Prewire for Models 100, 106, 300, 500, 504, 511, etc. Prewire for all “Pan”, “TES2”, ‘’Vik”, “Elan”, etc.
Holovision Face Plate
Holovision Rough-in Box
From Main Equipment Area
Cat 5/6 (communication) Cat 5/6 (spare)
NOTE: Wires shown in red are the minimum required Wires shown in blue are recommended
Page 1
This document is property of Holovision, and may not be reproduced without permission.
1 IC only
Prewire for Models 100-VIO2, 106-VIO2, 300-VIO2, 420-VIO2, 421-VIO2
Holovision Face Plate
Holovision Rough-in Box
From Main Equipment Area
Cat 5/6 (communication)
VIO2
Cat 5/6 (spare)
NOTE: Wires shown in red are the minimum required Wires shown in blue are recommended
Page 2
This document is property of Holovision, and may not be reproduced without permission.
1 IC only
Door Station Rough-in
Model 100, 101, 106, 107, 400, 410, 500, 504, 511
50” NOTE: All dimensions given are relative to “finished” surface, not rough grade.
*NOTE: Model 501 requires separate push button. Locate push button near door at approximately 40” above finished surface
Page 3
This document is property of Holovision, and may not be reproduced without permission.
1 IC only
Installation Details - 300 and 600 Series Stone Pilaster Installation
1 3/4” reveal at top of box (beyond surface of finished masonry)
58” to top of box
Finished elevation
Installation on smooth wall
1 3/4” reveal at top of box (beyond surface of finished masonry)
58” to top of box
Installation on stone wall
Page 4
Finished elevation
This document is property of Holovision, and may not be reproduced without permission.
1 IC only
Installation Details - 2 Piece Gooseneck
OPTION -conduit to gate. See second page for more details
Center of Rough-in template is 19” from edge of the curb (This will allow 1/2 of the intercom box to overhang) 48” to center
Gooseneck Rough-in Template
2” to top of rough-in template from surface of driveway
(this will place center of intercom box at 48”)
Ground level
Surface of finished driveway
Conduit to gate
Conduit to house
ROUGH-IN BRACKET INSTALLATION
Hand hole in pole Ground level
Conduit to gate (optional)
Use 3 or 4 bags of ready mix cement
Conduit to house
NOTE: PVC elbows must be facing in proper direction to minimize 900 bends in conduit to gooseneck
DETAIL OF ATTACHMENT OF POLE ONTO BASE Page 5
This document is property of Holovision, and may not be reproduced without permission.
1 IC only
Installation Details - 2 Piece Gooseneck Optional application with 2 conduits
2” Steel Gooseneck Pole
Cover for access door
NOTE: BE SURE THAT CONDUITS ARE SECURED BEFORE POURING CONCRETE. LARGE CONDUIT MUST BE PLUMB IN ORDER TO FIT INSIDE 2” GOOSENECK MOUNTING POLE
3/4” LB shown with male adapter, close nipple and lock nut (all of these parts are by others)
1 1/4”
sweep 90 deg elbow (by Holovision)
DO NOT GLUE MALE ADAPTER TO PVC PIPE!!
Ground level
1 1/4” 3/4” conduit to gate motor (elbow and conduit by others) Stainless Steel Mounting Bolts (4)
x
1”
reducer (by others)
1” (minimum) conduit to house
NOTE: BE SURE BOTH CONDUITS ARE POINTED IN THE DIRECTION THAT WILL MINIMIZE THE USE OF ELBOWS!
Page 6
This document is property of Holovision, and may not be reproduced without permission.
1 IC only