0 13.0 19.0 16.0 19.0 17.0 21.0 19.0 21.0 19.0 23.0 21.0 21.0 23.0
10.0 9.0
1.5 1.5
7.3 6.3
7.4 6.4
12.0 10.0
1.5 1.5
9.3 7.3
9.4 7.4
14.0 12.0
1.5 1.5
11.4 9.3
11.5 9.4
15.4 14.0
1.5 1.5
12.9 11.4
13.0 11.5
15.4
1.5
12.9
13.0
Material: RoHs Compliant Finish: Steel QST 34-3 Zinc Top, 96 w / 480 r
part numbering system RoHs Compliant Finish: UPO RS/UFO Specifications Zinc Top, 96 wRS / 480 r Material: Steel QST 34-3 RoHs Compliant Finish: Zinktop (Clear), 96 w / 480 r
Part Number Example: TU-SM5UPO30RZT TU S M5 UP O 30 Product Style: Material Thread Size Product Type O-Open End Grip Metric S-Steel Large Flange, Flat Head Metic Body Part Number Example: SM5UFO40RZT
R Ribbed
ZT Zinktop (Clear)
S M5 UF TU ZT O R 30 Product Style: Material Thread Size Product Type O-Open End Grip Ribbed Zinktop (Clear) S-Steel Smooth Shank Metric Countersunk Head Metric Body Special finish or material available upon request Grip Range can be affected by parent material and hole size. Sherex recommends trial installations to determine the proper grip range for the application. RoHS Compliant Trivalent Plating available upon request. Also available with imperial threads - minimum order quantity is 25,000 pieces if not in stock. Contact Sherex for test data.
20
INSTALLATION TOOLING UPO RS/ UFO RS Series can be installed with our Hand Tools and Hydro-Pneumatic Tools. For additional tooling information see pages 38-42. TUBTARA®- A DEJOND PRODUCT Sherex rivet nuts are compatible with the following hardware: All Parts have been manufactured by: GRADE 2, GRADE 5, CLASS 8.8 and CLASS 9.8 Please contact Sherex when using other grade fasteners.
DEJOND
Request Info 1-800-453-1692 Sherex Fastening Solutions • Phone: 866-474-3739 • Fax: 716-875-0358www.aboveboardelectronics.com • www.sherex.com • E-mail:
[email protected]
UKO AND HUKO IMPERIAL THREAD SERIES - STAINLESS STEEL
UKO/ HUKO INCH
series
• 0 b_
..„Thread
(unit -
uko unified thread Part Number (304 Stainless Steel)
inches)
Grip Range (E)
Thread Size
Min.
Max.
L
D
K
Diameter-Inch (d)
Diameter-Metric (d)
Hole Size - Inch (b+.004)
Hole Size - Metric (b+0.1)
TU -SS1 032UKO3 0
10-32 UN F
.02 0
.11 8
.47 2
.29 5
.02 0
.27 6
7.0
.27 6
7.0
TU -SS2 520UKO3 0 TU -SS3 118UKO3 0
1/4-20 UNC 5/16-18 UNC
.02 0 .02 0
.11 8 .11 8
.57 1 .63 0
.37 4 .45 3
.02 0 .02 0
.35 4 .43 3
9.0 11.0
.35 4 .43 3
9.0 11.0
L
D
K
Diameter-Inch (d) (A/F)
Diameter-Metric ..1 (d) (A/F)
(b+.004) (A/F)
Hole Size - Metric (b+0.1) (A/F)
Grip Range (E)
0 D Hole • Size - Inch
• Round shank body.
0.3 Thread RSize
Min.
Max.
TU -SS1 032HUKO30
10-32 UN F
.02 0
.11 8
.47 2
.29 5
.02 0
.27 6
7.0
.27 6
7.0
TU -SS2 520HUKO30 TU -SS3 118HUKO30
1/4-20 UNC 5/16-18 UNC
.02 0 .02 0
.11 8 .11 8
.57 1 .63 0
.37 4 .45 3
.02 0 .02 0
.35 4 .43 3
9.0 11.0
.35 4 .43 3
9.0 11.0
Part Number (304 Stainless Steel)
Thread Size
L
D
K
Diameter-Inch (d)
Diameter-Metric (d)
Hole Size - Inch (b+.004)
Hole Size - Metric (b+0.1)
d
Part Number (304 Stainless Steel)
Grip Range (E) Min.
Max.
..4Th read
TU -SS1 032UKO3 0
10-32 UN F
.02 0
.11 8
.47 2
.29 5
.02 0
.27 6
7.0
.27 6
7.0
TU -SS2 520UKO3 0 TU -SS3 118UKO3 0
1/4-20 UNC 5/16-18 UNC
.02 0 .02 0
.11 8 .11 8
.57 1 .63 0
.37 4 .45 3
.02 0 .02 0
.35 4 .43 3
9.0 11.0
.35 4 .43 3
9.0 11.0
L
D
K
Diameter-Inch (d) (A/F)
Diameter-Metric (d) (A/F)
Hole Size - Inch (b+.004) (A/F)
Hole Size - Metric (b+0.1) (A/F)
huko unified thread
(unit -
inches)
Grip Range (E)
• The UKO inch series has a smaller flange head that gives a near flush installation.
Part Number (304 Stainless Steel)
Thread Size
Min.
Max.
TU -SS1 032HUKO30
10-32 UN F
.02 0
.11 8
.47 2
.29 5
.02 0
.27 6
7.0
.27 6
7.0
TU -SS2 520HUKO30 TU -SS3 118HUKO30
1/4-20 UNC 5/16-18 UNC
.02 0 .02 0
.11 8 .11 8
.57 1 .63 0
.37 4 .45 3
.02 0 .02 0
.35 4 .43 3
9.0 11.0
.35 4 .43 3
9.0 11.0
• Dimensions in inches.
• The HUKO inch series has a smaller flange head that gives a near flush installation. • Hexagonal shank body.
part numbering system
• Dimensions in inches. UKO/HUKO Specifications Material: Stainless Steel 304 Cu Stainless Steel 316 Cu
Part Number Example: SS1032HUKO30 TU Product Style Metric
SS 1032 Material Thread Size SS-304 Stainless Steel *316-316 Stainless Steel
HUK Product Type Small Flange Hexagonal Shank Inch Body
O O-Open End X-Closed End
30 Grip Range
Special finish or material available upon request
*316 Stainless Steel has extra corrosion resistance and can be used in the medical, chemical and food industries Grip Range can be affected by parent material and hole size. Sherex recommends trial installations to determine the proper grip range for the application. RoHS Compliant Trivalent Plating available upon request. Also available with imperial threads - minimum order quantity is 25,000 pieces if not in stock. Contact Sherex for test data.
INSTALLATION TOOLING UKO/HUKO Inch Series can be installed with our Hand Tools and Hydro-Pneumatic Tools. For additional tooling information see pages 38-42.
All Parts have been manufactured by:
DEJ01\113
TUBTARA®- A DEJOND PRODUCT Sherex rivet nuts are compatible with the following hardware: GRADE 2, GRADE 5, CLASS 8.8 and CLASS 9.8 Please contact Sherex when using other grade fasteners.
Sherex Fastening Solutions
•
Phone: 866-474-3739 716-875-0358 • Fax: Request Info
•
E-mail:
[email protected] •1-800-453-1692 www.aboveboardelectronics.com www.sherex.com
21
CLM/ CKM series
CLM & CKM LARGE & SMALL FLANGE KNURLED METRIC BODY SERIES GR
L
HOLE SIZE
y
14
clm metric thread
• The CLM series is the metric body version of the CAL series.
(unit -
Sherex Part Number Thread Size Metric - Steel
Grip Range (E) Min.
Max.
CLM2-470-3.0 CLM2-580-3.0 CLM2-610-3.0 CLM2-8125-3.0 CLM2-1015-3.5
0.25 0.25 0.50 0.50 0.50
3.00 3.00 3.00 3.00 3.50
M4X0.7 ISO M5X0.8 ISO M6X1.0 ISO M8X1.25 ISO M10X1.5 ISO
millimeters) L
HD
Nom. Min. Max. 11.5 13.0 16.0 17.5 22.0
8.62 9.62 12.62 15.62 18.12
9.38 10.38 13.38 16.38 18.88
GR
L
HT
D
±.13
Max.
0.75 1.00 1.50 1.50 2.25
5.95 6.95 8.95 10.95 12.95
IL
Hole Size
Ref. +0.10/-.000 7.10 7.90 9.40 11.00 14.50
6.00 7.00 9.00 11.00 13.00
HOLE SIZE
ID
-/THR E A D SIZE
FIT IL
ckm metric thread
• The CKM series is the metric body version of the CAK series.
Sherex Part Number Metric - Steel CKM2-470-3.0 CKM2-580-3.0 CKM2-610-3.0 CKM2-8125-3.0 CKM2-1015-3.5
Thread Size M4X0.7 ISO M5X0.8 ISO M6X1.0 ISO M8X1.25 ISO M10X1.5 ISO
(unit -
millimeters) L
Grip Range (E) Min.
Max.
0.25 0.25 0.50 0.50 0.50
3.00 3.00 3.00 3.00 3.50
HD
Nom. Min. Max. 11.3 12.7 15.3 17.3 20.4
6.70 7.20 7.70 8.20 9.70 10.20 11.62 12.38 13.62 14.38
HT
D
IL
Hole Size
±.13
Max.
Ref.
+0.10/-.000
0.46 0.46 0.50 0.63 0.80
5.95 7.10 6.95 7.90 8.95 9.40 10.95 11.00 12.95 14.50
6.00 7.00 9.00 11.00 13.00
part numbering system CLM/CKM Specifications Material: Steel 1008/1010 Aluminum 5056
Part Number Example: CLM2-610-3.0
CLM Product Style RoHS Compliant Finishes: Large Flange Zinc Plated-Yellow Trivalent Chromate Knurled Body per Sherex SFS-01-001, SC2 Metric Body Zinc Plated-Clear Trivalent Chromate per Sherex SFS-01-001 CKM Product Style Small Flange Knurled Body Metric Body
2 Material 2-Steel 3-Aluminum
610 Thread Size
3.0 Grip Range
(_) Empty-Open End B-Closed End T-Clear Trivalent
2 Material 2-Steel 3-Aluminum
610 Thread Size
3.0 Grip Range
(_) Empty-Open End B-Closed End T-Clear Trivalent
Special finish or material available upon request
Grip range can be affected by parent material and hole size. Sherex recommends trial installations to determine the proper grip range for the application. Contact Sherex for details. CLM & CKM style rivet nut specials available upon request. Contact Sherex for test data.
22
INSTALLATION TOOLING CLM/CKM Series can be installed with our Hand Tools, and Hydro-Pneumatic Tools. For additional tooling information see pages 38-42. Sherex rivet nuts are compatible with the following hardware: GRADE 2, GRADE 5, CLASS 8.8 and CLASS 9.8 Please contact Sherex when using other grade fasteners.
Sherex Fastening Solutions
•
Request Info 1-800-453-1692 • Fax: 716-875-0358 www.aboveboardelectronics.com • www.sherex.com • E-mail:
[email protected]
Phone: 866-474-3739
SHEREX CR/CRE SERIES
CR/CRE series
plating: cr and cre series
Corrosion Resistant - Long Life Plating Options CR SERIES • Proprietary Zinc Nickel Plating. • CR Series is certified to over 1,000 hrs of corrosion protection before red rust. • Available on all rivet nuts in silver (standard), black or yellow. CRE SERIES • Proprietary Zinc Plating. • More economical for lower corrosion resistance requirements. • CRE Series is certified to over 500 hrs of corrosion protection before red rust. • Available in silver (standard) or black. RoHS REQUIREMENTS • The CR & CRE Series are RoHS compliant. • Our plating process contains neither hexavalent nor trivalent chromate. • This saves cost as now there is no need to test for hexavalent presence.
Corrosion Protection 4000 Hours
3000 2000 1000 0
Zinc Plated Dicromate Steel
Anodized Aluminum
CRE Series
Material
CR Series
304 Stainless Steel
Additional information and Sherex white paper available at www.sherex.com Ordering & Inquires When inquiring about the CR and CRE Series finishes, simply replace the first 2 letters of the part number with CR or CRE. Example: CAL2-2520-165 becomes CREL2-2520-165 For non-standard finish, contact Sherex for ordering details. Sherex CR Black = CRB, Sherex CR Yellow = CRY, Sherex CRE Black = CREB
Request Info 1-800-453-1692 Sherex Fastening Solutions • Phone: 866-474-3739 • Fax: 716-875-0358 www.aboveboardelectronics.com • www.sherex.com • E-mail:
[email protected]
23
SHEREX LOCSERT® SHEREX LOCSERT®
Sherex Locsert® is a proprietary adhesive that is pre-applied under the head of the rivet nut. When installed, the adhesive bonds the rivet nut to the base material, greatly increasing the force required to spin the rivet nut. This is commonly referred to as “spin out.”
1 "V/F adhesive activates during installation bonding rivet nut to base material
product features and benefits
• • • • •
Base material must be a ferrous or non-ferrous metal. Base material should not be painted or powder coated (finish will reduce performance). Base material should be as clean as possible prior to rivet nut installation. Hole should be relatively free of burrs. Bonding begins immediately, but allow 2-3 hours for approximately 75% curing. Locsert® will be fully cured within 24 hours. • Locsert® performance will improve 20-30% when post bake associated with e-coat, powdercoat or paint finish is performed AFTER Locsert® installation. Base Material: 1018 steel, 70HRB, .063 thickness Part Number
Spin Out (in - lb)
As Locsert®
Set Time
CAL 2-252 0-16 5
42.9 0
90.0 8
3 hours
For contact Sherex Sherex Foradditional additionaltesting testingdata, data, please please contact
SHEREX SEAL 2 SEALING SYSTEM
SEAL 2 SEALING
system
Sherex Seal 2 has been designed for use in applications where it is necessary to seal fluid or air leakage from under the head. Seal 2 provides greater performance over conventional sealing materials such as PVC foam.
benefits
• • • • •
Resistant to automotive fluids. Can withstand temperatures up to 150° C. Has been pressure tested to 160 psi of backside pressure with no leakage. Seal 2 processed rivet nuts can be installed into any finished materials. Seal 2 can pass through a paint bake or other baking process for up to 30 minutes with no reduction in sealing capabilities. • Can be applied to a standard large flange rivet nut. -...0.^-
24 SHEREI FASITIVIIC SOLUTIO
Sherex Fastening Solutions
•
Request Info 1-800-453-1692 • Fax: 716-875-0358www.aboveboardelectronics.com • www.sherex.com • E-mail:
[email protected]
Phone: 866-474-3739
RIV-FLOAT® RIV-FLOAT®
STANDARD RIVET NUT INSTALLED
CROSS SECTION OF RIV-FLOAT® INSTALLED
features and benefits
• Accounts for tolerance stack up in joint design and misalignment during service of the joint. • Floating nut aligns to drive angle of screw virtually eliminating cross threading and spin out. • Allows for installation in post painted or powder coat applications where riveted nut plates or cage nuts are typically used • RoHS compliant Zinc electroplate to 8µm with trivalentchromate - 96/240 hrs (WR/RR) • Designed with higher thread strength than regular rivet nuts • Mechanically locked RIV-FLOAT® is available with prevailing torque feature to IFI spec 100/107 GR HT
• The RIV-FLOAT® series provides easy, accurate, and fast attachment of components in off-center applications.
CENTERING NOSEPIECE
IL
L
HD
D 1
INSTALLED
UNINSTALLED
rfk inch thread small flange series Part Number Inch (Steel)
Thread Size
Radial Deflection
Part Number Number Part RFK2-0632-130 Inch (Steel) (Steel) Inch RFK2-0832-130
6-32 UNC Thread Size Thread Size 8-32 UNC
Radial Radial 0.020 Deflection Deflection 0.020
RFK2-1032-150 RFK2-0632-130 RFK2-0832-130 RFK2-2520-150 Part Number RFK2-0832-130 RFK2-1032-150 Inch (Steel) RFK2-1032-150 RFK2-2520-150
10-32 UNF 6-32 UNC 8-32 UNC 1/4-20 UNC 8-32 UNC Thread Size 10-32 UNF 10-32 UNF 1/4-20 UNC
0.015 0.020 0.020 0.030 Radial 0.020 0.015 Deflection 0.015 0.030
Grip Range Min. Max. Grip Range Range Grip 0.027 .130 Min. Max. Min. Max. 0.027 .130
L ± .0215 L L .7195 ± .0215 .0215 ± .7195
(unit -
HD
HT
D
IL
± .010 HD HD .455 ± .010 .010 ± .455
± .002 HT HT .022 ± .002 .002 ± .022
Max. D D .390 Max. Max. .390
Ref. IL IL .522 Ref. Ref. .522
0.027 .150 .7195 .455 .022 0.027 .130 .7195 .455 .022 Grip Range L HD HT 0.027 .130 .7195 .455 .022 0.027 .150 .8190 .595 .022 0.027 .130 .7195 .455 .022 0.027 .150 .7195 .455 .022 Min. Max. ± .7195 .0215 ± .455 .010 ± .022 .002 0.027 .150 0.027 .150 .8190 .595 .022 rfk metric thread small flange series unit Grip Range L HD HT RFK2-2520-150 1/4-20 UNC 0.030 0.027 .150 .8190 .595 .022 Part Number Radial RFK2-0832-130 8-32 UNC 0.020 0.027 .130 .7195 .455 .022 Thread Size Metric (Steel) Deflection Grip Range L HD HT Min. Max. ± .55 ±.455 .25 ±.022 .05 RFK2-1032-150 10-32 UNF 0.015 0.027 .150 .7195 Part Number Radial Grip Range L HD HT Thread Size RFK2-2520-150 1/4-20 UNC 0.030 0.027 .150 .8190 .595 .022 Part Number Radial Metric (Steel) Deflection Min. Max. ± .55 ± .25 ±0.55 .05 RFK2-470-3.3 M4x0.7 Size ISO 0.51 0.7 3.3 18.28 11.56 Thread Metric (Steel) Deflection Min. Max. ± .55 ± .25 ± .05 RFK2-580-3.8 M5X0.8 ISO 0.38 0.7 3.8 18.28 11.56 0.55 Grip L HD HT RFK2-470-3.3 M4x0.7 ISO 0.51 0.7 Range 3.3 18.28 11.56 0.55 RFK2-610-3.8 M6x1.0 ISO 0.76 0.7 3.8 20.80 15.11 0.55 Part Number Radial RFK2-470-3.3 M4x0.7 Size ISO 0.51 0.7 3.3 18.28 11.56 0.55 Thread RFK2-580-3.8 M5X0.8 ISO 0.38 0.7 3.8 18.28 11.56 0.55 Metric (Steel) Deflection Min. Max. ± .55 ± .25 ± .05 RFK2-580-3.8 M5X0.8 ISO ISO 0.38 0.7 3.8 18.28 11.56 0.55 RFK2-610-3.8 M6x1.0 0.76 0.7 3.8 20.80 15.11 0.55 RFK2-610-3.8 M6x1.0 ISO 0.76 0.7 3.8 20.80 15.11 0.55 RFK2-470-3.3 M4x0.7 ISO 0.51 0.7 3.3 18.28 11.56 0.55 Grip Range L HD HT RFK2-580-3.8 M5X0.8 ISO 0.38 0.7 3.8 18.28 11.56unit 0.55 Radial Part Number rfl inch thread large flange series Thread Size RFK2-610-3.8 M6x1.0 ISO 0.76 0.7 Range 3.8 20.80 0.55 Grip L HD HT Deflection Inch (Steel) Min. Max. ± .0215 ± 15.11 .010 ± .003 Radial Part Number L HD HT Grip Range Thread Size Radial Part Deflection InchNumber (Steel) Min. Max. ± .7195 .0215 ± .500 .010 ± .030 .003 Thread Size RFL2-0632-130 6-32 UNC 0.020 .027 .130 Deflection Inch (Steel) Min. Max. ± .0215 ± .010 ± .003 RFL2-0832-130 8-32 UNC 0.020 .027 .130 .7195 .500 .030 L HD HT Grip Range RFL2-0832-130 8-32 UNC 0.020 .027 .130 .7195 .500 .030 Radial Part Number RFL2-1032-150 10-32 UNF 0.015 .027 .150 .7195 .500 .030 RFL2-0632-130 6-32 UNC 0.020 .130 Thread Size RFL2-1032-150 10-32 UNF 0.015 .027 .150 .7195 .500 .030 Deflection Inch (Steel) Min. Max. ± .0215 ± .010 ± .003 RFL2-2520-150 1/4-20 UNC 0.030 .027 .150 .8190 .685 .035 RFL2-0832-130 8-32 UNC 0.020 .130 .7195 .500 .030 RFL2-2520-150 1/4-20 UNC 0.030 .027 .150 .8190 .685 .035 RFL2-1032-150 10-32 UNF 0.015 .027 .150 .7195 .500 .030 RFL2-0832-130 8-32 UNC 0.020 .027 .130 .7195 .500 .030
(
Hole Size +.006/-.000 Hole Size Size Hole .391 +.006/-.000 +.006/-.000 .391
.390 .522 .391 .390 .522 .391 D IL Hole Size .390 .522 .391 .530 .630 .531 .390 .522 .391 .390 .522 .391 Max. Ref. +.006/-.000 .390 .522 .391 .530 .630 .531 millimeters D IL Hole Size .530 .630 .531 .390 .522 .391 D IL Hole Size Max. Ref. +.15/-.000 .390 .522 .391 D IL Hole Size .530 .630 .531 Max. Ref. +.15/-.000 9.91 13.25 10.00 Max. Ref. +.15/-.000 9.91 13.25 10.00 D IL Hole Size 9.91 13.25 10.00 13.46 16.00 13.50 9.91 13.25 10.00 9.91 13.25 10.00 Max. Ref. +.15/-.000 9.91 13.25 10.00 13.46 16.00 13.50 I 13.46 16.00 13.50 9.91 13.25 10.00 D IL Hole Size 9.91 13.25 10.00 inches
-
-
(
• The RIV-FLOAT® series should be installed with the FLEX-5 Hydro Pneumatic Tool with a RIV-FLOAT®Anvil.
inches)
)
= )
'77771
Grip L HD RFL2-2520-150 1/4-20 UNC 0.030 .027 Range .150 .8190 .685 RFL2-1032-150 10-32 UNF 0.015 .027 .150 .7195 .500 Radial Part Number Grip Range L HD Thread Size Radial Part Number RFL2-2520-150 1/4-20 UNC 0.030 .027 .150 .8190 Deflection Metric (Steel) Thread Size Min. Max. ± .55 ±.685 .25 rfl thread large flange series Deflection Metricmetric (Steel) Min. Max. ± .55 ±HD .25 Grip Range L Radial Part Number Thread RFL2-470-3.3 M4x0.7 Size ISO 0.51 0.7 Range 3.3 18.28 12.70 Grip L HD Deflection Metric (Steel) Min. Max. ± .55 ± .25 RFL2-470-3.3 M4x0.7 ISO 0.51 0.7 3.3 18.28 12.70 Radial Part Number RFL2-580-3.8 M5x0.8 Size ISO 0.38 0.7 3.8 18.28 12.70 Thread RFL2-580-3.8 M5x0.8 ISO 0.38 0.7 3.8 18.28 12.70 Deflection Metric (Steel) Min. Max. ± .55 ± .25 RFL2-610-3.8 M6x1.0 0.76 0.7 3.8 20.80 17.40 RFL2-470-3.3 M4x0.7 ISO 0.51 3.3 18.28 12.70 RFL2-610-3.8 M6x1.0 ISO 0.76 0.7 3.8 20.80 17.40 RFL2-580-3.8 M5x0.8 0.38 0.7 3.8 18.28 12.70 RFL2-470-3.3 M4x0.7 ISO ISO 0.51 0.7 3.3 18.28 12.70 RFL2-610-3.8 RFL2-580-3.8
M6x1.0 ISO ISO M5x0.8
0.76 0.38
0.7 0.7
3.8 3.8
20.80 18.28
17.40 12.70
HT .035 .030 HT ±.035 .08 unit ± HT .08
(
-
13.46 D Max. D Max. .390 Max. .390 D .390 .390 .390 Max. .530 .390 .530 .390 .390
16.00 IL Ref. IL Ref. .522 Ref. .522 IL .522 .522 .522 Ref. .630 .522 .630 .522 .522
13.50 Hole Size +.006/-.000 Hole Size +.006/-.000 .391 +.006/-.000 .391 Hole Size .391 .391 .391 +.006/-.000 .531 .391 .531 .391 .391
D IL Hole Size .530 .630 .531 .390 .522 .391 D IL Hole Size .530 .630 .531 Max. Ref. +.15/-.000 millimeters Max. Ref. +.15/-.000 D IL Hole Size
)
0.76 HT ±0.76 .08 0.76 ±0.76 .08 0.89 0.76 0.89 0.76 0.76
9.91 D Max. 9.91 9.91 9.91 Max. 13.46 9.91 13.46 9.91 9.91
13.25 IL Ref. 13.25 13.25 13.25 Ref. 16.00 13.25 16.00 13.25 13.25
0.89 0.76
13.46 9.91
16.00 13.25
10.00 Hole Size +.15/-.000 10.00 10.00 10.00 +.15/-.000 13.50 10.00 13.50 10.00 10.00
l
ge
'E
ti
El
13.50 10.00
RFL2-610-3.8
M6x1.0 ISO 0.76 0.7 3.8 20.80 17.40 0.89 13.46 16.00 Suggested 13.50 Material Suggested Thread Failure Mode Failure Mode Assembly Torque Material Thickness Pull Out ® is Failure Out “7,713,011” Thread Mode Failure Mode Assembly Torque RIV-FLOAT covered under US Torque Patent No. Size (Pull Out) (Torque Out) Grade 5 Thickness Pull Out Torque Out Suggested (Steel) Request Info Size (Pull Out) (Torque Out) 1-800-453-1692 Grade 5 Material Class Torque 8.8 (Steel) Thread Failure Mode Failure Mode Assembly Sherex Fastening Solutions www.sherex.com • E-mail:
[email protected] • Phone: 866-474-3739 • Fax: 716-875-0358 Suggested Class 8.8 Thickness Pull Out Torque• Out Material www.aboveboardelectronics.com Size (Pull Out) (Torque Out) Grade 5 Thread Failure Mode Failure Mode Assembly Torque # 8-32 UNC .130" 2205 lbf Bolt Breaks 71 in-lb Bolt Breaks 22.0 in-lb (Steel) Thickness Pull Out Torque Out
25
Part Number
Radial
Thread Size
RIV-FLOAT® Metric (Steel)
RIV-FLOAT®
series
Grip Range
L
HD
HT
D
IL
Deflection
Min.
Max.
± .55
± .25
± .08
Max.
Ref.
Hole Size +.15/-.000
RFL2-470-3.3
M4x0.7 ISO
0.51
0.7
3.3
18.28
12.70
0.76
9.91
13.25
10.00
RFL2-580-3.8
M5x0.8 ISO
0.38
0.7
3.8
18.28
12.70
0.76
9.91
13.25
10.00
RFL2-610-3.8
M6x1.0 ISO
0.76
0.7
3.8
20.80
17.40
0.89
13.46
16.00
13.50
test data Suggested
Material
Thread
Thickness
Size
FLOAT®®
Pull Out
(Steel)
Failure Mode (Pull Out)
Failure Mode
Torque Out
Assembly Torque
(Torque Out)
RIV FLOAT Rivet Nut Hand Tool Installation ®lbf # 8-32 UNC .130" 2205 Breaks 71 in-lb Bolt Breaks Kit Pricing RIV FLOAT Rivet Bolt Nut Hand Tool Installation # 10-32 UNF .150" 3530 lbf Bolt Breaks 128 in-lb Bolt Breaks Kit Pricing
Grade 5 Class 8.8 22.0 in-lb 36.0 in-lb
1/4-20 UNC
.150"
5510 lbf
Bolt Breaks
265 in-lb
Bolt Breaks
75.0 in-lb
M4x0.7 ISO
3.3 mm
1000 kgf
Bolt Breaks
9 N•m
Bolt Breaks
2.5 N•m
M5x0.8 ISO
3.8 mm
1900 kgf
Bolt Breaks
21 N•m
Bolt Breaks
5.0 N•m
M6x1.0 ISO
3.8 mm
2500 kgf
Bolt Breaks
30 N•m
Bolt Breaks
8.6 N•m
-
Part Part Number: Number: Tools Tools Sizes: Sizes: Rivet Rivet Nuts: Nuts:
30 30 30 30 30 30 20 20
® 6-32 / / 8-32 8-32 10-32 / / ¼-20 ¼-20 6-32 10-32 riv float rivet nut hand tool kits Inch Metric Kit Inch Kit Kit Metric Kit Mini Inch Inch Kit Kit Mini Inch Inch Kit Kit Mini Mini RNHT RF INCH KIT RNHT RF METRIC KIT RNHT 6-32/8-32 RF MINI KIT RNHT 10-32/2520 MINI 6-32 / RF 8-32 RNHT RF INCH KIT RNHT RF METRIC KIT RNHT 6-32/8-32 RF MINI RNHT 10-32/2520 RF MINI KIT KIT Inch Kit Metric Kit KIT 6-32 to ¼-20 M4 to M6 ¼-28 10-32 and ¼-20 Mini Inch Kit 6-32 to ¼-20 M4 to M6 ¼-28 10-32 and ¼-20 pieces of of RFL2-0632-130 RFL2-0632-130 30 pieces piecesRNHT of RFL2-470-3.3 RFL2-470-3.3 20 pieces pieces of RFL2-0632-130 RFL2-0632-130 20RNHT pieces of RFL2-1032-150 RFL2-1032-150 Part Number:30 RF INCH KIT 20 RNHT RF METRIC KIT 6-32/8-32 RF MINI KIT pieces of of 20 pieces of pieces of of RFL2-0832-130 RFL2-0832-130 30 pieces pieces of of6-32 RFL2-580-3.8 20 pieces pieces of of RFL2-0832-130 RFL2-0832-130 10 pieces pieces of of RFL2-2520-150 RFL2-2520-150 Tools Sizes: 30 to ¼-20 M4 to M6 ¼-28 pieces RFL2-580-3.8 20 10 pieces 20 of 30 pieces of RFL2-0632-130 30 pieces of RFL2-470-3.3 20 pieces of RFL2-0632-130 pieces of of RFL2-1032-150 RFL2-1032-150 20 pieces pieces of RFL2-610-3.8 RFL2-610-3.8 pieces of RFL2-2520-150 30 pieces of RFL2-0832-130 30 pieces of RFL2-580-3.8 20 pieces of RFL2-0832-130 pieces of RFL2-2520-150 Rivet Nuts: Each tool comes comes with an an extra extra mandrel mandrel 30 pieces of RFL2-1032-150 20 pieces of RFL2-610-3.8 Each tool with 20 pieces of RFL2-2520-150
10-32 / ¼-20 Mini Inch Kit RNHT 10-32/2520 RF MINI KIT 10-32 and ¼-20 20 pieces of RFL2-1032-150 10 pieces of RFL2-2520-150
Each tool comes with an extra mandrel MECHANICALLY MECHANICALLY LOCKED LOCKED PARTS PARTS
Mechanically Mechanically Mechanically Locked Locked Mechanically Locked Locked Inch Kit Kit Metric MECHANICALLY LOCKED PARTS Inch Metric Kit Kit ® ® Part Number: Number: RNHT RF RF ML ML INCH INCH KIT KIT RNHT RF RFMechanically ML METRIC METRIC KIT KIT Locked Mechanically Locked Part RNHT RNHT ML Tools Sizes: Sizes: ¼-28 ¼-28 Inch Kit Metric Kit Tools ¼-28 ¼-28 20 pieces of SH-22-0632 20 pieces of SH-22-470 Part Number: RNHT RF ML INCH KIT RNHT RF ML METRIC KIT 20 pieces of SH-22-0632 20 pieces of SH-22-470 Rivet Nuts: 20 pieces of SH-22-0832 20 pieces of SH-22-580 Tools Sizes: ¼-28 ¼-28 Rivet Nuts: 20 pieces of SH-22-0832 20 pieces of SH-22-580 20 pieces pieces of of SH-22-1032 SH-22-1032 20 pieces of SH-22-0632 20 pieces of SH-22-470 20 Each tool tool comes comes with withRivet an extra extra mandrel20 pieces of SH-22-0832 Nuts: 20 pieces of SH-22-580 Each an mandrel 20 pieces of SH-22-1032
RIV RIV FLOAT FLOAT Rivet Rivet Nut Nut Hand Hand Tool Tool Installation Installation Bag Pricing Bag Pricing
Each tool comes with an extra mandrel Contact Contact Sherex Sherex for for availability availability and and lead lead times times Private label label available available upon upon request request Private Contact Sherex for availability and lead times Private label available upon request
riv-float® rivet nut hand tool bag Part Number: Part Number: Tools Sizes: Tools Sizes: Rivet Nuts: Rivet Nuts:
6-32 BAG 6-32 BAG RNHT-0632RF BAG RNHT-0632RF BAG ¼-28 ¼-28 15 pieces of RFL2-0632-130 15 pieces of RFL2-0632-130
Part Number: Part Number: Tools Sizes: Tools Sizes: Rivet Nuts: Rivet Nuts:
M4 BAG M4 BAG RNHT-M4RF BAG RNHT-M4RF BAG ¼-28 ¼-28 15 15 pieces pieces of of RFL2-470-3.3 RFL2-470-3.3
8-32 BAG 8-32 BAG RNHT-0832RF BAG RNHT-0832RF BAG ¼-28 ¼-28 15 pieces of RFL2-0832-130 15 pieces of RFL2-0832-130
10-32 BAG 10-32 BAG RNHT-1032RF BAG RNHT-1032RF BAG 10-32 10-32 15 pieces of RFL2-1032-150 15 pieces of RFL2-1032-150
M5 BAG M5 BAG RNHT-M5RF BAG RNHT-M5RF BAG M5 M5 15 15 pieces pieces of of RFL2-580-3.8 RFL2-580-3.8
M6 BAG M6 BAG RNHT-M6RF BAG RNHT-M6RF BAG M6 M6 10 10 pieces pieces of of RFL2-610-3.8 RFL2-610-3.8
Each Each tool tool comes comes with with an an extra extra mandrel mandrel
Each Each tool tool comes comes with with an an extra extra mandrel mandrel
¼-20 BAG ¼-20 BAG RNHT-2520RF BAG RNHT-2520RF BAG ¼-20 ¼-20 10 pieces of RFL2-2520-150 10 pieces of RFL2-2520-150
Sherex Sherex Fastening Fastening Solutions Solutions ~ ~ 400 400 Riverwalk Riverwalk Pkwy, Pkwy, Suite Suite 600 600 ~ ~ Tonawanda, Tonawanda, NY NY 14150 14150 8664 74 74 3739 3739 ~ ~ www.sherex.com www.sherex.com 8664 MECHANICALLY LOCKED PARTS Pricing effective effective March, 2009 2009 MECHANICALLY PARTS Pricing March, Sherex Fastening SolutionsLOCKED ~ 400 Riverwalk Pkwy, Suite 600 ~ Tonawanda, NY 14150 Mechanically Locked Mechanically Locked Mechanically Locked Mechanically Locked Mechanically Locked Mechanically Locked 8664 74 3739 ~ www.sherex.com 6-32 BAG 8-32 BAG 10-32 BAG Pricing effective March, 2009 10-32 BAG 6-32 BAG 8-32 BAG Part Number: RNHT-0632RF ML BAG RNHT-0832RF ML BAG RNHT-1032RF ML BAG Part Number: RNHT-0632RF ML BAG RNHT-0832RF ML BAG RNHT-1032RF ML BAG Tools Sizes: ¼-28 ¼-28 ¼-28 Tools Sizes: ¼-28 ¼-28 ¼-28 Rivet Nuts: 15 pieces of SH-22-0632 15 pieces of SH-22-0832 15 pieces of SH-22-1032 Rivet Nuts: 15 pieces of SH-22-0632 15 pieces of SH-22-0832 15 pieces of SH-22-1032
Each Each tool tool comes comes with with an an extra extra mandrel mandrel
MECHANICALLY MECHANICALLY LOCKED LOCKED PARTS PARTS Part Number: Part Number: Tools Sizes: Tools Sizes: Rivet Nuts: Rivet Nuts:
Mechanically Locked Mechanically Locked M4 BAG M4 BAG RNHT-M4RF ML BAG RNHT-M4RF ML BAG ¼-28 ¼-28 15 pieces of SH-22-470 15 pieces of SH-22-470
Mechanically Locked Mechanically Locked M5 BAG M5 BAG RNHT-M5RF ML BAG RNHT-M5RF ML BAG ¼-28 ¼-28 15 pieces of SH-22-580 15 pieces of SH-22-580
R.51. GAG
Each Each tool tool comes comes with with an an extra extra mandrel mandrel
Contact Sherex for Riv-Float® Short kits and bags Contact Sherex availability and Contact Sherex for for availability and lead lead times timesand Contact Sherex for availability Private Private label label available available upon upon request request
lead times Private label available upon request RIV-FLOAT® is covered under US Patent No. “7,713,011”
26
Sherex Fastening Solutions
•
Request Info Phone: 866-474-3739 716-875-0358 • Fax:
E-mail:
[email protected] • www.sherex.com •1-800-453-1692 www.aboveboardelectronics.com
Features and Benefits of RIV-FLOAT - SHORT
® - SHORT • ACCOUNTS FOR TOLERANCE STACK UPof IN JRIV-FLOAT OINT DESIGN AND Features and Benefits ® • MISALIGNMENT ACCOUNTS FOR DURING TOLERANCE STACK UP IN J OINT DESIGN AND SERVICE OF THE J OINT RIV-FLOAT -SHORT ® - SHORT • ACCOUNTS FOR DURING TOLERANCE STACK INJJOINT OINT DESIGN RIV-FLOAT Installed CROSSAND SECTION OF RIV-FLOAT® - SHORT Ins MISALIGNMENT SERVICE OFUP THE •• ACCOUNTS FOR TOLERANCE STACK UP IN J OINT DESIGN AND RIV-FLOAT® NEW LOW-PROFILE DESIGN PROVIDES GREATER MISALIGNMENT DURING SERVICE OF THE J OINT BACKSIDE CLEARANCE SHORT • MISALIGNMENT NEW LOW-PROFILE DESIGN PROVIDES GREATER DURING SERVICE OF THE J OINT BACKSIDE CLEARANCE ALLOWS INSTALLATION POST FINISH IN APPLICATIONS WHERE WELD NUTS • NEW LOW-PROFILE DESIGN PROVIDES GREATER BACKSIDE CLEARANCE series ALLOWS INSTALLATION POST FINISH APPLICATIONS WHERE WELD NUTS • NEW LOW-PROFILE PROVIDES GREATER BACKSIDE CLEARANCE OR CAGE NUTS AREDESIGN TYPCIALLY USEDIN • ALLOWS POST FINISH OR CAGEINSTALLATION NUTS ARE TYPCIALLY USEDIN APPLICATIONS WHERE WELD NUTS ® IN •• ALLOWS INSTALLATION POST FINISH APPLICATIONS WHERE NUTS - SHORT AVAILABLE WITHWELD PREVAILING MECHANICALLY LOCKED RIV-FLOAT OR CAGE NUTS ARE TYPCIALLY USED ® - SHORT AVAILABLE WITH PREVAILING • OR MECHANICALLY LOCKED RIV-FLOAT CAGE NUTS ARE TYPCIALLY USED TORQUE FEATURE TO IFI SPEC 100/ 107 ® - SHORT AVAILABLE WITH PREVAILING • MECHANICALLY LOCKED RIV-FLOAT TORQUE FEATURE TO IFI SPEC 100/ 107 ® - SHORT AVAILABLE WITH PREVAILING •• MECHANICALLY LOCKED RIV-FLOAT 0.020” RADIAL FLOAT TORQUE FEATURE TO IFI SPEC 100/ 107 • 0.020” RADIAL FLOAT TORQUE FEATURE TO IFI SPEC 100/ 107 Standard Rivet Nut Installed Cross Section of a Standard SHORT Installed CROSS --SHORT SHORT Installed Installed CROSSSECTION SECTIONOFOFRIV-FLOAT ROHS COMPLIANT •RIV-FLOAT 0.020” RADIAL FLOAT Rivet Nut Installed ROHS COMPLIANT • 0.020” RADIAL FLOAT features and benefits • ROHS COMPLIANT Sherex rivet nuts are compatible with the following hardware: • ROHS COMPLIANT • Accounts for tolerance stack up in joint design and misalignment during service of the2,joint. GRADE GRADE 5, CLASS 8.8 and CLASS 9.8 ®®
ivet Nut Installed
• • • • •
• The RIV-FLOAT series Please contact Sherex when using other grade fasteners. New Low-Profile design provides greater backside clearance. provides easy, accurate, Allows for installation post finish in applications where riveted nut plates or cage nuts are typically used. and fast attachment ® - SHORT is installed with Flex-5 Hydro-Pneumatic tool RIV-FLOAT of components in Mechanically locked RIV-FLOAT®-Short available with prevailing torque feature to IFI SPEC 100/107. GRIP RANGE ® - SHORT Anvil off-center applications. with RIV-FLOAT GRIP RANGE 0.020” Radial Float. Cross Section of a Standard GRIP RANGE RoHS Compliant. Rivet Nut Installed Sherex Fastening Solutions • 400 Riverwalk Pkwy, Suite 600 • Tonawanda, NY 14150 • Phone: 866-474-3739 ®
GRIP RANGE
Sherex rivet nuts are compatible with the following hardware: GRADE 2, GRADE 5, CLASS 8.8 and CLASS 9.8 Please contact Sherex when using other grade fasteners.
CENTERING NOSEPIECE
GRIP RANGE p.m* Welt
OAT - SHORT is installed with Flex-5 Hydro-Pneumatic tool with RIV-FLOAT® - SHORT Anvil ®
Uninstalled Uninstalled Installed Uninstalled small flange series (unit RFSKUninstalled SERIES - SMALL FLANGE
Installed Installed Installed Installed inches )
verwalk Pkwy, Suite 600 • Tonawanda, NY 14150 • Phone: 866-474-3739 • www.sherex.com
Unlnstalled
rfk inch thread SHEREX SHEREX Part Number
Thread Size
Part Number Inch - Steel SHEREX
Thread Size
Inch - Steel Part Number SHEREX RFSK2-0832-100 Inch Steel Part Number RFSK2-0832-100 RFSK2-1024-100 Inch - Steel RFSK2-1024-100 RFSK2-1032-100 RFSK2-0832-100 RFSK2-1032-100 RFSK2-1024-100 RFSK2-0832-100
Thread Size 8-32 UNC Thread Size 8-32 UNC 10-24 UNC
RFSK SERIES - SMALL FLANGE L HD HT Grip Range - SMALL RFSK SERIES FLANGE L HD HT Grip Range - SMALL RFSK SERIES FLANGE Radial Float
Radial Float Radial Float Radial 0.020 Float 0.020
10-24 UNC 10-32 UNF 8-32 UNC 10-32 UNF 10-24 UNC 8-32 UNC
M in. Range M ax . Grip M in. Range M ax . Grip .020 .100 M in. M ax . .020 .100 M in. M.100 ax . .020 .020 .100 .020 .100 .020 .100
±L .01 ± L.01 .394 ± .01 .394 ±.394 .01 .394 .394 .394
± HD .012
± HT .003
± HD .012 .480 ± .012 .480 ± .480 .012 .480 .480 .480
± HT .003 .025 ± .003 .025 ± .025 .003 .025 .025 .025
D
IL
D
IL
Hole Size Hole Size
MD ax . MD ax . .431 M ax . .431 M.431 ax . .431 .431 .431
RIL ef. RIL ef. .246 R ef. .246 R.246 ef. .246 .246 .246
+.006/ -.000 Hole Size +.006/ -.000 Hole Size .433 +.006/ -.000 .433 +.006/ -.000 .433 .433 .433 .433
M
0.020 0.020 0.020 rfk metric thread small flange series unit millimeters RFSK2-1032-100 10-32 UNC UNF 0.020 .020 .100 .394 .480 .025 .431 .246 .433 RFSK2-1024-100 10-24 SHEREX L HD HT D IL Hole Size Grip Range Radial RFSK2-1032-100 10-32 UNF 0.020 .020 .100 .394 .480 .025 .431 .246 .433 SHEREX Part Number Thread Size L HD HT D IL Hole Size Grip Range Radial Float Part Number Thread Size Metric - Steel SHEREX M in. Range M ax . ±L .25 ±HD .30 ±HT .07 MD ax . RIL ef. +.15/Size -.00 Hole Grip Float Radial Metric - Steel Part Number Thread Size M in. Range M ax . ± L.25 ±HD .30 ±HT .07 MD ax . RIL ef. +.15/Size -.00 SHEREX Hole Grip Float Radial RFSK2-470-2.5 M4x0.7 ISO 0.50 0.50 2.50 10.00 12.20 .63 10.95 6.25 11.00 Metric - Steel Part Number Thread Size M in. M ax . ± .25 ± .30 ± .07 M ax . R ef. +.15/ -.00 Float RFSK2-470-2.5 M4x0.7 ISO 0.50 0.50 2.50 10.00 12.20 .63 10.95 6.25 11.00 RFSK2-580-2.5 M5X0.8 Metric - Steel M in. M ax . ± .25 ± .30 ± .07 M ax . R ef. +.15/ -.00 RFSK2-580-2.5 M5X0.8 ISO 0.50 0.50 2.50 10.00 12.20 .63 10.95 6.25 11.00 RFSK2-470-2.5 M4x0.7 ISO 0.50 2.50 10.00 12.20 .63 10.95 6.25 11.00 RFSK2-580-2.5 RFSK2-470-2.5
M5X0.8 M4x0.7 ISO
RFSK2-580-2.5
M5X0.8 ISO
rflSHEREX inch thread SHEREX Part Number
Thread Size
Part Number Inch - Steel SHEREX
Thread Size
Inch - Steel Part Number SHEREX RFSL2-0832-100 InchNumber - Steel Part RFSL2-0832-100 RFSL2-1024-100 Inch - Steel RFSL2-1024-100 RFSL2-1032-100 RFSL2-0832-100
Thread Size 8-32 UNC Thread Size 8-32 UNC 10-24 UNC
M5x0.8 M4x0.7 ISO
-
)
0.50 0.50 2.50 10.00 12.20 .63 10.95 6.25 11.00 RFSL SERIES - LARGE FLANGE 0.50 0.50 2.50 - LARGE 10.00 12.20 .63 10.95 6.25 11.00 RFSL SERIES FLANGE L HD (unit HT D IL Hole Size Grip Range - LARGE large flange series inches RFSL SERIES FLANGE ) Radial L HD HT D IL Hole Size Grip Range - LARGE RFSL SERIES FLANGE Radial Float
Float Radial Float Radial 0.020 Float 0.020
Grip M in. Range M ax .
±L .01
± HD .015
± HT .003
MD ax .
RIL ef.
Hole Size +.006/ -.000
M in. Range M ax . Grip .020 .100 M in. M ax . .020 .100 M in. M ax . .020 .100 .020 .100
± L.01 .406 ± .01 .406 ± .01 .406 .406
± HD .015 .555 ± .015 .555 ± .015 .555 .555
± HT .003 .033 ± .003 .033 ± .003 .033 .033
MD ax . .431 M ax . .431 M ax . .431 .431
RIL ef. .246 R ef. .246 R ef. .246 .246
+.006/ -.000 Hole Size .433 +.006/ -.000 .433 +.006/ -.000 .433 .433
10-24 UNC 10-32 UNF 8-32 UNC 0.020 RFSL2-1032-100 10-32 UNF 0.020 .020 .100 .406 .555 RFSL2-1024-100 10-24 UNC RFSL2-0832-100 8-32 UNC 0.020 .020 .100 .406 .555 RFSL2-1032-100 10-32 UNC UNF RFSL2-1024-100 10-24 0.020 .020 .100 .406 .555 SHEREX L HD Grip Range Radial RFSL2-1032-100 10-32 UNF 0.020 .020 .100 .406 .555 SHEREX Part Number Thread Size L series HD Grip Range rfl metric thread small flange Radial Float Part Number Thread Size Metric - Steel SHEREX Grip M in. Range M ax . ±L .30 ±HD .38 Float Radial Metric - Steel Part Number Thread Size SHEREX M in. Range M ax . ± L.30 ±HD .38 Grip Float Radial RFSL2-470-2.5 M4x0.7 ISO 0.50 0.50 2.50 10.30 14.10 Metric - Steel Part Number Thread Size M in. M ax . ± .30 ± .38 Float RFSL2-470-2.5 M4x0.7 ISO 0.50 0.50 2.50 10.30 14.10 RFSL2-580-2.5 M5x0.8 Metric - Steel M in. M ax . ± .30 ± .38 RFSL2-580-2.5 M5x0.8 ISO 0.50 0.50 2.50 10.30 14.10 RFSL2-470-2.5 M4x0.7 0.50 0.50 2.50 10.30 14.10 RFSL2-580-2.5 RFSL2-470-2.5
(
0.50
0.50
2.50
10.30
14.10
.033 .431 .246 .433 .033 .431 .246 .433 .033 .431 .246 .433 HT D IL Hole Size .033 .431 .246 .433 HT D millimeters IL Hole Size unit
-
(
±HT .08
MD ax .
RIL ef.
Hole +.15/Size -.00
±HT .08 .85 ± .08 .85 ± .08 .85 .85
MD ax . 10.95 M ax . 10.95 M ax . 10.95 10.95
RIL ef. 6.25 R ef. 6.25 R ef. 6.25 6.25
+.15/Size -.00 Hole 11.00 +.15/ -.00 11.00 +.15/ -.00 11.00 11.00
.85
10.95
6.25
11.00
)
SHEREX AER SHEREX AER PART AER NUM SHEREX PART AER NUM SHEREX PART NUM RFSK2-0832-1 PART NUM
RFSK2-0832-1 RFSK2-0832-1 RFSK2-1032-1 RFSK2-0832-1 RFSK2-1032-1 RFSK2-1032-1 RFSK2-1032-1
Prints and Tech Prints and Tech are Prints available ww andatTech are Prints available ww andatTech are available at ww are available at ww Patent Pe Patent Pe Patent Pen Patent Pen
Sherex Fastening Solutions • 400 Riverwalk Pkwy, Suite 600 • Tonawanda,11.00 NY 14150 • Phone: 866-474-3739 Sherex Fastening Solutions •*RIV-FLOAT 400 Riverwalk Pkwy, Suite 600 • Tonawanda, NY 14150 • Phone: 866-474-3739 ® -Short is patent pending* Sherex Fastening Solutions •Request 400 Riverwalk Pkwy, Suite 600 • Tonawanda, NY Info 27 1-800-453-1692 14150 • Phone: 866-474-3739 Sherex Fastening Solutions • 400• Riverwalk Pkwy, Suite 600 ••Tonawanda, NY 14150 • Phone: 866-474-3739 Sherex Fastening Solutions • Phone: 866-474-3739 Fax: 716-875-0358 E-mail:
[email protected] • www.sherex.com RFSL2-580-2.5
M5x0.8 ISO
0.50
0.50
2.50
10.30
14.10
.85
10.95
6.25
www.aboveboardelectronics.com
SHERES f 1.91,111. SOLUTIONS
®
RIV-FLOAT -SHORT RIV-FLOAT® SHORT
series
FLOATING TECHNOLOGIES
RIV-FLOAT®-SHORT vs. Riveted Nut Plates vs. Cage Nuts riveted nut plate
• Requires three holes to be drilled (1 for the plate & 2 for the rivets). • Requires access to both sides of the work piece. • 15-20 second installation time. cage nut
• Requires a square hole to be punched. • Requires access to both sides of the work piece. • 15-20 second installation time. riv-float
- short
®
• Only 1 round hole needs to be drilled. • Access from only one side of the work is necessary for installation. • 2-3 second installation time. Riveted Nut Plate
Cage Nut
Floating Technologies
RIV-FLOAT®-SHORT vs. Riveted Nut Plates RIV-FLOAT®-SHORT
Riveted Nut Plate
holes ®to be drilled (1 for the plate & 2 for the rivets) single kits- Requires – riv-three float - short
- Requires access to both sides of the work piece - 15-20 time • RNHT-0832RFS BAG 1 Installation Tool, 1 second Mandrel,installation 15 Rivfloat Shorts • RNHT-1032RFS BAG 1 Installation Tool, 1 Mandrel, 15 Rivfloat Shorts • RNHT-M4RFSCage BAG 1 Installation Tool, 1 Mandrel, 15 Rivfloat Shorts Nut •- RNHT-M5RFS BAG Hole 1toInstallation Tool, 1 Mandrel, 15 Rivfloat Shorts Requires a Square be punched - Requires access to both sides of the work piece - 15-20 second installation time
multi kits
–
riv-float
- short
®
RIV-FLOAT®-SHORT
• RNHT RFS Inch Kit
1 Installation Tool for 8-32,11round Mandrel, 1 Installation for 10-32, 1 Mandrel, 1 - Only hole needs toTool be drilled Installation Tool for 1/4-20, Mandrel, (30) 6-32,is(30) 8-32, (30)for 10-32 and (20) 1/4-20 - Access from only one1side of the work necessary installation Rivfloat Shorts - 2-3 second installation time
• RNHT RF Metric Kit
1 Installation Tool for M4, 1 Mandrel, 1 Installation Tool for M5, 1 Mandrel, 1 Installation Tool for M6, 1 Mandrel, (40) M4, (30) M5 and (20) M6 Rivfloat Shorts
RIV-FLOAT®-SHORT is installed with a FLEX-5 Hydro-Pneumatic Tool with a RIV-FLOAT®-SHORT Anvil
CENTERING NOSEPIECE
*RIV-FLOAT®-Short is patent pending* Patent Pending
28 SHEREI FASITIVIIC 501,1110149 _
Sherex Fastening Solutions
•
Phone: 866-474-3739 • Fax: Request Info716-875-0358
E-mail:
[email protected] • www.sherex.com •1-800-453-1692 www.aboveboardelectronics.com
LARGE SIZE RIVET NUT SERIES The first product line of its kind offering Rivet Nuts up to ¾-10 (M20)
LARGE SIZE series
features and benefits
• Provide a strong thread in thin sheet materials. • Can be installed from one side of the work piece. • Do not need to be welded to the base material. • Available in a Round Body or a Full Hex Body for increased spin out resistance. • Plated with a RoHS compliant Zinc Trivalent Clear plating.
sizes and styles
• Unified Sizes Available:
• Metric Sizes Available:
- 1/2” Thread Round Body & Hex Body
- M12 Thread Round Body & Hex Body
- 5/8” Thread Round Body & Hex Body
- M16 Thread Round Body & Hex Body
- 3/4” Thread Round Body
Large Size rivet nuts are designed to be installed with the Sherex Flex 18 (see page 42 for details). Sherex Fastening Solutions
•
Phone: 866-474-3739 716-875-0358 • Fax: Request Info
E-mail:
[email protected] • www.sherex.com •1-800-453-1692 www.aboveboardelectronics.com
29
LARGE SIZE series
LARGE SIZE RIVET NUT APPLICATIONS Utility Pole Attachments Utility Pole
Hex Nut
3/4” Round STEP-NUT™
3/4” Step Bolt
Truck Frame Attachments Bracket Bolt
5/8” Full Hex Rivet Nut
Truck Frame
Vending Machine Leg Leveler Bracket
M16 Round Rivet Nut Bolt Leg Leveler
Railcar Attachments Rail Car Frame Bolt
5/8” Round Rivet Nut 30 SHEREI FASITIVIIC 501,1110149
Sherex Fastening Solutions
Rail Car Step •
Phone: 866-474-3739 716-875-0358 • Fax: Request Info
E-mail:
[email protected] • www.sherex.com •1-800-453-1692 www.aboveboardelectronics.com
LARGE SIZE RIVET NUT SPECIFICATIONS Round Body
LARGE SIZE series
GR
yT
HOLE SIZE
L
HD THREAD SIZE
-
lrgr series
round body unified thread LRGR SERIES -- ROUND BODY LRGR SERIES ROUND BODY(unit
-
inches)
Grip LL HD HT DD ILIL Hole Grip Range HD HT HoleSize Size GnpRange VL HoVs Ste SHEREX SHEREX LRGR SERIES -- ROUND BODY LRGR SERIES ROUND BODY Part Thread PartNumber ThreadSize Size Thread Ste Number Min. Max. ±±HD .025 .004 Max. Ref. +.010/-.000 Min. Max. ±.015 .025 ±HT .004 Max. Ref. +.010/-.000 Grip L.015 DD ILIL Hole GripRange Range L HD HT HoleSize Size MVn. Max. ±2015 ± £25 ±± 204 Max. Ref. SHEREX SHEREX Inch -e-Steel Inch Steel Vnch StesV Part Thread PartNumber Number Size ThreadSize Min. Max. .015 .025 .004 Ref. +.010/-.000 Min. Max. ±1.260 .015 ±±.945 .025 ±±.085 .004 Max. Max. Ref. +.010/-.000 LRGR2-5013-150 1/2-13 .050 .150 .656 .656 LRGR2-5013-150 1/2-13UNC UNC .050 .150 ±1.260 .945 .085 .656 .984 .984 .656 Inch Inch--Steel Steel LRGR2-6211-200 5/8-11 .080 .200 .826 .827 LRGR2-6211-200 5/8-11UNC UNC .080 .200 1.428 1.428 1.181 1.181 .098 .098 .826 1.142 1.142 .827 LRGR2-5013-150 1/2-13 .050 .150 .656 .656 LRGR2-5013-150 1/2-13UNC UNC .050 .150 1.260 1.260 .945 .945 .085 .085 .656 .984 .984 .656 LRGR2-7510-250 3/4-10 .010 .250 .906 .907 LRGR2-7510-250 3/4-10UNC UNC .010 .250 1.210 1.210 1.235 1.235 .118 .118 .906 .878 .878 .907 LRGR2-6211-200 5/8-11 .080 .200 .826 .827 LRGR2-6211-200 5/8-11UNC UNC .080 .200 1.428 1.428 1.181 1.181 .098 .098 .826 1.142 1.142 .827 LRGR2-7510-250 3/4-10 .010 .250 .906 .907 LRGR2-7510-250 3/4-10UNC UNC .010 .250 1.210 1.210 1.235 1.235 .118 .118 .906 .878 .878 .907 LL thread HD Grip HT DD - millimeters ILIL Hole HD GripRange Range HT(unit HoleSize Size ) SHEREX SHEREX lrgr series - round body metric Part Thread PartNumber Number Size ThreadSize Min. Max. ±±.38 .64 .10 Ref. +.25/-.000 Min. Max. .38 ±± .64 ±±HT .10 Max. Max. Ref. +.25/-.000 LL HD Grip DD ILIL Hole GripRange Range HD HT HoleSize Size Grog Range VL HoVs Ste SHEREX SHEREX Metric - -Steel Metric Steel Part Thread PartNumber ThreadSize Size Number Thread SVzs Min. Max. ±32.00 ±24.00 .10 Max. Ref. +.25/-.000 Min. Max. ±.38 .38 .64 ±2.16 ±2.16 .10 16.65 Max. 25.00 Ref. +.25/-.000 M. ± 28 24.00 ±.64 ±.10 +.251,000 LRGR2-12175-3.8 M12x1.75 1.27 3.80 16.66 LRGR2-12175-3.8 M12x1.75ISO ISO 1.27 3.80 32.00 16.65 25.00 16.66 Metric Steel Metric Steel Matt--Med LRGR2-1620-5.0 2.00 5.00 21.00 LRGR2-1620-5.0 M16x2.0 M16x2.0ISO ISO 2.00 5.00 36.27 36.27 30.00 30.00 2.50 2.50 20.98 20.98 29.00 29.00 21.00 LRGR2-12175-3.8 1.27 3.80 24.00 2.16 16.66 LRGR2-12175-3.8 M12x1.75 M12x1.75ISO ISO 1.27SERIES 3.80 -32.00 32.00 24.00 BODY 2.16 16.65 16.65 25.00 25.00 16.66 LRGR ROUND LRGR2-1620-5.0 M16x2.0 2.00 5.00 30.00 2.50 20.98 29.00 21.00 LRGR2-1620-5.0 M16x2.0ISO ISO 2.00 5.00 36.27 36.27 30.00 2.50 20.98 29.00 21.00 Grip Range L HD HT D IL Hole Size SHEREX Part Number Thread SizeLRGR SERIES - ROUND BODY Max. -- FULL ±FULL .015 ±HEX .025 ±BODY .004 Max. Ref. +.010/-.000 LRGH SERIES LRGHMin. SERIES HEX BODY Inch - Steel Grip Range L HD HT D IL Hole Size SHEREX LL HD Grip HT Hole HD GripRange Range HT DD(A/F) (A/F) ILIL HoleSize Size(A/F) (A/F) SHEREX SHEREX Part Number Size Thread LRGH SERIES BODY LRGH SERIES FULL HEX BODY LRGR2-5013-150 1/2-13 UNC .050 .150 -- FULL 1.260 HEX .945 .085 .656 .984 .656 Part Thread PartNumber Number Size ThreadSize Min. Max. ± .015 ± .025 ± .004 Max. Ref. +.010/-.000 GR Inch - Steel LRGR2-6211-200 5/8-11 UNC .080 .200 .826 .827 Min. Max. ±1.181 .025 .004 Max. Ref. +.010/-.000 Min. Max. ±1.428 ±.015 ±HD .025 ±±.098 .004 DD Max. Ref. +.010/-.000 L.015 Grip HT (A/F) ILIL Hole Size L HD GripRange Range HT (A/F) 1.142 Hole Size(A/F) (A/F) SHEREX SHEREX L Inch - -Steel Inch Steel LRGR2-7510-250 3/4-10 UNC .010 .250 1.210 1.235 .118 .906 HOLE .878SIZE .907 Part Size Thread PartNumber Number Size ThreadUNC LRGR2-5013-150 1/2-13 .050 .150 1.260 .945 .085 .656 .984 .656 Min. Max. .015 .025 .004 Ref. +.010/-.000 Min. Max. ±1.181 .015 ±1.024 ±1.024 .025 ±±.085 .004 Max. Max. Ref. +.010/-.000 LRGH2-5013-150 1/2-13 .050 .150 .656 .656 LRGH2-5013-150 1/2-13UNC UNC .050 .150 ±1.181 .085 .656 .866 .866 .656 Inch Inch--Steel Steel LRGR2-6211-200 5/8-11 UNC .080 .200 1.428 1.181 .098 .826 1.142 .827 LRGH2-6211-200 5/8-11 .080 .200 .826 .827 LRGH2-6211-200 5/8-11UNC UNC .080 .200 1.260 1.260 1.260 1.260 .118 .118 .826 .965 .965 .827 L HD Grip Range HT D IL Hole Size LRGR2-7510-250 3/4-10 UNC .010 .250 1.210 1.235 .118 .906 .878 .907 SHEREX LRGH2-5013-150 1/2-13 .050 .150 1.024 .085 .656 .866 .656 LRGH2-5013-150 1/2-13UNC UNC .050 .150 1.181 1.181 1.024 .085 .656 .866 .656 Part Number Size Thread HD LRGH2-6211-200 5/8-11 .080 .200 .826 .827 LRGH2-6211-200 5/8-11UNC UNC .080 .200 1.260 1.260 1.260 1.260 .118 .118 .826 .965 .965 .827 Min. Max. ± L.38 ±HD .64 ±HT .10 DDMax. +.25/-.000 Grip (A/F) ILIL Hole Size L HD GripRange Range HT (A/F) Ref. Hole Size(A/F) (A/F) SHEREX SHEREX Metric - Steel L HD Grip Range HT D IL Hole Size SHEREX Part Number Thread Part Number Size ThreadSize Part Number Thread Size LRGR2-12175-3.8 M12x1.75 ISO 1.27 3.80 16.65 16.66 Min. Max. ±32.00 .64 .10 Max. Ref. +.25/-.00 Min. Max. ±.38 .38 ±24.00 ± .64 ±2.16 ±HT .10 DD Max. Ref. +.25/-.00 LL HD Grip (A/F) ILIL Hole Size HD GripRange Range HT (A/F) 25.00 Hole Size(A/F) (A/F) SHEREX SHEREX Metric - -Steel Metric Steel Min. Max. ± .38 ± .64 ± .10 Max. Ref. +.25/-.000 Metric - SteelHT LRGR2-1620-5.0 M16x2.0 ISO 2.00 5.00 36.27 30.00 2.50 20.98 29.00 21.00 Part Thread PartNumber Number Size ThreadSize Min. Max. ±30.00 ±26.00 .10 Max. Ref. +.25/-.00 Min. Max. ±.38 .38 26.00 ±.64 .64 ±2.16 ±2.16 .10 16.65 Max. 22.00 Ref. +.25/-.00 LRGH2-12175-3.8 M12x1.75 1.27 3.80 16.66 LRGH2-12175-3.8 M12x1.75ISO ISO 1.27 3.80 30.00 16.65 22.00 16.66 Metric Metric--Steel Steel LRGR2-12175-3.8 M12x1.75 ISO 1.27 3.80 32.00 24.00 2.16 16.65 25.00 16.66 LRGH2-1620-5.0 2.00 5.00 21.00 LRGH2-1620-5.0 M16x2.0 M16x2.0ISO ISO 2.00 5.00 32.00 32.00 32.00 32.00 3.00 3.00 20.98 20.98 24.50 24.50 21.00 LRGR2-1620-5.0 M12x1.75 M16x2.0 ISO 2.00 5.00 36.27 30.00 2.50 20.98 29.00 21.00 LRGH2-12175-3.8 1.27 3.80 16.66 LRGH2-12175-3.8 M12x1.75 ISO 1.27 3.80 30.00 30.00 26.00 26.00 2.16 2.16 16.65 16.65 22.00 22.00 16.66 lrgh seriesM16x2.0 - full hex body thread (unit LRGH2-1620-5.0 ISO 2.00 5.00 32.00 3.00 24.50 21.00 LRGH2-1620-5.0 M16x2.0 ISO 2.00 5.00 unified 32.00 32.00 32.00 3.00 20.98 20.98 24.50 - inches 21.00 ) LRGH SERIES - FULL HEX BODY
Full Hex Body
SHEREX Part Number Inch - Stad Steel Vold] SHEREX Part Number LRGH2-5013-150 Inch - Steel LRGH2-6211-200
Thread Size Thread Sze LRGH
Grip Range Grog Range
L
HD
HT ET
D IL D(A/F) (N) VL
SERIES - FULL HEX BODY Min. Max. ± .015 ± .025 ± .004 Max.
Hole Size (A/F) Hoe SVze (NE)
Size Thread 1/2-13 UNC 5/8-11 UNC
Grip Range .050 .150 Min. Max. .080 .200
L HD HT D (A/F) 1.181 1.024 .085 .656 ± .015 ± .025 ± .004 Max. 1.260 1.260 .118 .826
Ref. IL .866 Ref. .965
+.010/-.000 +.0101-.000 Hole Size (A/F) .656 +.010/-.000 .827
LRGH2-5013-150
1/2-13 UNC
.050
.150
1.181
1.024
.085
.866
.656
Part Number Metric - Steel SHEREX Part part Number LRGH2-12175-3.8 Metric Steel Metvic - Stec& LRGH2-1620-5.0
Thread Size
Thread Size Thread Ste M12x1.75 ISO M16x2.0 ISO
Min. Max. Grip Range Grhp Range 1.27 3.80 Min. Max. MVn. 2.00 5.00
± .38 L 30.00 ± .38 32.00
± .64 HD 26.00 ± ± .64 24 32.00
± .10 HT 2.16 ± .10 3.00
LRGH2-12175-3.8 LRGH2-1620-5.0
M12x1.75 ISO M16x2.0 ISO
1.27 I 2.00
30.00 32.00
26.00 32.00
2.16 3.00
I
.656
L HD (unit Grip Range HT D-.826 (A/F) IL Hole Size LRGH2-6211-200 UNC hex .080 .200 thread 1.260 1.260 .118 .965 .827 SHEREX lrgh series 5/8-11 - full metric millimeters ) (A/F)
3.80 5.00
Max. Ref. D (A/F) (NE) IL VL 16.65 22.00 Max. Ref. 20.98 24.50 16.65 20.98
22.00 24.50
+.25/-.00 Hole (A/F) Fide Size Ste (NE) 16.66 +.25/-.00 +.25k000 21.00 16.66 21.00
Contact Sherex for test data. Sherex rivet nuts are compatible with the following hardware: GRADE 2, GRADE 5, CLASS 8.8 and CLASS 9.8 Please contact Sherex when using other grade fasteners.
Sherex Fastening Solutions
•
RequestFax: Info 716-875-0358 • www.sherex.com •1-800-453-1692 E-mail:
[email protected] • www.aboveboardelectronics.com
Phone: 866-474-3739
31
.155 .185 When using a pull to stroke installation tool use the following equations to determine approximate stroke distance: 1. (rivet nut max grip) – (actual base material thickness) = (“X”) 2. (“X”) + (pull up factor) = Stroke Distance
NAS/MS FLAT HEAD STYLES Note for Material
NAS/MS
MS/NAS FLAT HEAD STYLES *Note: part numbers reflect steel, open-end, non-keyed, with cadmium yellow plating only. Please refer to part numbering system outline for further configurations.
DFARS
FLAT HEAD STYLES
Compliant to DFARS 252.225-7009
',I I :DE II'..
KEY IrYI
MFR HD MARK
INS R A _L Hol I SIN DETAIL
GRIP
1
ill111
RAD LAI ',ARK IRAD) INI R C.A.T OH MARKS
Produced in our AS9100 Certified manufacturing facility in Akron, Ohio.
CIRC L..M.EIRENTIAL MAYK 1:017C)
J C II A E MAX
OPEN END TYPE
CI GS,L: L Nr) TYPF
TYPICAL INSTALLATION
(unit - inches) Spreadsheet FLAT HEAD COMMON INSTALL HOLE HOLE SSIZE IZE INSTALL Spreadsheet FLAT HEAD NOT COMMON
unified UNIFIED THREAD thread (UNIT-INCHES) Thread Size THREAD Per Mil-‐S-‐SIZE 7742 Min 7 Full Threads
B ØB +/ +/-‐ D INSTALL DRILL CC ØD INSTALL .015 NOM DRILL SIZE .015 NOM ++.000/-.004 .000/ -‐.004 SIZE (REF) (REF)
#4-‐40 UNC-‐3B #6-‐32 UNC-‐3B #8-‐32 UNC-‐3B #10-‐24 UNC-‐3B #10-‐32 UNF-‐3B 1/4-‐20 UNC-‐3B 1/4-‐28 UNF-‐3B 5/16-‐18 UNC-‐3B 5/16-‐24 UNF-‐3B 3/8-‐16 UNC-‐3B 3/8-‐24 UNF 3B 1/2-‐13 UNC-‐3B 1/2-‐20 UNF-‐3B
KEYWAY DETAIL
KEYWAY DIMENSIONS DIMENSIONS KEYWAY
MIN MIN
MAX MAX
E E FF MAX +.005/-.000 MAX +.005/-‐ .000
G P G P MAX MAX ++.003/-.000 .003/-‐.000
.155 .189 .221
.157 .193 .226
0.198 0.240 0.271
0.054 0.054 0.054
0.023 0.023 0.023
H H
*PULL UP FACTOR
0.062 0.062 0.062
.046 -‐ .048 .056 -‐ .058 .056 -‐ .058
.055 .065 .065
0.270 0.325 0.357
0.025 0.032 0.032
0.155 0.189 0.221
5/32 NO 12 NO 2
0.406
0.038
0.250
E
.250 .256 0.302 PART NUMBERING SYSTEM 0.054
0.023
0.062
.056 -‐ .058
.080
0.475
0.058
0.332
Q
.332
.338
0.382
0.054
0.035
0.062
.056 -‐ .058
.095
0.665
0.062
0.413
Z
.413
.423
0.505
0.120
0.040
0.128
.097 -‐ .102
.120
0.781
NUMBERING SYSTEM 0.088 PART0.490 12.5 MM .490
.500
0.597
0.120
0.040
0.128
.110 -‐ .115
.155
0.906
0.085
.635
0.733
0.120
0.040
0.128
.110 -‐ .115
.185
0.625
5/8
.625
part numbering system
Example: SXS2528-80CY CLASSIFICATION CLASSIFICATION SX PART STANDARD
MS27130
Sherex NAS Part
CLASSIFICATION PART STANDARD
PART STANDARD
CLASSIFICATION S 80 CY NAS1329 MS27130 2528 (_) PART STANDARD
MS/NAS FLAT HEAD STYLES
NAS1329
Material Thread Size Grip Range CY-Cadmium Yellow (_) - Open Ended S-Steel Ending in 0 or 5 ZY-Zinc Yellow Non Keyed A-Aluminum denotes Flat Head ML-Mechanical Lock B-Closed End Sherex Fastening Solutions, LLC ~ 400 Riverwalk Pkwy, Suite 600 ~ Tonawanda, NY, 14150 ~ 866-4SHEREX ~ www.sherex.com SS- 430 Stainless Steel K-Keyed NM- 316 Stainless Ending in 1 or 6 R-Ribbed (Non-Magnetic) denotes Countersunk Head CH-Alloy Steel B-Brass
MS/NAS COUNTERSUNK HEAD STYLES
Sherex Fastening Solutions, LLC ~ 400 Riverwalk Pkwy, Suite 600 ~ Tonawanda, NY, 14150 ~ 866-4SHEREX ~ www.sherex.com
PROUDLY MADE IN THE USA
SHEREX FASTENING SOLUTIONS®
CLASSIFICATION PART STANDARD NAS1329
CLASSIFICATION PART STANDARD MS27130 Compliant to DFARS 252.225-7009
Request Info
32 SHEREI FASITIVIIC 501,1110149
1-800-453-1692 Sherex Fastening Solutions • Phone: 866-474-3739 • Fax: 716-875-0358www.aboveboardelectronics.com • www.sherex.com • E-mail:
[email protected]
When using a pull to stroke installation tool use the following equations to determine approximate stroke distance: 1. (rivet nut max grip) – (actual base material thickness) = (“X”) 2. (“X”) + (pull up factor) = Stroke Distance
NAS/MS FLAT HEAD STYLES
Note for Material
*Note: part numbers reflect steel, open-end, non-keyed, with cadmium yellow plating only. Please refer to part numbering system outline for further configurations.
DFARS
FLAT HEAD STYLES
Compliant to DFARS 252.225-7009
MFR HD MARK
NAS/MS
KEY WHEN SPECIFIED
OD
RADIAL MARK (RAD) IDENTIFICATION MARKS ' CIRCUMFERENTIAL MARK (CIRC)
c E MAX
unified thread UNIFIED THREAD (UNIT-INCHES) THREAD SIZE SHEREX PART NUMBER*
THREAD SIZE
SXS4-60CY SXS4-85CY SXS4-110CY SXS4-135CY SXS4-160CY SXS4-185CY SXS6-75CY SXS6-120CY SXS6-160CY SXS6-200CY SXS6-240CY SXS6-280CY SXS8-75CY SXS8-120CY SXS8-160CY SXS8-200CY SXS8-240CY SXS8-280CY SXS1024-80CY SXS10-80CY SXS10-130CY SXS10-180CY SXS10-230CY SXS10-280CY SXS10-330CY
#4-‐40 UNC-‐3B
#6-‐32 UNC-‐3B
#8-‐32 UNC-‐3B
#10-‐32 UNC-3B UNF -‐3B #10-24 #10/24 UNF-3B UNC-‐3B #10-32
I
A
OPEN END TYPE
(unit -
CLOSED END TYPE
TYPICAL INSTALLATION
inches)
OPEN END KEYED KEYED A ND COMMON CLOSED END KEYLESS CLOSED END KEYED OPEN END AND Spreadsheet FLAT HEAD NOT CLOSED END KEYLESS CLOSED END KEYED GRIP RANGE IDENTITIFYING KEYLESS KEYLESS MARK GRIP RANGE IDENTIFYING A M L J K L +/-‐ J K MARK A M L J K L +/J K +/-‐ .015 REF +/-‐ .015 NOM NOM .015 NOM NOM +/- .015 REF +/- .015 NOM NOM .015 NOM NOM .010-‐.060 .060-‐.085 .085-‐.110 .110-‐.135 .135-‐.160 .160-‐.185 .010-‐.075 .075-‐.120 .120-‐.160 .160-‐.200 .200-‐.240 .240-‐.280 .010-‐.075 .075-‐.120 .120-‐.160 .160-‐.200 .200-‐.240 .240-‐.280
BLANK 1 RAD 2 RAD 3 RAD 4 RAD 5 RAD 1 RAD 3 RAD 5 RAD 1 CIRC 2 CIRC PART 3 CIRC 1 RAD 3 RAD 5 RAD 1 CIRC 2 CIRC 3 CIRC
0.345 0.230 0.500 0.370 0.230 0.525 0.400 0.230 0.555 0.425 0.230 0.580 0.450 0.230 0.605 0.480 0.230 0.635 0.438 0.300 0.625 0.500 0.315 0.625 0.500 0.270 0.750 0.562 0.290 0.750 0.625 0.310 0.750 NUMBERING SYSTEM0.812 0.687 0.330 0.438 0.300 0.625 0.500 0.315 0.625 0.500 0.270 0.750 0.625 0.350 0.750 0.625 0.305 0.875 0.687 0.340 0.875
.010-‐.080
BLANK
0.531
0.380
.080-‐.130 .130-‐.180 .180-‐.230 .230-‐.280 .280-‐.330
1 RAD 2 RAD 3 RAD 4 RAD 5 RAD
0.594 0.641 0.703 0.750 0.797
0.390 0.390 0.395 0.395 0.385
0.385 0.385 0.390 0.385 0.385 0.385 0.490 0.440 0.520 0.480 0.435 0.455 0.490 0.440 0.520 0.475 0.555 0.530
0.230 0.230 0.230 0.230 0.230 0.230 0.305 0.255 0.260 0.260 0.260 0.265 0.305 0.255 0.260 0.265 0.310 0.290
0.500 0.525 0.555 0.580 0.605 0.635 0.750 0.750 0.750 0.750 0.750 0.812 0.750 0.750 0.750 0.750 0.875 0.875
0.385 0.385 0.390 0.385 0.385 0.385 0.615 0.565 0.520 0.480 0.435 0.455 0.615 0.565 0.520 0.475 0.555 0.530
0.230 0.230 0.230 0.230 0.230 0.230 0.405 0.355 0.310 0.260 0.260 0.265 0.405 0.355 0.310 0.265 0.310 0.290
0.781
0.630
0.380
0.781
0.630
0.380
0.843 0.891 0.953 1.000 1.047
0.640 0.640 0.645 0.645 0.630
0.390 0.390 0.395 0.395 0.385
0.843 0.891 0.953 1.000 1.047
0.640 0.640 0.645 0.645 0.630
0.390 0.390 0.395 0.395 0.385
1/4-‐20 U NC-‐3B 1/4-28 UNF-3B SXS2528-80CY .020-‐.080 BLANK 0.625 0.450 0.937 0.760 0.440 0.937 0.760 SXS25-80CY 1/4-20 1/4-‐28 UNC-3B UNF-‐3B CLASSIFICATION CLASSIFICATION SXS25-140CY .080-‐.140 1 RAD 0.687 0.450 1.000 0.760 0.440 1.000 0.760 PART1.062 STANDARD PART STANDARD .140-‐.200 SXS25-200CY 2 RAD 0.750 0.450 1.062 0.760 0.440 0.760 SXS25-260CY .200-‐.260 3 RAD 0.812 0.445 1.125 0.755 0.445 1.125 0.755 SXS25-320CY .260-‐.320 4 RAD 0.875 0.445 1.187 0.755 0.445 1.187 0.755 SXS25-380CY .320-‐.380 5 RAD 0.937 0.445 1.250 0.755 0.445 1.250 0.755 5/16-‐18 U NC-‐3B UNF-3B SXS3124-125CY 5/16-24 .030-‐.125 BLANK 0.750 0.505 1.187 0.940 0.550 1.187 0.940 SXS31-125CY 5/16-18 5/16-‐24 UNC-3B UNF-‐3B SXS31-200CY .125-‐.200 1 RAD 0.875 0.555 1.281 0.960 0.555 1.281 0.960 SXS31-275CY .200-‐.275 2 RAD 0.937 0.540 1.343 0.950 0.560 1.343 0.950 SXS31-350CY .275-‐.350 3 RAD 1.032 0.560 1.437 0.965 0.570 1.437 0.965 SXS31-425CY .350-‐.425 4 RAD 1.125 0.580 1.531 0.985 0.575 1.531 0.985 SXS31-500CY .425-‐.500 5 RAD 1.187 0.565 1.593 0.975 0.580 1.593 0.975 3/8-‐16 U NC-‐3B UNF-3B SXS3724-115CY 3/8-24 .030-‐.115 BLANK 0.844 0.585 1.281 1.020 0.660 1.281 1.020 SXS37-115CY 3/8-16 3/8-‐24 UNC-3B UNF-‐3B SXS37-200CY .115-‐.200 1 RAD 0.938 0.595 1.375 1.030 0.670 1.375 1.030 Sherex Fastening Solutions, LLC ~ 400 Riverwalk Pkwy, Suite 600 ~ Tonawanda, NY, 14150 ~ 866-4SHEREX ~ www.sherex.com SXS37-285CY .200-‐.285 2 RAD 1.031 0.605 1.468 1.040 0.680 1.468 1.040 SXS37-370CY .285-‐.370 3 RAD 1.125 0.615 1.562 1.050 0.690 1.562 1.050 SXS37-455CY .370-‐.455 4 RAD 1.218 0.630 1.656 1.065 0.710 1.656 1.065 SXS37-540CY .455-‐.540 5 RAD 1.312 0.635 1.750 1.075 0.715 1.750 1.075 NC-‐3B 1/2-20 U UNF-3B SXS5020-150CY 1/2-‐13 .050-‐.150 BLANK 0.906 0.605 1.328 1.030 0.605 1.328 1.030 SXS50-150CY 1/2-13 1/2-‐20 UNC-3B UNF-‐3B SXS50-250CY .150-‐.250 1 RAD 1.031 0.630 1.453 1.055 0.630 1.453 1.055 SXS50-350CY .250-‐.350 2 RAD 1.141 0.640 1.562 1.060 0.640 1.562 1.060 SXS50-450CY .350-‐.450 3 RAD 1.250 0.650 1.671 1.070 0.650 1.671 1.070
NAS1329
MS27130
MS/NAS COUNTERSUNK HEAD STYLES
Produced in our AS9100 Certified manufacturing facility in Akron, Ohio.
I
I
I
I
J
0.440 0.440 0.440 0.445 0.445 0.445
1
0.550 0.555 0.560 0.570 0.575 0.580 0.660 0.670 0.680 0.690 0.710 0.715
.1
0.605 0.630 0.640 0.650
*Note: Part numbers reflect steel, open-end, non-keyed, with cadmium yellow plating only. Please refer to part numbering system outlined on page 32 for further configurations.
Sherex Fastening Solutions
•
Request Info 1-800-453-1692 • Fax: 716-875-0358 www.aboveboardelectronics.com • www.sherex.com • E-mail:
[email protected]
Phone: 866-474-3739
33
.155 .185 When using a pull to stroke installation tool use the following equations to determine approximate stroke distance: 1. (rivet nut max grip) – (actual base material thickness) = (“X”) 2. (“X”) + (pull up factor) = Stroke Distance
NAS/MS
COUNTERSUNK HEAD STYLES
NAS/MS COUNTERSUNK STYLES Note for Material
MS/NAS FLAT HEAD STYLES *Note: part numbers reflect steel, open-end, non-keyed, with cadmium yellow plating only. Please refer to part numbering system outline for further configurations.
DFARS
Compliant to DFARS 252.225-7009
INSTALL HOLE SIZE DETAIL
MFR HD MARK 1
Produced in our AS9100 manufacturing facility in Akron, Ohio.
CNCL ))).-I'FR PAPAL MAYK ( CRC)
#4-‐40 UNC-‐3B #6-‐32 UNC-‐3B #8-‐32 UNC-‐3B #10-‐24 UNC-‐3B #10-‐32 UNF-‐3B 1/4-‐20 UNC-‐3B 1/4-‐28 UNF-‐3B 5/16-‐18 UNC-‐3B 5/16-‐24 UNF-‐3B 3/8-‐16 UNC-‐3B 3/8-‐24 UNF 3B 1/2-‐13 UNC-‐3B 1/2-‐20 UNF-‐3B
-[ I_
In
J I E MAX
inified thread UNIFIED THREAD (UNIT-INCHES) Thread Size THREAD Per Mil-‐S-‐7742 SIZE Min 7 Full Threads
'
ill111
RADIAL MARK (RAD) I- CAT ON MARKS
LI A
OPEN END TYPE
(unit -
H
rI OTI,E, t' ID I
TYPICAL INSTALLATION
inches)
Spreadsheet INSTALL HOLE SSIZE IZE FLAT HEAD COMMON HOLE Spreadsheet FLAT HEAD NOT INSTALL COMMON
B ØB +/ +/-‐ D INSTALL DRILL CC ØD INSTALL .015 NOM DRILL SIZE .015 NOM ++.000/-.004 .000/ -‐.004 SIZE (REF) (REF)
KEYWAY DETAIL
KEYWAY DIMENSIONS DIMENSIONS KEYWAY
MIN MIN
MAX MAX
E F E F MAX +.005/-.000 MAX +.005/-‐.000
G P G P MAX MAX ++.003/-.000 .003/-‐.000
H H
*PULL UP FACTOR
0.270 0.325 0.357
0.025 0.032 0.032
0.155 0.189 0.221
5/32 NO 12 NO 2
.155 .189 .221
.157 .193 .226
0.198 0.240 0.271
0.054 0.054 0.054
0.023 0.023 0.023
0.062 0.062 0.062
.046 -‐ .048 .056 -‐ .058 .056 -‐ .058
.055 .065 .065
0.406
0.038
0.250
E
.250
.256
0.302
0.054
0.023
0.062
.056 -‐ .058
.080
0.475
0.058
0.332
Q
.332
.338
0.382
0.054
0.035
0.062
.056 -‐ .058
.095
0.665
0.062
0.413
Z
.413
.423
0.505
0.120
0.040
0.128
.097 -‐ .102
.120
0.781
0.088
0.490
12.5 MM
.490
.500
0.597
0.120
0.040
0.128
.110 -‐ .115
.155
0.906
0.085
0.625
5/8
.625
.635
0.733
0.120
0.040
0.128
.110 -‐ .115
.185
PART NUMBERING SYSTEM
PART NUMBERING SYSTEM
part numbering system
Example: SXS2528-80CY CLASSIFICATION SX CLASSIFICATION
PART STANDARD
MS27130
Sherex NAS Part
PART STANDARD
S
CLASSIFICATION 2528 (_) 80
MS27130
PART STANDARD
CY
CLASSIFICATION PART STANDARD
NAS1329
NAS1329
Material Thread Size Grip Range (_) - Open Ended CY-Cadmium Yellow S-Steel Ending in 0 or 5 Non Keyed ZY-Zinc Yellow A-Aluminum denotes Flat Head ML-Mechanical Lock B-Closed End SS- 430 Stainless SteelSherex Fastening Solutions, LLC ~ 400 Riverwalk K-Keyed Pkwy, Suite 600 ~ Tonawanda, NY, 14150 ~ 866-4SHEREX ~ www.sherex.com NM- 316 Stainless Ending in 1 or 6 R-Ribbed (Non-Magnetic) denotes Countersunk Head CH-Alloy Steel B-Brass
MS/NAS FLAT HEAD STYLES
MS/NAS COUNTERSUNK HEAD STYLES
Sherex Fastening Solutions, LLC ~ 400 Riverwalk Pkwy, Suite 600 ~ Tonawanda, NY, 14150 ~ 866-4SHEREX ~ www.sherex.com
PROUDLY MADE IN THE USA
SHEREX FASTENING SOLUTIONS®
CLASSIFICATION PART STANDARD NAS1329
CLASSIFICATION PART STANDARD MS27130 Compliant to DFARS 252.225-7009
34
Request Info 1-800-453-1692 Sherex Fastening Solutions • Phone: 866-474-3739 • Fax: 716-875-0358www.aboveboardelectronics.com • www.sherex.com • E-mail:
[email protected]
NAS/MS COUNTERSUNK HEAD STYLES
NAS/MS
COUNTERSUNK HEAD STYLES
MFR HD MARK
RADIAL MARK IRADI IDENTIFICATION MARKS CIRCUMFERENTIAL MARK (CIRO)
E MAX OPEN END TYPE
CLOSED END TYPE TYPICAL INSTALLATION
UNIFIED THREAD (UNIT-INCHES)
unified thread UNIFIED THREAD (UNIT-INCHES) THREAD SIZE
SHEREX PART NUMBER*
THREAD SIZE
SXS4-81CY SXS4-106CY SXS4-131CY SXS4-156CY SXS4-181CY SXS4-206CY SXS6-106CY SXS6-161CY SXS6-201CY SXS6-241CY SXS6-281CY SXS6-321CY SXS8-106CY SXS8-161CY SXS8-201CY SXS8-241CY SXS8-281CY SXS8-321CY SXS1024-116CY SXS10-116CY SXS10-166CY SXS10-216CY SXS10-266CY SXS10-316CY SXS10-366CY
#4-‐40 UNC-‐3B
#6-‐32 UNC-‐3B
#8-‐32 UNC-‐3B
#10-24 #10-‐32 UNC-3B UNF -‐3B #10-‐24 U NC-‐3B #10-32 UNF-3B
(unit -
inches) OPEN END KEYED AND KEYLESS
CLOSED END KEYLESS
Produced in our AS9100 manufacturing facility in Akron, Ohio.
CLOSED END KEYED
OPEN END KEYED CLOSED END KEYLESS CLOSED END KEYED AND KEYLESS Spreadsheet COUNTERSUNK COMMON A M HEAD NOT L J K L +/J K REF M +/ L .015 NOM J NOM K L .015 +/-‐ NOM J NOM K +/- A .015 +/-‐ .015 REF +/-‐ .015 NOM NOM .015 NOM NOM .050-‐.081 BLANK 0.370 0.235 0.525 0.390 0.235 0.525 0.390 0.235 .081-‐.106 1 RAD 0.395 0.235 0.550 0.390 0.235 0.550 0.390 0.235 .106-‐.131 2 RAD 0.420 0.235 0.575 0.390 0.235 0.575 0.390 0.235 .131 -‐.156 3 RAD 0.450 0.235 0.600 0.390 0.235 0.600 0.390 0.235 .156-‐.181 4 RAD 0.475 0.235 0.625 0.390 0.235 0.625 0.390 0.235 .181-‐.206 5 RAD 0.500 0.235 0.650 0.390 0.235 0.650 0.390 0.235 .065-‐.106 BLANK 0.500 0.325 0.687 0.510 0.325 0.812 0.635 0.425 .106-‐.161 2 RAD 0.500 0.280 0.687 0.465 0.280 0.812 0.590 0.380 .161-‐.201 4 RAD 0.562 0.295 0.687 0.420 0.260 0.812 0.545 0.335 .201-‐.241 1 CIRC 0.625 0.315 0.812 0.505 0.295 0.812 0.505 0.295 .241-‐.281 2 CIRC 0.625 0.270 0.812 0.465 0.265 0.812 0.465 0.265 .281-‐.321 3 CIRC 0.687 0.290 0.844 0.455 0.265 0.844 0.455 0.265 .065-‐.106 BLANK 0.500 0.325 0.687 0.510 0.325 0.812 0.635 0.425 .106-‐.161 2 RAD 0.500 0.280 0.687 0.465 0.280 0.812 0.590 0.380 .161-‐.201 4 RAD 0.562 0.290 0.687 0.415 0.255 0.812 0.540 0.330 NUMBERING SYSTEM .201-‐.241 1 CIRC PART0.625 0.310 0.875 0.560 0.290 0.875 0.560 0.290 .241-‐.281 2 CIRC 0.687 0.325 0.875 0.515 0.290 0.875 0.515 0.290 .281-‐.321 3 CIRC 0.687 0.295 0.875 0.485 0.300 0.875 0.485 0.300
GRIP RANGE
IDENTITIFYING IDENTIFYING MARK MARK
.065-‐.116
BLANK
0.578
0.395
0.828
0.645
0.395
0.828
0.645
0.395
.116-‐.166 .166-‐.216 .216-‐.266 .266-‐.316 .316-‐.366
1 RAD 2 RAD 3 RAD 4 RAD 5 RAD
0.625 0.687 0.734 0.781 0.844
0.385 0.400 0.390 0.385 0.400
0.875 0.938 0.984 1.031 1.094
0.635 0.650 0.640 0.635 0.650
0.385 0.400 0.390 0.385 0.400
0.875 0.938 0.984 1.031 1.094
0.635 0.650 0.640 0.635 0.650
0.385 0.400 0.390 0.385 0.400
GRIP RANGE
1/4-‐20 UNF-3B UNC-‐3B 1/4-28 SXS2528-151CY .089-‐.151 BLANK 0.687 0.440 1.000 0.750 0.435 1.000 0.750 CLASSIFICATION SXS25-151CY 1/4-20 1/4-‐28 UNC-3B UNF-‐3B CLASSIFICATION SXS25-211CY PART STANDARD.151-‐.211 1 RAD 0.750 0.440 1.062 0.750 0.435PART 1.062 0.750 STANDARD SXS25-271CY .211-‐.271 2 RAD 0.812 0.440 1.125 0.750 0.435 1.125 0.750 SXS25-331CY .271-‐.331 3 RAD 0.875 0.435 1.187 0.750 0.435 1.187 0.750 SXS25-391CY .331-‐.391 4 RAD 0.937 0.435 1.250 0.750 0.435 1.250 0.750 SXS25-451CY .391-‐.451 5 RAD 1.000 0.435 1.312 0.760 0.445 1.312 0.760 5/16-‐18 UNF-3B UNC-‐3B SXS3124-181CY 5/16-24 .106-‐.181 BLANK 0.844 0.540 1.218 0.915 0.540 1.218 0.915 SXS31-181CY 5/16-18 5/16-‐24 UNC-3B UNF-‐3B SXS31-256CY .181-‐.256 1 RAD 0.937 0.560 1.312 0.935 0.560 1.312 0.935 SXS31-331CY .256-‐.331 2 RAD 1.000 0.550 1.406 0.955 0.550 1.406 0.955 SXS31-406CY .331-‐.406 3 RAD 1.093 0.565 1.468 0.940 0.565 1.468 0.940 SXS31-481CY .406-‐.481 4 RAD 1.156 0.555 1.562 0.960 0.555 1.562 0.960 SXS31-556CY .481-‐.556 5 RAD 1.250 0.575 1.625 0.950 0.575 1.625 0.950 3/8-24 UNF-3B 3/8-‐16 U NC-‐3B SXS3724-211CY .125-‐.211 BLANK 0.938 0.580 1.375 1.020 0.655 1.375 1.020 SXS37-211CY 3/8-16 3/8-‐24 UNC-3B USherex NF-‐3B Fastening Solutions, LLC ~ 400 Riverwalk Pkwy, Suite 600 ~ Tonawanda, NY, 14150 ~ 866-4SHEREX ~ www.sherex.com SXS37-296CY .211-‐.296 1 RAD 1.031 0.590 1.468 1.030 0.655 1.468 1.030 SXS37-381CY .296-‐.381 2 RAD 1.125 0.600 1.562 1.040 0.675 1.562 1.040 SXS37-466CY .381-‐.466 3 RAD 1.219 0.615 1.656 1.050 0.690 1.656 1.050 SXS37-551CY .466-‐.551 4 RAD 1.312 0.625 1.750 1.065 0.705 1.750 1.065 .551-‐.636 5 RAD 1.442 0.650 1.859 1.090 0.715 1.859 1.090 SXS37-636CY 1/2-‐13 UNF-3B UNC-‐3B 1/2-20 SXS5020-226CY .125-‐.226 BLANK 0.984 0.610 1.406 1.030 0.610 1.406 1.030 SXS50-226CY 1/2-13 1/2-‐20 UNC-3B UNF-‐3B SXS50-326CY .226-‐.326 1 RAD 1.094 0.620 1.515 1.040 0.620 1.515 1.040 SXS50-426CY .326-‐.426 2 RAD 1.218 0.640 1.625 1.050 0.640 1.625 1.050 SXS50-526CY .426-‐.526 3 RAD 1.312 0.635 1.750 1.075 0.635 1.750 1.075
MS27130
NAS1330
FLEX-5 HYDRO-PNEUMATIC TOOL
0.435 0.435 0.435 0.435 0.435 0.445 0.540 0.560 0.550 0.565 0.555 0.575 0.655 0.655 0.675 0.690 0.705 0.715 0.610 0.620 0.640 0.635
*Note: Part numbers reflect steel, open-end, non-keyed, with cadmium yellow plating only. Please refer to part numbering system outlined on page 34 for further configurations.
Request Info 1-800-453-1692 Sherex Fastening Solutions • Phone: 866-474-3739 • Fax: 716-875-0358 www.aboveboardelectronics.com • www.sherex.com • E-mail:
[email protected]
35 SHERES 1,91,111.
CAL KITS - LARGE FLANGE, KNURLED CAL KITS
cal rivet nut hand tool kit
Sherex Part Number
Kit Contents
tilft aW,21!;1 414
Kit Contents
CAL RNHT LRG IN KIT
50 pieces of CAL2-0632-080 40 pieces of CAL2-0832-080 40 pieces of CAL2-1032-130 1 RNHT-0632 Tool 1 RNHT-0832 Tool 1 RNHT-1032 Tool
30 pieces of CAL2-2520-165 20 pieces of CAL2-3118-150 20 pieces of CAL2-3716-150 1 RNHT-2520 Tool 1 RNHT-3118 Tool 1 RNHT-3716 Tool
Kit Contents
(unit -
metric)
CAL RNHT SML MET KIT
CAL RNHT LRG MET KIT
50 pieces of CAL2-470-2.0 40 pieces of CAL2-580-3.3 1 RNHT-M4 Tool 1 RNHT-M5 Tool
30 pieces of CAL2-610-4.2 20 pieces of CAL2-8125-3.8 20 pieces of CAL2-1015-3.8 1 RNHT-M6 Tool 1 RNHT-M8 Tool 1 RNHT-M10 Tool
cal rivet nut kit
Sherex Part Number
inches)
CAL RNHT SML IN KIT
cal rivet nut hand tool kit
Sherex Part Number
(unit -
(unit -
inches)
CAL SML IN KIT
CAL LRG IN KIT
50 pieces of CAL2-0632-080 40 pieces of CAL2-0832-080 40 pieces of CAL2-1032-130
30 pieces of CAL2-2520-165 20 pieces of CAL2-3118-150 20 pieces of CAL2-3716-150
11M111. alliE6 1111111 1 11 11 A1/47177 41121111
cal rivet nut kit
Sherex Part Number Kit Contents
(unit -
metric)
CAL SML MET KIT
CAL LRG MET KIT
50 pieces of CAL2-470-2.0 40 pieces of CAL2-580-3.3
30 pieces of CAL2-610-4.2 20 pieces of CAL2-8125-3.8 20 pieces of CAL2-1015-3.8
Request Info
36 SHEREI FASITIVIIC 501,1110149
1-800-453-1692 www.aboveboardelectronics.com Sherex Fastening Solutions • Phone: 866-474-3739 • Fax: 716-875-0358 • www.sherex.com • E-mail:
[email protected]
CAH KITS - HALF HEX, LARGE FLANGE
cah rivet nut hand tool kit
Sherex Part Number
Kit Contents
Kit Contents
CAH RNHT LRG IN KIT
50 pieces of CAH2-0632-080 40 pieces of CAH2-0832-080 40 pieces of CAH2-1032-130 1 RNHT-0632 Tool 1 RNHT-0832 Tool 1 RNHT-1032 Tool
30 pieces of CAH2-2520-165 20 pieces of CAH2-3118-150 20 pieces of CAH2-3716-150 1 RNHT-2520 Tool 1 RNHT-3118 Tool 1 RNHT-3716 Tool
Kit Contents
Kit Contents
metric)
30 pieces of CAH2-610-4.2 20 pieces of CAH2-8125-3.8 20 pieces of CAH2-1015-3.8 1 RNHT-M6 Tool 1 RNHT-M8 Tool 1 RNHT-M10 Tool
(unit -
inches)
CAH SML IN KIT
CAH LRG IN KIT
50 pieces of CAH2-0632-080 40 pieces of CAH2-0832-080 40 pieces of CAH2-1032-130
30 pieces of CAH2-2520-165 20 pieces of CAH2-3118-150 20 pieces of CAH2-3716-150
cah rivet nut kit
Sherex Part Number
(unit -
CAH RNHT LRG MET KIT
cah rivet nut kit
Sherex Part Number
inches)
CAH RNHT SML IN KIT
cah rivet nut hand tool kit
Sherex Part Number
(unit -
CAH KITS
(unit -
metric)
*a l4143M.V ' ''1471:42C
CAH LRG MET KIT
30 pieces of CAH2-610-4.2 20 pieces of CAH2-8125-3.8 20 pieces of CAH2-1015-3.8
Request Info
1-800-453-1692 www.aboveboardelectronics.com Sherex Fastening Solutions • Phone: 866-474-3739 • Fax: 716-875-0358 • www.sherex.com • E-mail:
[email protected]
37 SHERES h9YEMAIG
RIVET NUT HAND TOOLS HAND TOOLS
LHF TOOLS LHF 202 (Imperial Tool) Includes: 8-32, 10-24, 1/4-20 head sets LHF 202M (Metric Tool) Includes: M4, M5, M6 head sets This hand tool was designed to install any rivet nut ranging in size from 6-32 to 1/4-28 (M4-M6), and is ideal for small production work and prototyping. riv-float®
standard Thread Size 6-32 8-32 10-24 10-32 1/4-20 1/4-28 5/16-18 5/16-24 3/8-16 3/8-24 1/2-13 1/2-20 M4 M5 M6 M8 M10
riv-float®-short
Mandrel Anvil Thread Size Mandrel Anvil LHFM 0632 LHFA 0632 LHFM 2528 LHFA 25 6-32 LHFM 0832 LHFA 0832 8-32 LHFM 2528 LHFA 25 LHFM 1024 LHFA 10 LHFM 1032 LHFA 10 10-32 LHFM 1032 LHFA 10RF LHFM 2520 LHFA 25 1/4-20 LHFM 2520 LHFA 25RF LHFM 2528 LHFA 25 M4 LHFM 2528 LHFA 25 LHFM 3118 LHFA 31 M5 LHFM M5 LHFA M5RF LHFM 3124 LHFA 31 M6 LHFM M6 LHFA M6RF LHFM 3716 LHFA 37 LHFM 3724 LHFA 37 LHFM 5013 LHFA 50 LHFM 5020 LHFA 50 LHFM M4 LHFA M4 LHFM M5 LHFA M5 LHFM M6 LHFA M6 M5 Hand Tool LHFM M8 Ratchet StyleLHFA HandM8 Installation tool designed for small production work and prototyping LHFM M10 LHFA M10
Thread Size 8-32 10-32 M4 M5
Mandrel
Anvil
LHFM 0832 LHFM 1032 LHFM M4 LHFM M5
LHFM 0832RFS LHFM 1032RFS LHFM M4RFS LHFM M5RFS
Anvil
Mandrel
M4 AND M5 TOOL
Installation Sizes: 6-32 to 3/8-24 (M4 – M10) M5 (Imperial Tool) Includes: 10-32, 1/4-20, 5/16-18, and 3/8-16 head sets M5 (Metric Tool) Includes: M5, M6, M8, and M10 head sets
riv-float®
standard RATCHET STYLE
M5 HAND TOOL HEAVY DUTY
M4 HAND TOOL
Thread Size
Head Sets (Includes Anvil & Mandrel)
Anvil
Mandrel
6-32 8-32 10-24 10-32 1/4-20 1/4-28 5/16-18 5/16-24 3/8-16 3/8-24 1/2-13 1/2-20 M4 M5 M6 M8 M10 M12
MHS-0632 MHS-0832 MHS-1024 MHS-1032 MHS-2520 MHS-2528 MHS-3118 MHS-3124 MHS-3716 MHS-3724 MHS-5013 MHS-5020 MHS-M4 MHS-M5 MHS-M6 MHS-M8 MHS-M10 MHS-M12
MA-0632 MA-0832 MA-1024 MA-1032 MA-2520 MA-2528 MA-3118 MA-3124 MA-3716 MA-3724 MA-5013 MA-5020 MA-M4 MA-M5 MA-M6 MA-M8 MA-M10 MA-M12
M-0632 M-0832 M-1024 M-1032 M-2520 M-2528 M-3118 M-3124 M-3716 M-3724 M-5013 M-5020 M-M4 M-M5 M-M6 M-M8 M-M10 M-M12
Thread Size
Head Sets
(Includes Anvil & Mandrel)
8-32 10-32 1/4-20 M4 M5 M6
MHS-0832RF MA-2520/2528 MHS-1032RF MA-1032RF MHS-2520RF MA-2520/2528RF MHS-M4RF MA-2520/2528 MHS-M5RF MA-M5RF MHS-M6RF MA-M6RF
M-2528 M-1032 M-2520 M-2528 M-M5 M-M6
riv-float®-short Thread Size
Head Sets
Anvil
(Includes Anvil & Mandrel)
8-32 10-24 10-32 M4 M5
Mandrel
MHS-0832RF MA-0832RFS MHS-1024RFS MA-10RFS MHS-1032RF MA-10RFS MHS-M4RFS MA-M4RFS MHS-M5RFS MA-M5RFS
M-0832 M-1024 M-1032 M-M4 M-M5
M4 (Imperial Tool) Includes: 1/4-20, 5/16-18, 3/8-16, and 1/2-13 head sets M4 (Metric Tool) Includes: M6, M8, M10, and M12 head sets M5 (Imperial Tool) Includes: 10-32, 1/4-20, 5/16-18, and 3/8-16 head sets M5 (Metric Tool) Includes: M5, M6, M8, and M10 head sets
RNHT TOOL riv-float®
standard Part Number RNHT-0632 RNHT-0832 RNHT-1024 RNHT-1032 RNHT-2520 RNHT-2528 RNHT-3118 RNHT-3124 RNHT-3716 RNHT-3724 RNHT-4320 RNHT-M3 RNHT-M4 RNHT-M5 RNHT-M6 RNHT-M8 RNHT-M10
38 SHEREI FASITIVIIC 501,1110149
Request Info
Thread 6-32 8-32 10-24 10-32 1/4-20 1/4-28 5/16-18 5/16-24 3/8-16 3/8-24 7/16-20 M3 M4 M5 M6 M8 M10
Thread Size
Part Number
6-32 8-32 10-32 1/4-20 M4 M5 M6
RNHT-2528RF RNHT-2528RF RNHT-1032RF RNHT-2520RF RNHT-2528RF RNHT-M5RF RNHT-M6RF
riv-float®-short Thread Size
M4 M5
Part Number
RNHT-M4RFS RNHT-M5RFS
1-800-453-1692
RIVET NUT PNEUMATIC SPIN - SPIN TOOLS
RIVET NUT PNEUMATIC
SPIN-SPIN TOOLS Designed for installing steel or aluminum CAL, CAK, CAH, CAO, CFT/CAT*, CFW/CAW* and CPB rivet nut inserts. Features quick change nose piece for head set replacement without tools. *Can install stainless steel.
SSG-900 INLINE STYLE SERIES
k • SSG-910 RIGHT ANGLE STYLE SERIES
SSG-800 PISTOL STYLE SERIES
' 11I
Part Number
SSG - 801, 901 & 911
Thread Size
Tool RPM
Air Pressure (Dynamic)
Weight
Air Inlet
Air Use
Minimum Hose Size
Complete Head Assembly
Hex Driver
Mandrel
Bearing Set
801&901/911
PSI
LBS
NPT
CFM
IN
4-40
3000/2200
35-45
3.0
1/4"
5
3/8
HS-0440
HD-4
M-0440-150
BS-4
6-32
3000/2200
70-80
3.0
1/4"
5
3/8
HS-0632
HD-6
M-0632-150
BS-6
8-32
3000/2200
70-90
3.0
1/4"
5
3/8
HS-0832
HD-8
M-0832-150
BS-8
M3
3000/2200
35-45
3.0
1/4"
5
3/8
HS-M3
HD-M3
M-M3-30
BS-M3
M4
3000/2200
35-45
3.0
1/4"
5
3/8
HS-M4
HD-M4
M-M4-35
BS-M4
Complete Head Assembly Rivet Nut Stud
Make Up Complete Head Assembly
HSS-0632
802&902/912
SSG - 802, 902 & 912
10-24
1500/1100
60-80
3.0
1/4"
5
3/8
HS-1024
HD-10
M-1024-175
BS-10
10-32
1500/1100
60-80
3.0
1/4"
5
3/8
HS-1032
HS-10
M-1032-175
BS-10
HSS-1032
1/4-20
1500/1100
70-90
3.0
1/4"
5
3/8
HS-2520
HD-25
M-2520-175
BS-25
HSS-2520
1/4-28
1500/1100
70-90
3.0
1/4"
5
3/8
HS-2528
HD-25
M-2528-200
BS-25
M5
1500/1100
60-80
3.0
1/4"
5
3/8
HS-M5
HD-M5
M-M5-40
BS-M5
HSS-M5
M6
1500/1100
70-90
3.0
1/4"
5
3/8
HS-M6
HD-M6
M-M6-40
BS-M6
HSS-M6
803&903/913
SSG - 803, 903 & 913
SSG - 804
SSG-808
5/16-18
600/400
90-110
3.0
1/4"
5
3/8
HS-3118
HD-31
M-3118-175
BS-31
5/16-24
600/400
90-110
3.0
1/4"
5
3/8
HS-3124
HD-31
M-3124-175
BS-31
3/8-16
600/400
90-110
3.0
1/4"
5
3/8
HS-3716
HD-37
M-3716-200
BS-37
3/8-24
600/400
90-110
3.0
1/4"
5
3/8
HS-3724
HD-37
M-3724-200
BS-37
M8
600/400
90-110
3.0
1/4"
5
3/8
HS-M8
HD-M8
M-M8-40
BS-M8
M10
600/400
90-110
3.0
1/4"
5
3/8
HS-M10
HD-M10
M-M10-45
BS-M10
5/16-18
600
90-110
3.0
1/4"
5
3/8
HS-3118
HD-31
M-3118-175
BS-31
5/16-24
600
90-110
3.0
1/4"
5
3/8
HS-3124
HD-31
M-3124-175
BS-31
3/8-16
600
90-110
3.0
1/4"
5
3/8
HS-3716
HD-37
M-3716-200
BS-37
3/8-24
600
90-110
3.0
1/4"
5
3/8
HA-3724
HD-37
M-3724-200
BS-37
M8
600
90-110
3.0
1/4"
5
3/8
HS-M8
HD-M8
M-M8-40
BS-M8
M10
600
90-110
3.0
1/4"
5
3/8
HS-M10
HD-M10
M-M10-45
BS-M10
1/2-13
275
75-120
4.0
1/4"
5
3/8
HS-5013
HD-50
M-5013-250
BS-50
1/2-20
275
75-120
4.0
1/4"
5
3/8
HS-5020
HD-50
M-5020-225
BS-50
M12
275
75-120
4.0
1/4"
5
3/8
HS-M12
HS-M12
M-M12-60
BS-M12
HSS-3716 HSS-M8
HSS-M8
*Contact SherexSherex for other thread *Contact forsizes Prebulbed (CPB) Mandrel part numbers
Contact SHEREX for SSG Replacement part numbers. *Weight for 800 series only. High temperature grease should be used to lubricate the bearing set. Contact Sherex for availability. Sherex recommends the use of an air regulator, air filter, and lubrication system to reduce the wear of internal components. It is also recommended to lubricate the mandrel to increase performance. Mandrels should be replaced when excessive thread wear occurs with a high quality socket head cap screw.
Request Info
1-800-453-1692 www.aboveboardelectronics.com
39
HYDRO-PNEUMATIC FLEX-5 TOOL FLEX-5 TOOL
One Tool With Pull to Pressure & Pull to Stroke Capabilities FLEX-5S: The Sherex FLEX-5S utilizes a Pull to Stroke method of installation. This method allows the insert to be installed to the same distance each time. This is helpful when installing into soft materials (prevents crushing of the base material) or when a specific Installed Length is required.
FLEX-5P: The Sherex FLEX-5P utilizes a Pull to Pressure method of installation. This method allows the same insert type to be installed into varying material thicknesses (within the Grip Range of the part) without any adjustment to the tool.
*View our FLEX-5 videos at www.sherex.com features and benefits
Change over kit for converting between pull to pressure and pull to stroke • • • • • • • •
Installs Rivet Nuts from: M3-M10 and #4-40-3/8-16. Push to start nose piece to spin on fastener. Single stage trigger. Automatic reverse with manual reverse bypass. Quick change mandrel design. Light weight (4.2 lbs). Can be suspended from a balancer. Socket head cap screw mandrel. 1/2
• Installs Rivet Nut Studs from M5-M8 and #10-24-5/16-24. • Available in an in-line version. • Split tool available (remote booster for lighter tool). • Upgradeable to process monitoring. • 5,000 lbs (22 kN) pulling force at 90 psi. • 7 mm (0.276 in.) of available stroke. • 2-3 second cycle time. • All aluminum design for improved durability.
5
3
4
STANDARD HEAD SET
head sets for standard rivet nuts Thread Size
40
Complete Headset
Anvil (1 + 2)
Mandrel (3)
Hex Driver (4)
Reducing sleeve (5)
M3
FL5 - HS - M3
FL5 - HS - 00903
M -M3 -40
FL5 - HS - 01003
FL5 - HS - 09103
M4
FL5 - HS - M4
FL5 - HS - 00904
M -M4 - 55
FL5 - HS - 01004
FL5 - HS - 09104
M5
FL5 - HS - M5
FL5 - HS - 00905
M -M5 - 65
FL5 - HS - 01005
FL5 - HS - 09105
M6
FL5 - HS - M6
FL5 - HS - 00906
M -M6 - 65
FL5 - HS - 01006
FL5 - HS - 09106
M8
FL5 - HS - M8
FL5 - HS - 00908
M -M8 - 65
FL5 - HS - 01008
FL5 - HS - 09108
FL5 - HS - 01010
n/a
M 10
FL5 - HS - M10
FL5 - HS- 00910
M -M10 - 65
# 4- 40 UNC
FL5 - HS - 0440
FL5 - HS- 00854
M -0440 - 175
FL5 - HS - 00754
FL5 - HS - 09154
# 6 -32 UNC
FL5 - HS - 0632
FL5 - HS - 00856
M -0632 - 175
FL5 - HS - 00756
FL5 - HS - 09156
# 8 -32 UNC
FL5 - HS - 0832
FL5 - HS - 00858
M -0832 - 175
FL5 - HS - 00758
FL5 - HS - 09158
# 10-24 UNC
FL5 - HS - 1024
FL5 - HS -00850
M -1024 - 250
FL5 - HS - 00750
FL5 - HS - 09150
FL5 - HS - 00750
FL5 - HS - 09150
FL5 - HS - 00748
FL5 - HS - 09148
# 10-32 UNF
FL5 - HS - 1032
FL5 - HS - 00850
M -1032 - 250
1/4-20 UNC
FL5 - HS - 2520
FL5 - HS - 00848
M -2520 - 250
1/4-28 UNF
FL5 - HS - 2528
FL5 - HS - 00848
M -2528 - 250
FL5 - HS - 00748
FL5 - HS - 09148
5/16-18 UNC
FL5 - HS - 3118
FL5 - HS - 00840
M -3118 - 250
FL5 - HS - 00740
FL5 - HS - 09140
5/16-24 UNF
FL5 - HS - 3124
FL5 - HS - 00840
M -3124 - 250
FL5 - HS - 00740
FL5 - HS - 09140
FL5 - HS - 00742
n/a n/a
3/8-16 UNC
FL5 - HS - 3716
FL5 - HS - 00842
M -3716 - 250
3/8-24 UNF
FL5 - HS - 3724
FL5 - HS - 00842
M -3724 - 25 0
FL5 - HS - 00742
Thread Size
Complete Headset
Anvil
Mandrel (3)
Hex Driver (4)
Request Info (1 + 2)
Reducing sleeve
1-800-453-1692 (5) www.aboveboardelectronics.com
1/4-28 UNF
FL5 - HS - 2528
FL5 - HS - 00848
M -2528 - 250
FL5 - HS - 00748
FL5 - HS - 09148
FL5 - HS - 00740
FL5 - HS - 09140
5/16-18 UNC
FL5 - HS - 3118
FL5 - HS - 00840
M -3118 - 250
3/8-16 UNC
FL5 - HS - 3716
FL5 - HS - 00842
M -3716 - 250
FL5 - HS - 00742
n/a
3/8-24 UNF
FL5 - HS - 3724
FL5 - HS - 00842
M -3724 - 25 0
FL5 - HS - 00742
n/a
Thread Size
Complete Headset
Anvil (1 + 2)
Mandrel (3)
Hex Driver (4)
5 TOOL & HYDRO-PNEUMATIC M -3124 - 250 5/16-24 UNF FL5 - HS - 3124 FL5 - HSFLEX- 00840
head sets for rivet nut studs
MS RIVETFL5 NUT TOOL FL5 -100 HS - 00740 - HS - 09140
Reducing sleeve (5)
M5
FL5 - HS - M5S
FL5 - HS - S0905
FL5 - HS - 0S005
FL5 - HS - 01010
M6
FL5 - HS - M6S
FL5 - HS - S0906
FL5 - HS - 0S006
FL5 - HS - 01010
n/a
M 8*
1/2
n/a
FL5 - HS - S0908
FL5 - HS - 0S008
FL5 - HS - 01010
n/a
# 10-24 UNC
FL5 - HS - 1024S
FL5 - HS - S0850
FL5 - HS - S1024
FL5 - HS - 01010
n/a
# 10-32 UNF
FL5 - HS - 1032S
FL5 - HS - S0850
FL5 - HS - S1032
FL5 - HS - 01010
n/a
1/4-20 UNC 1/4-28 UNF
FL5 - HS - 2520S
FL5 - HS - S0848
FL5 - HS - S2520
FL5 - HS - 01010
n/a
FL5 - HS - 2528S
FL5 - HS - S0848
FL5 - HS - S2528
FL5 - HS - 01010
n/a
5/16-18 UNC *
F L5- HS - 3118S
FL5 - HS - S0840
FL5 - HS - S3118
FL5 - HS - 01010
n/a
5/16-24 UNF *
FL5 - HS - 3124S
FL5 - HS - S0840
FL5 - HS - S3124
FL5 - HS - 01010
n/a
Reducing sleeve (5) Reducing sleeve (5)-09148 F L 5-HS
FL5 - HS - M8S
FLEX-5 TOOL
4
3
STUD PULLER
*Head sets include p/n FL5-HS-12S92 adaptor nut head sets for riv-float®
1/2
Anvil (1 + 2) Anvil (1 +-00848 2) F L 5-HS
Mandrel (3) Mandrel (3) M-2528-225
Hex Driver (4) Hex Driver (4)-00748 F L 5-HS
F L 5-HS -R 0995 F L 5-HS -00848 F L 5-HS -R 0996 F L 5-HS -R 0995 F L 5-HS -00848 F L 5-HS -R 0996 F L 5-HS -00848 F L 5-HS -00848 F L 5-HS -00848 F L 5-HS -00848 F L 5-HS -R 0950 F L 5-HS -00848 F L 5-HS -R 0950 F L 5-HS -R 0950 F L 5-HS -R 0948 F L 5-HS -R 0950 F L 5-HS -R 0948 F L 5-HS -R 0948
M-M5-65 M-2528-225 M-M6-65 M-M5-65 M-2528-225 M-M6-65 M-2528-225 M-2528-225 M-2528-225 M-2528-225 M-1024-250 M-2528-225 M-1032-250 M-1024-250 M-2520-250 M-1032-250 M-2528-250 M-2520-250
F L 5-HS -01005 F L 5-HS -00748 F L 5-HS -01006 F L 5-HS -01005 F L 5-HS -00748 F L 5-HS -01006 F L 5-HS -00748 F L 5-HS -00748 F L 5-HS -00748 F L 5-HS -00748 F L 5-HS -00750 F L 5-HS -00748 F L 5-HS -00750 F L 5-HS -00750 F L 5-HS -00748 F L 5-HS -00750 F L 5-HS -00748 F L 5-HS -00748
1/4-28 F L 5-HS -2528R 1 F L 5-HS -R 0948 M-2528-250 8-32 UNFMA-207-0832 MA-157-0832 Anvil head sets forComplete riv-float®short Mandrel Thread 10-24 SizeMA-209-1024Headset MA-159-1032 (1 + 2) (3) 10-32 MA-162-1032 MA-159-1032 Anvil Mandrel Complete Thread 1/4-20 SizeMA-211-2520 MA-161-2520 F L 5-HS -M4S R F L 5-HS -S 2) R 0994 M-M4-55 (1 + (3) Headset M4
F L 5-HS -00748 Hex Driver (4) Hex Driver (4)-01004 F L 5-HS
M-M5-65 M-M4-55 M-0832-150 M-M5-65 M-1024-225 M-0832-150 M-1032-225 M-1024-225
F L 5-HS -01005 F L 5-HS -01004 F L 5-HS -00758 F L 5-HS -01005 F L 5-HS -00750 F L 5-HS -00758 F L 5-HS -00750 F L 5-HS -00750
F L 5-HS -09105 F L 5-HS -09104 F L 5-HS -09158 F L 5-HS -09105 F L 5-HS -09150 F L 5-HS -09158 F L 5-HS -09150 F L 5-HS -09150
M-1032-225
F L 5-HS -00750
F L 5-HS -09150
Thread Size Thread Size
M4 M5 M4 M6 M5 # 4-40 M6UNC # 6-32 # 4-40 UNC UNC # # 8-32 6-32 UNC UNC ##10-24 UNC 8-32 UNC # 10-24 10-32 UNC UNF # 1/4-20 UNC # 10-32 UNF 1/4-28Size UNF Thread 1/4-20 UNC 6-32
Complete Headset Complete Headset F L 5-HS -2528R F L 5-HS -M5R F L 5-HS -2528R F L 5-HS -M6R F L 5-HS -M5R F L 5-HS -2528R F L 5-HS -M6R F L 5-HS -2528R F L 5-HS -2528R F L 5-HS -2528R F L 5-HS -2528R F L 5-HS -1024R F L 5-HS -2528R F L 5-HS -1032R F L 5-HS -1024R F L 5-HS -2520R F L 5-HS -1032R MS 50 F L 5-HS -2528R Mandrel Anvil1 F L 5-HS -2520R
MA-364-0632
MA-367-0632
1/4-28 MA-362-2528 MA-161-2520 F L 5-HSMA-368-3118 -M5S R F L 5-HS -S R 0995 M5 5/16-18 MA-365-3118 F L 5-HS -M4S R F L 5-HS -S R 0994 M4 5/16-24 MA-366-3124 MA-368-3118 F L 5-HS -0832S R F L 5-HS -S R 0858 # 8-32 UNC F L 5-HSMA-357-3716 -M5S R F L 5-HS -S R 0995 M5 3/8-16 MA-358-3716 F L 5-HS -1024S R F L 5-HS -S R 0950 ##10-24 3/8-24 UNC MA-363-3724 MA-357-3716 F L 5-HS -0832S R F L 5-HS -S R 0858 8-32 UNC M3 MA-203-03MM F L 5-HSMA-213-03MM -1032S R F L 5-HS -S R 0950 # 10-32 UNF F L 5-HSMA-214-04MM -1024S R F L 5-HS -S R 0950 # 10-24 M4 UNC MA-204-04MM M5 MA-205-05MM MA-215-05MM F L 5-HS -1032S R F L 5-HS -S R 0950 # 10-32 UNF M6 MA-206-06MM MA-216-06MM M8 MA-208-08MM MA-218-08MM M10 MA-210-10MM MA-220-10MM
F L 5-HS -09105 F L 5-HS -09148 F L 5-HS -09106 F L 5-HS -09105 F L 5-HS -09148 F L 5-HS -09106 F L 5-HS -09148 F L 5-HS -09148 F L 5-HS -09148 F L 5-HS -09148 F L 5-HS -09150 F L 5-HS -09148 F L 5-HS -09150 F L 5-HS -09150 F L 5-HS -09148 F L 5-HS -09150 F L 5-HS -09148 F L 5-HS -09148
5
3
4
RIV-FLOAT® HEAD SETS
F L 5-HS -09148 Reducing sleeve (5) Reducing sleeve (5)-09104 F L 5-HS
ms 100 rivet nut tool Thread Size 5/16-18 5/16-24 3/8-16 3/8-24 7/16-14 7/16-20 1/2-13 1/2-20 M8 M10 M12 M14
MS100 Mandrel MA-373-3118 MA-377-3124 MA-374-3716 MA-378-3724 MA-375-4314 MA-301-4320 MA-376-5013 MA-379-5020 MA-308-08MM MA-310-10MM MA-312-12MM MA-314-14MM
Anvil MA-369-3118 MA-369-3118 MA-370-3716 MA-370-3716 MA-371-4314 MA-371-4314 MA-372-5013 MA-372-5013 MA-318-08MM MA-320-10MM MA-322-12MM MA-324-14MM
The MS 100 Rivet Nut installation tool installs rivet nuts from 5/16-18 to 1/2-20 and M8 and M14. It also installs 5/16 -18 and M8 Riv-Float®. The MS 100 tool comes with one mandrel and one anvil. The MS 100 Rivet Nut installation tool should be operated at 80-100 psi. Sherex recommends the use of an air regulator, air filter and lubrication system to reduce the wear of internal components. It is also recommended to lubricate the mandrel to increase performance. Mandrels should be replaced when excessive thread wear occurs.
Request Info
1-800-453-1692 www.aboveboardelectronics.com
41
HYDRO-PNEUMATIC FLEX - 18 TOOL FLEX18 TOOL
features and benefits
The most powerful tool on the market providing Pull to Pressure and Pull to Stroke installation capabilities. • • • • • • • • • • • • •
Installs Rivet Nuts from M8 to M16 and 5/16-18 to 3/4-10. Push to start nose piece to spin on fastener. Single stage trigger. Automatic reverse with manual reverse bypass. Quick change mandrel design. Socket head cap screw mandrel for sizes up to M12 and 1/2-20. Can be suspended from a balancer. 18,000 lbs. (80 kN) of pulling force. 15 mm (.591 in) of available stroke. Upgradeable to process monitoring. 2-3 second cycle time. Light weight handle (8.0 lbs.). All aluminum handle design for improved durability.
FL EX-18 SE RIES HEAD SE T C OMP ONEN TS
FL EX-18 SE RIES HEAD SE T C OMP ONEN TS
head sets for standard size nose case Thread Size
Mil
Complete Headset
Thread Size M8
Complete Headset FL18 - H S -M8
M10 M8
FL18 - H- SH-M10 FL18 S -M8
Anvil
Anvil
Hex Driver
Mandrel
Hex Driver
Mandrel
Adaptor Nut
Adaptor Nut
FL18 - H S -00908
M -M8 -65
FL5 - H S -010 08
FL18 - H-SH-00910 FL18 S -00908
M -MM10-65 -M8 -65
FL5 -FL5 H S -- 01010 H S -09110 H S -010 08FL18 -FL18 - H S -09108
M -MM12-65 - H S--01012 H S -09112 -M 10-65 FL18 FL5 H S - 01010FL18 -FL18 - H S -09110
M12 M10
FL18 SS -M12 FL18- H -H -M10
FL18 - H-SH-00912 FL18 S -00910
5/16 -18 M12UNC
FL18 -H S -3118 FL18 -H S -M12
FL18 - H S -09108
5/16 -24 UNF
FL18 - H S -3124
FL18 - H-SH-00908 - H S -00740 H S -09108 FL18 S -00912 M -3118 M -M-250 12-65 FL5 FL18 - H S -01012FL18 -FL18 - H S -09112 FL18 - H S -00908 M -3124 -250 FL5 - H S -00740 FL18 - H S -09108
3/8-16 UNC
FL18 - H S -3716
FL18 - H S -00910
M -3716 -300
FL5 - H S -00742
FL18 - H S -09110
3/8-24 UNF
FL18 - H S -3724
FL18 - H S -00910
M -3724 -300
FL5 - H S -00742
FL18 - H S -09110
1/2-13 UNC
FL18 - H S -5013
FL18 - H S -00950
M -5013 -300
FL18 - H S -00750
FL18 - H S -09150
1/2-20 UNF
FL18 - H S -5020
FL18 - H S -00950
M -5020 -300
FL18 - H S -00750
FL18 - H S -09150
5/16 -18 UNC 5/16 -24 UNF 3/8-16 UNC 3/8-24 UNF
1/2-13 UNC 1/2-20 UNF
FL18 - H S -3118
FL18 - H S -3124 FL18 - H S -3716 FL18 - H S -3724
FL18 - H S -5013 FL18 - H S -5020
FL18 - H S -00908 FL18 - H S -00908
FL18 - H S -00910 FL18 - H S -00910
FL18 - H S -00950 FL18 - H S -00950
M -3118 -250 M -3124 -250
FL5 - H S -00740
FL18 - H S -09108
FL5 - H S -00740
FL18 - H S -09108
FL5 - H S -00742
FL18 - H S -09110
FL5 - H S -00742
FL18 - H S -09110
M -5013 -300
FL18 - H S -00750
FL18 - H S -09150
M -5020 -300
FL18 - H S -00750
FL18 - H S -09150
M -3716 -300
M -3724 -300
Complete Anvil nose Mandrel Thread Size head sets for large size case Headset
Complete Headset
M16 Size Thread
FL18 - H S -M16
FL18 - H SAnvil -00916
M -M 16-F L 18 Mandrel
5/8-11 UNC
FL18 - H S -6211
FL18 - H S -00962
M -6211 -FL18
M16UNC 3/4-10
FL18 -H S -M16 FL18 -H S -7510
FL18 S -00916 M -7510 M -M-FL18 16-F L 18 FL18 - H-SH-00975
5/8-11 UNC
FL18 - H S -6211
FL18 - H S -00962
M -6211 -FL18
3/4-10 UNC
FL18 - H S -7510
FL18 - H S -00975
M -7510 -FL18
View our FLEX-18 tool demonstration at at www.Sherex.com Request Info 42 SHEREI FASITIVIIC 501,1110149 _
1-800-453-1692 www.aboveboardelectronics.com
VALUE PROPOSITIONS
FASTENING SYSTEMS ENGINEERED FOR PERFORMANCE™ Benefits of Full Hex Rivet Nuts vs. Welded Hex Fasteners
The challenge: • This new process replaced the previous welding A manufacturer of agricultural equipment was experiencing process, increasing throughput by 50%. insufficient throughput rates in its baler product lines. • Additionally, the new solution eliminated all emissions • The issue was determined to be a result of the welding and vapors associated with the welding process, which led process used in the numerous attachment points. to a safer working environment for the assemblers. • The manufacturer wanted to improve the work The savings: environment by reducing the amount of emissions and Annual usage of the rivet nuts: 1,000,000 vapors caused by the welding process.
Cost savings: $0.12 per weld = $120,000 annual savings!
The solution: Working directly with the manufacturer, the Sherex engineering team designed a new line of full hex rivet nuts Sherex is a global manufacturer with a unique market to meet the application performance requirements. approach in engineered fastening solutions that combines fasteners, tooling, and automation to deliver the best • The new full hex rivet nuts significantly increased the solution at the lowest total installed cost. application spin out resistance during installation. • Sherex provided a complete installation solution to the customer: full hex rivet nuts and the FLEX-5 tool.
Benefits of In-Die Fastener Installation vs. Welded Fastener Methods
0
e"
Lowest Tote f
Installed Cost
The challenge: A manufacturer of automotive safety systems was experiencing a high fallout rate at the attachment point of the seat belt retractor assembly. • The failure was determined to be a result of the secondary welding process that was required to attach the nut to the sheet metal component. • This process caused a very high percentage of thread damage and distortion of the welded nut. The solution: Sherex introduced the manufacturer to an MDS automation in-die fastener installation system. • By utilizing the MDS automation installation system and incorporating a clinch nut design into the seat rail, the manufacturer was able to produce the sheet metal stamping and place the fastener in the same operation.
• This improvement eliminated the welding process that caused the thread damage. • The new clinch nut automated process simplified the component manufacturing process by reducing the number of required steps and reduced on-site inventory. The savings: Annual part assemblies: 450,000
Cost savings: $0.37 per part = $166,500 annual savings! Sherex is a global manufacturer with a unique market approach in engineered fastening solutions that combines fasteners, tooling, and automation to deliver the best solution at the lowest total installed cost.
These are illustrative examples of actual experiences and are intended for sales purposes only.
Request Info
1-800-453-1692 www.aboveboardelectronics.com
43
TESTING METHODS TESTING METHODS
pull out
Definition: • Pull Out occurs when threads are pulled from the rivet nut (ultimate thread strength) or base material is distorted and the entire rivet nut pulls through the base material. Causes: • Hole size is too large. • Forces applied to the joint are higher than anticipated.
spin out
Definition: • Spin Out is the amount of torque required to make a rivet nut spin in the hole it was installed in. Causes: • Bolt cross threads into the rivet nut causing it to spin. • Excessive corrosion causes bolt to bind in the nut. • Using a screw with mechanical locking feature that has higher prevailing torque than the spin out of the rivet nut. torque out
Definition: • Torque force required to strip threads out of the rivet nut. • This method of testing sandwiches the head of the rivet nut between the non-rotational mating part and parent or base panel. • Spin Out is not a factor because tightening the bolt on the non-rotating part holds the rivet nut in place and prevents it from spinning. Causes: • Assembly torque is too high causing thread failure. • Improper grade of fastener used. *Torque can be affected by various factors such as coefficient of friction of the finish, prevailing torque, washers, etc… Sherex recommends you test your application. suggested assembly torque
Definition: • Recommended torque for assembling a rivet nut joint with class 8.8/grade 5 hardware. Contact Sherex should you require Grade 8, Class 10 or higher joint strength.
44
S
SUGGESTED ASSEMBLY TORQUE
THREAD SIZE
INCH LBS. -Nm PLATED SCREW GRADE 5 CLASS 8.8
# 6-32 UNC # 8-32 UNC # 10-24 UNC # 10-32 UNF 1/4-20 UNC 1/4-28 UNF 5/16-18 UNC 5/16-24 UNC 3/18-16 UNC 3/8-24 UNF M4x0.7 ISO M5x0.8 ISO M6x1.0 ISO M8x1.25 ISO M10x1.5 ISO M12x1.75 ISO
12 22 32 36 75 75 156 156 276 276 2.5 5.0 8.6 21.0 42.0 72.0
TEST DATA IS FOR REFERENCE ONLY. SHEREX RECOMMENDS TESTING YOUR APPLICATION FOR AN EXACT FIGURE.
Request Info
1-800-453-1692
CUSTOM PRODUCT SHOWCASE Sherex has the capability to create custom products for our customers; our in-house engineering and manufacturing teams work with customer to create specialized fastening solutions. Here are some examples of custom products created by Sherex:
CUSTOM PRODUCT SHOWCASE
M6 stud was developed for an attachment point to a truck frame. Design incorporated wedgehead feature for increased spin out resistance and the MAThread® screw design for reduced cross thread risk during assembly. Application incorporated Sherex Process Monitoring Tooling to ensure each part was properly installed.
Was developed to attach a molded plastic cover to a base unit. If the rivet nut has an outside thread to accept a nut, the plastic cover could be altered and the external thread of the rivet nut could be used for the attachment point.
Designed with an extra large head to act like a spacer.
Sherex developed this part to add increased spin out resistance in soft materials. Special knurl design provides increased engagement with the base material. Small flange provided near flush installation.
Special small grip part designed for materials thinner than .030 inches.
A replacement for a more expensive, machined component that would periodically spin-out. The customer required a low-profile insert with high spin-out resistance. Sherex developed this part has a half-hex body to increase spin performance, 0.145” max installed length, and higher strength threads to withstand installation forces.
* MAThread® is a registered trademark of MAThread Inc.
Request Info
1-800-453-1692 www.aboveboardelectronics.com
45
CUSTOM PRODUCT SHOWCASE
CUSTOM PRODUCT SHOWCASE Sherex has the capability to create custom products for our customers; our in-house engineering and manufacturing teams work with customer to create specialized fastening solutions. Here are some examples of custom products created by Sherex:
Sherex developed a high strength rivet nut that is compatible with class 10.9 bolts. This design incorporates a full hex body for increased spin out resistance. It also ensures the bolt is the failure mode, which is a best practice when working with structural applications.
Special head and wedge design to meet spin-out requirements in an application.
Sherex shouldered rivet nut was developed for attachments in plastics. The shoulder design provides a positive metal to metal installation redirecting the load of the joint through the rivet nut shoulder. This minimizes the plastic from creeping during assembly and maintains joint clamp load.
M6 prebulbed slotted body design incorporated under head wedges to increase the spin out resistance in soft plastic.
5/16-18 prebulbed slotted body style with a trimmed head. This head feature allowed installation in the field by the consumer or assembler when used with a special low cost installation tool. Feature also allows head to sit flush within a slot to prevent spin out.
Closed end design with o-ring and o-ring recess under head provides the ultimate sealing solution for attachment points in applications with chemicals and other fluids that breakdown other sealing compounds.
Request Info 46
1-800-453-1692 www.aboveboardelectronics.com
ENGINEERING GUIDE ENGINEERING GUIDE design support capabilities
• Sherex combines design & engineering support to ensure the end user is using the correct fastener for the application. • Sherex utilizes Solidworks 3D modeling.
sherex production
• Sherex Production Capabilities - Multi-station progressive forming machines for deep extrusions • Production methods used: - Machining - Tapping - Drilling - Stamping - Assembly - Additional supporting equipment
sherex quality
• Statistical Process Control (SPC) - Used in the manufacturing process - Critical for use in Level 3, Rev 4 PPAP • Sherex quality labs use the latest in testing equipment to ensure our products meet stringent quality requirements. • Computerized tensile machine • Standard measuring equipment • Salt spray booth • Gauging equipment • Torque testing • Advanced optical sorting equipment is available for automotive and critical parts
Request Info
1-800-453-1692 www.aboveboardelectronics.com
47
1/64 .0180
.0156 .457
.396 47
.0160
.406
78
48 .0785 5/64
.0760 1.994
1.93018
.0781
1.984
20 .1695 19
.1610 4.305
4.089
.1660
4.216
.508 46 .0810 2.057 11/64 .1719 4.366 SHEREX DECIMAL EQUIVALENTS & DRILL SIZE CHART 77 .0180 .457 47 .0785 1.994 18 .1695 4.305
.0200
.0210
.533
.0225
.572
76 75
.0240
.0860
43
.0890
42Size
(Dec.) .0935
.533
.0250Size
(Dec.) .635
(mm)
.026080
.0135 .660
.343
.0240
72 79
44
.0210
Inch .0225 Metric
73
.0820
.508
.609
Drill 74
45
.0200
.572 Drill .609
3/3250
.0250 .368 .0145
.635
49
71
.0156 .0260 .396
48
.0160 .742
.660
.406
77
.0180
.457
.02801/64
.711
.029278 70
.0280
.031069
.787
41
40 .711
.031275 68
.792 .0210 .0310 .533
.032074
1/32 73
.330 72 67
.0225 .813
.0312
.0240
37 .792
.609
.838
66 .035071
38 .787
.572
.660
.036065
.0280
.711
69
64 .037068
.0292
.742
.0360 .787 .940 .0310
.914 34
.0312 .0370 .792
.940 33
.0350 .914
1/32 63
.0380
.965
67
.0320
62 .039066
.813
.0380
.991 .330
61 .040065 59
.0370
.940
58 61
.0380 1.067
.965
1.041
.0420 .991 .0390
1.067
.0400 .0430 1.016
1.092
1.181
1.041
.0410
.042062 .0430
1.092
60 57
.046559
1.181 .0410
1.041
.046958
.0420 1.191
1.067
.052056
55
1.321 1.181 .0465 .0520 .0469 1.397
1.191
55
.059553
.0520
1.321
.0625 53 1/16
1.588 .0595 .0625 1.511
56
.0465
3/64 57
.05503/64 54 54
.0469 1.092 .0430 .0550
1.511
.0595 1.397 .0550
1/16
.063552
.0625
1.588
52
.067051 51
.0635
1.613
1.702 .0670 1.702 .0670
Gauge
1.613 .0635
Gauge 10 (B & S) 12
0.101
110.0907
11
13
13 15
16
0.072
17
0.0641
.0960 .0760
1.930 .0938
.0781 .0980 41
2.527
2.578 2.083 .0995 .1015
2.261
2.705
.104 2.375
(Dec.) 14
22
.1570 13
3/16
4.305
11
4.801 .1875
.1910
4.851 4.801 P .1890 K .2810 7.137
12 4.366
I
.2720
J
.2770
6.909O
4.763
7.036
.1935 4.394 11
4.915 21/64 9/32 .2812 4.851 7.142 .1910
16
4.496 .1960
4.978 .1935
15
.1770 9
2.578
10
.1800
4.572
8
.1990
14 2.642 .1820
9 4.623
L
.2900
M
.2950
7.366Q
4.915
7.493
5.055
R
.1960 .2969 4.978 19/64 7.541
(mm) 7.541
31/64 .3020.4844
12.304 7.671
M
.2950
19/64 1/2
.2969 12.700 .5000
.3125.5156
33/64 N
7.938
7.541
.3020 13.096 7.671
17/32 .3160.5312
13.492
35/64
13.891
5/16
7.493
.31258.026 7.938
.5469
39/64
.6094
7/64 .1100
21/32
.6562
16.667
.0980
.1100 2.819 2.527
12
.1890
4.801
O
.3160
43/64
.6719
17.066
39
35 .1110 .0995
2.489
38
.1015 34
.1130
2.578 .1110
10 2.819 .1935
4.915 6
45/64 T
.7031 .3580 17.859
33 .1160 .1065
2.946 2.705
8.611
47/64
.7344
.3480 5.410 8.839
49/64 3/8
.7656 .3750 19.446 9.525
9.093
25/32
.3770.7812
9.576 19.842
9.129W
51/64 .3860.7969
20.241 9.804
2.870
.104
36
2.642
.1130
32 .1094 .1200
.1160 2.779 3.048
.1100 31
35
2.794 .1200
.1250 .1110
3.175
1/8
.1360
.2055
2.870 4
7
2.946.2010
3
4 5.105 .2130
.1960
5.159 3
7/32 .2040 .2055 2
5.220 .2210
4 3.264 .2090
3
2 5.309
1
A
.2340
7/32
A .2188
3.264 3.571
2
3.571.2280
5.613 .2344
3.658 3.569 .1440
1
.2210 15/64
A
3.658.2340
B
.2380 5.944 B
.1406 .1470 26
27
27
3.571 3.734
.1470
.1440
.1495 25
3.658
3.861 3.797 .1520
3.797
3.734 C
23/64 .3594 5.613
5.791
.2340 5.558 15/64 5.791
V
5.944 .3770
W 5.954 .3860
6.045 .3970
X .2380
5.954 .2420
Y
.4040
.2380
6.045
13/32
.4062
.2500 6.248 1/4
6.350 7/16 27/64 .4219 6.350 10.716 .2500
D 3.797.2420
C
.2460
.1520
.1540 23
3.861
1/4
.2500
7/16
.4375
.1540
.1562 5/32 .1562
3.912
3.967 .1562 3.967
E
3.912 E
6.350
.2500
F 3.967.2570
6.350
.2570 F 6.528
29/64
.4531
Steel
Steel
&(U.S. S) 0.1345 Std.) (U.S. Std.)
0.0897 0.0598
22
9.921
11.509
Steel
0.0285 Gauge (B &0.0329 S) (B & S) Gauge
.4062.8906 10.317 22.621
59/6
.4040 22.22510.262 .8750
57/64 13/32
.4062
10.317
29/32 .4130.9062
Z
59/64
23.017 10.490 .4130 10.490 15/1
.9219
23.416
.4375.9531 11.113 61/64 24.20911.113 7/16 .4375 31/32
.9688
24.608
63/64
.9844
25.004
11.908 15/32 .4688 1.46881.000 25.40011.908 Steel Steel (U.S. Std.) (U.S. Std.)
0.0897
0.0403
0.0478
19
0.0359
0.0418 0.0359
0.0113
260.0100 27 28 29 30
7/8
29/3
Y 7/8
0.0269
250.0126
55/6
57/6
10.084
0.0209 0.0226
28
27/3
23.829 10.262
.3970
230.0179 240.0142
53/6
10.084 21.433
X
26 27
49/6
55/64 .4040.8594
25
0.0159
3/4
23 24 25 26 27 28 29 30
0.0269
0.0179
0.0201 0.0164 0.0149 0.0179
0.0226 0.0201 0.0179
0.0135 0.0159
0.0159 0.0120 0.0142 0.0126 0.0113 0.0100
31/3
.4531 .4531 11.50911.509 63/6 6.35029/64 29/64
6.528 15/32 .2570 15/32 .4688 6.528 11.908
Aluminum
0.0226
43/6
.3970.8438 27/32
0.1046
18
0.0418 0.0320
.8281 .3906 21.034 9.921
.3906
0.0299 0.0299
0.0538
0.0478
53/64 25/64
0.0253 0.0253 0.0239
0.0453
0.0538
.3860 20.638 9.804 .8125
22
0.0598
0.0359 0.0598
6.350 .2500
11.113
Aluminum No. of (B & S) No. of Aluminum (U.S. Std.) 0.0253
9.576
W 13/16
220.0201
0.0508
0.0673 0.0418
10.317
.3770
24
23
30
0.0538 0.0747
10.262Z
6.147
V
0.0329 0.0329
0.1196
0.072
21
21/3
18.654
U .3680 19.050 9.347 3/4 .3750.7500 9.525
0.0299 0.0285 0.0285
0.0907 0.1196 0.0897 0.0673
No. of Gauge
41/6
S.3580.6875 .34809.093 11/16 17.463
21
0.1345
0.1046
F
.2500 E
11/32 .3480 .34388.839 8.733
21
0.1196 0.1010.1345 0.1046
1/4 D 3.861 .2460
5/8
6.248 6.24827/64 27/64 .4219 .4219 10.71610.716 61/6 .2460 Z .4130 10.490 15/16 .9375 23.813
.1520 .1495 24
C
D 6.147
6.147 .2420
13/32
10.084 6.045
.2344
24
5/325/32 1.702
9.804 Y
B
25
3.912 .1540
9.576 X
5.944
15/64
.1495 3.734
23
25/64
.2344 .3906 5.954 25/64 9.921
.1470
26
V
5.558
.3750 5.791 9.525
3.569 3.175 .1406 3.454
5.558 .3580
3/8 .2280
.1285 .1406
9/63 .1360
T
.2188
5.410 1
.1405 .1250
3.569
S .2130
.3680 5.613 9.347
9/6330
.1405
.3390
.2210 U
28 1/8
28
R
.2090 .3438 5.309 11/32 8.733 5.410 3/8
.2280
3.454.2130
S
39/6
8.839 25/3 5.220 23/64 .3594 9.129 9.093 51/6 Q .3320 8.433 23/32 .7188 18.258 .2055 23/64 5.309 5.220 U .3680 .35949.347 9.129 13/1
.2188
7/32
8.026
.2031 P 5.182 .3230 5.159 8.204 T
5.182
3.175
5.105
21/64 8.334 .2040 .3281 5.182
5
.2090 5.055
.1990
13/64 3.048.2031 5
3.454
5
8
2.870 3.264 3.048 .1360
13/64 .2040 4.851 4.978
6
.1285 2.946
.1200 29
31
9
2.819
.1250
30 .1160
6 11 2.794 .1910
.2010 5.159
19/3
15.479
41/64 16.271 8.611 R.3438.6406 .33908.733
7 .2031
37/6
.3390.6250 47/6 .33208.611 15.875 8.433
Q 5/8
.3125
2.779 13/64
9/1
19/32 15.083 .3320.5938 21/64 .32818.433 8.334 23/3
N 5.105 .3020 5.055 7.671 .1990 11/32 7.938
35/6
.3230 .31608.204 8.026 11/1 .5625 14.288 37/64 14.684 8.204 45/6 P.3281.5781 .32308.334 O 9/16
5/16
.1094 2.794
13 2.705 .1850 7
29
S,
5/16
6.756 4.700
3/16
0.0142 0.0126 0.0113 0.0100
0.0239 0.0209 0.0179 0.0164 0.0149 0.0135 0.0120
0.0269 0.0239 0.0209 0.0179 0.0164 0.0149 0.0135 0.0120
0.0359
Request Info 48
4.763 .2660
H .1850
Size .2969(Dec.)
4.763
29
0.101 (B
6.630N
10 17 2.527 .1730
0.0673
0.0320
4.216 .1890
.1695
2.489.1719 11/64
0.0359
200.0359
.1660
.2610 4.700
7.493
Inch .2900 Metric 7.366
4.700 8 .2010
9/63
0.0320
.1875
G
.1820 .2656 4.623 17/64 6.746
4.089 13
2.43812
0.0403 0.0571 0.0478
0.0508
14 4.039
20 2.383 .1610
19
0.0571
3.988 .1850
(mm) 19/64
.2950
Drill L
7.366
.1875
.1130 .1285
23 1.613
Size4.623 (Dec.)
15
M
.2900
7.142
3/16
.1440 .1405
0.0453
(mm) .1820
2.261
21 2.375 .1590
18
4.572
Metric 16
L
.2812
7.137
2.438
37
2.383 .1065 2.779
.1800
Size
19
4.496
.2810
.0960
40
.0938 36 .1094
28
0.0508
1.984 2.489
.0960
.1065 37 .0935
1.321
0.072
2.438
1.994
38
29
0.0808
.0935 1.854
15
1815
0.0403
20
1.778 2.383
.1770
Drill2.184 Inch
0.0747
0.0453
19
.0700 .0938
1.191
0.0907
(mm) 2.375
16
0.0641
17
18
4.572
0.0571
20
17
.1800
0.0641 0.0808 0.0747
16
16
.0890
1513
14
14
43
1412
0.0808
12
Metric 4.496
No. of Aluminum SteelStd.) (B & Aluminum S) (U.S. Gauge 1110
10
Drill .1770 Inch
2.261
.0890
41
Aluminum
No. of
Metric .0860
32
24 1.588
7.142
Inch 44
33
25 1.511
.2812
4.394
30
26 1.397
9/32
.1730
2.184 2.642
1/8 34
27
7.137
17
.0860 .104
31
1.016
.2810
2.083
2.184
.1015 .0820 39
.991 7/64
.0360 .0400 .914
.041063
No. of
.965 32
.838
.0390 .0350 1.016 .889
64 60
.889 35
K
9/32
.0820
44
.838 7/643/32
.0260 .330 .889
70
7.036
45
45
42
.2770
4.366
.0980 2.057
36 .813
J
.1719
.0810
.0320 .635 .0250
6.909
11/64
.0995 40
43
4.394
.2720
2.057
.0785
46
.1730
K
I
.0810
3/32
47
17
H.2770 .26607.036 6.756
46
42 .0730
5/64
39 .742
.0292 .508 .0200
76
2.083
J
1-800-453-1692 www.aboveboardelectronics.com
1
ADDITIONAL SHEREX SERVICES
ADDITIONAL SHEREX SERVICES
sherex website
•
000 1
• Complete product catalog.
F.TF_NIXOSTSIEMS ENONE.. FOR PERFORMMCE
• Download the catalog, drawings, installation methods and installation videos.
• Links to the 3D models.
installed 3d model download
a• m om.orC.,
• Choose your: style of interest, type of material, material thickness, open or closed end, and thread size.
0
• Create an installed 3D model of the fastener for placement into your modeling system. • The model is available in 21 different file formats.
CAP
Poralat
Rem< select
r Do nM
sak are 0g0111 Pump Ns season
d coal-Au-dn.
Add part to caddl,
• Models are available for the Imperial/Inch body style Full Hex rivet nuts, RIV-FLOAT® and Brass Inserts.
marketing tools
Fastener Sample Plate
• Features installed samples of standard rivet nuts, clinch nuts, Tubtara® rivet nuts, RIV-FLOAT® rivet nuts, and Sherex specials.
Sherex Sample Kits
• Contains various samples of Sherex brand fasteners. Ideal for countertop displays.
Sherex Literature Sr
• Sherex offers a wide variety of product catalogs, sell sheets, brochures, value propositions, and much more.
SHEREX
Request Info
1-800-453-1692 www.aboveboardelectronics.com
"" Sip,-0111 1110.—
91.ERES A9.EFICIG SOLIMONS
49
® SHEREX RHEREK FASTENING FG\OTECK2 SOLUTIONS BOLUMMR,
HEADQUARTERS:
SHEREX FASTENING SOLUTIONS, LLC 400 Riverwalk Pkwy, Suite 600 Tonawanda, NY 14150 Phone: 866-474-3739 Fax: 716-875-0358 E-mail:
[email protected] www.sherex.com
PRODUCTION FACILITIES:
SHEREX AKRON
850 Moe Drive Akron, OH 44310 Phone: 330-630-2293 Fax: 716-875-0358
SHEREX TAIWAN
No. 201, Sandong Road Chungli City Taoyuan District, Taiwan 32053 Phone: +886 3-498-8689 Fax: +886 3-498-3543 E-mail:
[email protected] ADDITIONAL LOCATIONS:
SHEREX MEXICO S. DE R.L. DE C.V. Circuito Balvanera 5A Bodega 11 Parque Industrial Balvanera Corregidora, Queretaro C.P. 76900 Mexico Phone: +52 (442) 196-8354 E-mail:
[email protected] ALL INFORMATION IN THIS CATALOG IS SUBJECT TO CHANGE WITHOUT NOTICE.
Request Info
C-RN 3/2015
1-800-453-1692 www.aboveboardelectronics.com
AS9100, ISO 9001:2008 AND ISO/TS 16949:2009 CERTIFIED