EZ Option Upgrade Kits - Emlock© 1511, 1513, 1571, 1573
EMLock EZ Kits Field Upgradeable Option Modules for 1511, 1513, 1571, 1573 SDC’s patented EMLock design represents the pinnacle of magnetic lock evolution. The modular EMLock assembly makes them easy to stock, install, upgrade and maintain. Field Upgradeable by Distributors, Installers and Maintenance Staff No need to ever remove a lock from the frame to upgrade or exchange internal components.
EZ-T-10 TIMER INPUT MODULE Modular Kit
EZ-D-10: DOOR POSITION SENSOR Modular Kit
FIELD UPGRADE • Relock Delay Timer • Magnetic Bond Sensor • Door Status Sensors • Anti-Tamper Switch • Holding Force Upgrade • Energy Saver Upgrade
EZ-B-10 MAGNETIC BOND SENSOR Modular Kit
EZ-A: ANTI-TAMPER SWITCH Modular Kit
SECURITY DOOR CONTROLS sdcsecurity.com
[email protected]
sdcsecurity.com
[email protected]
EZ-T-10 TIMER INPUT MODULE Modular Kit Relock Delay Timer, Adjustable 1 to 30 Seconds. Application:
The Timer Input Module delays relocking of access controlled doors to provide persons ample time needed for entry or egress. Momentary interruption of power to the lock input activates the timer module.
Momentary, N.C. Dry Contact required. Contact actuation unlocks the door for 1 – 30 seconds.
SECURITY DOOR CONTROLS SECURITY DOOR CONTROLS © 2007 Security Door Controls
Printed in the U.S.A.
www.sdcsecurity.com
[email protected] [t] 800.413.8783 805.494.0622 [f] 805.494.8861 8801 Avenida Acaso x 3670, Camarillo CA 93011-3670 LIT-Datasheet date qty vendor
EZ Option Upgrade Kits - Emlock© 1511, 1513, 1571, 1573
* Not available for 1513, 1573
EZ-B-10 MAGNETIC BOND SENSOR Modular Kit
While a Door Status Sensor indicates the door is open or closed, SDC’s Magnetic Bond Sensor provides higher security monitoring by indicating the locked / unlocked mode, tampering and low holding force. The use of both the door status and magnetic bond sensor is recommended for high security applications.
Application:
Lock secure status annunciation, mantrap system logic, CCTV camera activation.
Output:
SPDT Dry Contact, 250 mA @ 12/24VDC
SECURITY DOOR CONTROLS sdcsecurity.com
[email protected]
sdcsecurity.com
[email protected]
EZ-D-10: DOOR POSITION SENSOR Modular Kit Indicates the door is open and closed. * Not available for 1513, 1573
Application: Door position status annunciation, anti-tailgating, interlock, mantrap and communicating bathroom system logic. Output: SPDT Dry Contact, 250 mA @ 12/24VDC
EZ-A: ANTI-TAMPER SWITCH - Modular Kit Indicates cover plate removal
Output: SPDT Dry Contact, 3 Amp @ 12/24VDC
SECURITY DOOR CONTROLS SECURITY DOOR CONTROLS © 2007 Security Door Controls
Printed in the U.S.A.
www.sdcsecurity.com
[email protected] [t] 800.413.8783 805.494.0622 [f] 805.494.8861 8801 Avenida Acaso x 3670, Camarillo CA 93011-3670 LIT-Datasheet date qty vendor
EZ Option Upgrade Kits - Emlock© 1511, 1513, 1571, 1573
EZ – 1510W Holding Force Upgrade EZ – 1570W Energy Saver Upgrade All 1511, 1512, 1513, 1571, 1572 and 1573 magnetic coils are field interchangeable without removing the lock from the frame. There is no reason to remove and ship a lock for exchange. Benefits of this interchangeability include: • EZ-1510W Holding Force Upgrade: Exchange 1200 lb coil with 1650 lb holding force coil • EZ-1570W Energy Saver Upgrade: Save on power supply and long term energy costs by exchanging 8.4 Watt,1650 lb coil with 3 Watt, 1200 lb holding force coil • Eliminate labor, shipping costs and time associated with special orders or complete lock removal and replacement.
Applications Distributors with limited stock may exchange coils to fulfill specific special sales needs, i.e. a 1570 with Dark Bronze finish may be upgraded to a 1511 with dark bronze finish and visa versa. Installers may field upgrade to an Energy Saver where power supply capacity is limited or upgrade to higher holding force where 1200 lbs holding force proves inadequate, i.e. psychiatric or rehab center applications.
SECURITY DOOR CONTROLS sdcsecurity.com
[email protected]
sdcsecurity.com
[email protected]
SECURITY DOOR CONTROLS SECURITY DOOR CONTROLS © 2007 Security Door Controls
Printed in the U.S.A.
www.sdcsecurity.com
[email protected] [t] 800.413.8783 805.494.0622 [f] 805.494.8861 8801 Avenida Acaso x 3670, Camarillo CA 93011-3670 LIT-Datasheet date qty vendor
EZ Option Upgrade Kits - Emlock© 1512 / 1572
EMLock EZ Upgrade module to each armature
Kits
Field Upgradeable Option Modules for 1512 and 1572
2 Re-install armature per installation instructions
SDC’s patented EMLock design represents the pinnacle of magnetic lock evolution. The modular EMLock assembly makes them easy to stock, install, upgrade and maintain. Field Upgradeable by Distributors, Installers and Maintenance Staff No need to ever remove a lock from the frame to upgrade or exchange internal components.
FIELD UPGRADE • Relock Delay Timer • Magnetic Bond Sensor • Door Status Sensors • Anti-Tamper Switch • Holding Force Upgrade • Energy Saver Upgrade
EZ-T-10 TIMER INPUT MODULE Modular Kit 5
5 Attach magnetic core
6 Position timer modules + 34 56 78
wire connector to timer module
between posts
T - Timer input module
Connect output wires of timermodule to input terminals 1 and 2 of standards input module. EZ-D-10: DOOR POSITION SENSOR 1 Attach door status module to each armature
Modular Kit
9 Attach cover plate
The Magnetic Bond Sensor should be Cra positioned as shown Position Po below, after step 4.
2
EZ-A: ANTI-TAMPER SWITCH 2 Re-install armature per in Modular Kit
9 Attach cover plate.
SECURITY DOOR CONTROLS sdcsecurity.com
[email protected]
Place anti-tamper switch as shown.
sdcsecurity.com
[email protected]
1 only required
EZ-T-10 TIMER INPUT MODULE Modular Kit Relock Delay Timer, Adjustable 1 to 30 Seconds. 1 only required for double EMLock®. Application:
The Timer Input Module delays relocking of access controlled doors to provide persons ample time needed for entry or egress. Momentary interruption of power to the lock input activates the timer module.
Momentary, N.C. Dry Contact required. Contact actuation unlocks the door for 1 – 30 seconds. Only 1 timer module is required for double Emlocks®. 1 Remove cover plate screws
2 Remove cover plate
3 Carefully lift input
modules from case Standard input module
4 Disconnect magnetic
6 Position timer modules
5 Attach magnetic core
cord wires and remove input module
between posts
wire connector to timer module T - Timer input module
Connect output wires of timermodule to input terminals 1 and 2 of standards input module.
8 T - Timer module wiring
7 Adjustable 1 - 30 Seconds Typical factory setting approximately 5 seconds Turn clockwise to increase time
PC Board Cradle Position Posts
9 Attach cover plate
B Option Connector LOCKED - NO COM UNLOCKED - NC CLOSED - NO D Option COM Door Status Sensor OPEN - NC
B Option Magnetic Bond Sensor
D2
12 or 24 VDC
Access and Egress Control Momentary N.C. Dry Contact Contact actuation unlocks door for 1 - 30 seconds
SECURITY DOOR CONTROLS SECURITY DOOR CONTROLS © 2010 Security Door Controls
Printed in the U.S.A.
LIT-EZ Option Kit Upgrades 12.10
Magnetic Core Connector
www.sdcsecurity.com
[email protected] [t] 800.413.8783 805.494.0622 [f] 805.494.8861 8801 Avenida Acaso x 3670, Camarillo CA 93011-3670
1 Remove cover plate screws.
EZ Option Upgrade Kits - Emlock© 1512 / 1572
Specify 2 for 1512, 1572
EZ-B-10-2 MAGNETIC BOND SENSOR Modular Kit 2 1
While a Door Status Sensor indicates the door is open or closed, SDC’s Magnetic Bond Sensor provides higher security monitoring by indicating the locked / unlocked mode, tampering and low voltage. The use of both the door status and magnetic bond sensor is recommended for high security applications.
ver plate screws. 1 Remove cover plate2 screws. Remove cover plate.
3
2 Remove
Place the Magnetic Bond Sensors at the base of each Magnetic Core.
5
Secure sensor in place with screw as shown.
+ 34 56 78
The Magnetic Bond Sensor should be positioned as shown below, afterPCstep 4. Board
3
from the case bottom.
Place the Magnetic Bond Sensors at the base of each Magnetic Core.
Place the Magnetic Bond Sensors at the base of each Magnetic Core.
Secure sensor in place with screw as 5 shown.
Secure sensor in place with screw as shown.
The Magnetic Bond Sensor should be positioned as shown below, after step 4. PC Board
8 Input module wiring.
Lift input module Li and magnetic coil an from the case. fr The Magnetic Bond Sensor should be positioned as shown magnetic 6 Place magnetic coil firmly below, 6 Place after step 4. coil firmly between core lamination between core lamination as shown. as shown.
8 Input module wiring.9 Attach cover plate.
8 Input module wiring. 9 Attach cover plate. B Option Connector
B Option Connector
LOCKED - NO LOCKED - NO B Option Connect Connect COM COM Magnetic Bond Sensor magnetic UNLOCKED - NC magnetic magnetic UNLOCKED - NC CLOSED - NO bond sensor CLOSED - NO bond sensor bond sensor D Option D Option COM COM Cradle wires Door to the input wires to the input wires toDoor the input Status Sensor Status Sensor OPEN - NC OPEN - NC Position Posts module B Option module B Option module B Option or 24 VDC 12 or 24 VDC connector as shown. connector as shown. connector as12shown. B Option Connect Magnetic Bond Sensor
Cradle Position Posts
Cradle Position Posts
3
Connect magnetic The Magnetic Bond The Magnetic Bond bond sensor Sensor should be Sensor should be wires to the input positioned as shown positioned as shown module B Option after step 4.coil firmly below, after step 4.coil firmly module vertical magnetic magnetic connector shown. con 6 Place magnetic coil firmly below, 6 Place 6 Place 7 Place input module vertically 7 Placeasinput between post at each between post at each between core lamination between core lamination between core lamination side of case. side of case. as shown. as shown. as shown.
odule vertically 7 Place input module vertically between post at each at each side of case.
ond be own p 4.
2 Contacts provided 2-SPDT Dry Contact, 250 mA @ 12/24VDC
+ 34 56 78
5
Output:
4 Remove 2 screw 5
from the case bottom.
Lift input module and magnetic coil from the case.
Lock secure status annunciation, mantrap system logic, CCTV camera activation.
cover plate.
4 Remove 2 screw
Lift input module and magnetic coil from the case. 4 Remove 2 screw from the case bottom.
cover plate.
Application:
2 Remove
cover plate.
2 Remove
Remove cover plate.
Remove cover plate screws.
+ 34 56 78
1 Remove cover plate screws.
9 Attach cover plate.
Magnetic Core Connector
Magnetic Core Connector
B Option Connector LOCKED - NO COM UNLOCKED - NC CLOSED - NO D Option COM Door Status Sensor OPEN - NC
B Option Magnetic Bond Sensor
12 or 24 VDC
SECURITY DOOR CONTROLS sdcsecurity.com
[email protected]
PC Board Cradle Position Posts
sdcsecurity.com
[email protected] 1 Attach door status module to each 1 Attach armature door status module to each armature
EZ-D-10-2: DOOR POSITION SENSOR Modular Kit
1 Attach odule to each armature door status module to each armature
2 Re-install armature per installation 2 Re-install instructions armature per installation instructions
3 Input module wiring. B Option Connector LOCKED - NO COM UNLOCKED - NC CLOSED - NO D Option COM Door Status Sensor OPEN - NC
B Option Magnetic Bond Sensor
Indicates the door is open and closed.
Application: er installation instructions 3 Input module wiring.
ED - NO COM ED - NC D - NO COM EN - NC
2 Re-install armature per installation 2 Re-install instructions armature per install
Door position status annunciation, B Option anti-tailgating, interlock, Connector mantrap module wiring. 3 Input and communicating bathroom LOCKED - NO B Option COM Magnetic Bond Sensor system logic. UNLOCKED - NC B Option Connector
D Option Door Status Sensor LOCKED - NO B Option COM 12 or 24 VDC Magnetic Bond Sensor UNLOCKED - NC CLOSED - NO D Option COM Door Status Sensor OPEN - NC
12 or 24 VDC
3 Input module wiring.
4 Annunciation
4 Annunciation
B Option Connector
4 Annunciation
LOCKED - NO COM UNLOCKED - NC CLOSED - NO D Option COM Door Status Sensor OPEN - NC
B Option Magnetic Bond Sensor
CLOSED - NO COM OPEN - NC
Output: 2 Modules provided SPDT Dry Contact, 250 mA @ 12/24VDC
4 Annunciation
12 or 24 VDC
Magnetic Core Connector
Locked
Magnetic Core Connector
Unlocked
Locked
12 or 24 VDC
1 Remove cover plate Magnetic Core Connector
1 Remove cover plate Locked
Magnetic Core Connector
1 Remove cover plate
2 Unlocked
2
2
Locked
Unlocked
3 Anti-tamper wiring
2
1 only required
EZ-A: ANTI-TAMPER SWITCH - Modular Kit 3 Anti-tamper wiring
Indicates cover plate removal
3 Anti-tamper wiring
3 Anti-tamper wiring
4 Replace cover plate
4 Replace cover plate
Output: 4 Replace cover plate SPDT Dry
Com No NC Com No NC
4 Replace cover plate
Place anti-tamper switch as shown.Place anti-tamper Cover depresses switch Cover depresses Contact, 3 Amp @ 12/24VDC arm when mounted arm when mounte
Place anti-tamper switch as shown.Place anti-tamper switch as shown. Cover depresses switch Com Cover depresses switch No arm when mounted arm when mounted NC
Com No NC
ti-tamper switch as shown. presses switch n mounted
SECURITY DOOR CONTROLS SECURITY DOOR CONTROLS © 2010 Security Door Controls
Printed in the U.S.A.
LIT-EZ Option Kit Upgrades 12.10
www.sdcsecurity.com
[email protected] [t] 800.413.8783 805.494.0622 [f] 805.494.8861 8801 Avenida Acaso x 3670, Camarillo CA 93011-3670
1 Remove cover plate screws.
EZ Option Upgrade Kits - Emlock© 1512 / 1572
Specify 2 for 1512, 1572
EZ – 1510W-2 Holding Force Upgrade EZ – 1570W-2 Energy Saver Upgrade All 1511, 1512, 1513, 11571, 1572 and 1573 magnetic coils are field interchangeable without removing lock from the frame. There is no reason 2 the 2 Remove Remove cover plate screws.1 Remove cover plate screws. Remove to remove and ship a lock for exchange. cover plate. cover plate. Benefits of this interchangeability include:
Applications Distributors with limited stock may exchange coils to fulfill specific special sales needs, i.e. a 1570 with Dark Bronze finish may be upgraded to a 1511 with dark bronze finish and visa versa.
• EZ-1510W Holding Force Upgrade: Exchange 1200 lb coil with 1650 lb holding force coil • EZ-1570W Energy Saver Upgrade: Save on power supply and long term energy costs by exchanging 8.4 Watt,1650 lb coil with 3 Watt, 1200 lb holding force coil
Installers may field upgrade to an Energy Saver where power supply capacity is limited or upgrade to higher holding force where 1200 lbs holding force proves inadequate, i.e. psychiatric or rehab center applications.
ver plate screws.1 Remove cover plate2screws. Remove cover plate.
3 Lift input modules
5 Connect
upgrade coils
6 Place magnetic coil
5 Connect upgrade coils
7 Place input modules
firmly between core lamination as shown.
6 Place magnetic coil firmly between core lamination as shown. 8 Input module wiring.
vertically between posts at each side of case.
+ 34 56 78
PC Board Cradle Position Posts
firmly between core lamination as shown.
6 Place magnetic coil 7 Place input modules firmly between core vertically between posts lamination as shown. at each side of case. 8 Input module wiring. 9 Attach cover plate.
B Option Connector
B Option Magnetic Bond Sensor
PC Board Cradle Position Posts
8 Input module wiring.9 Attach cover plate.
3 Lift input modules
6 Place magnetic coil
5 Connect
upgrade coils
+ 34 56 78
remore coils
odules ween posts f case.
and magnetic coils from 4 Disconnect and 5 the Connect case. remore coils upgrade coils
remore coils
4 Disconnect and
3 Lift input modules
cover plate.
4 Disconnect and
and magnetic coils from the case.
ils
2 Remove
cover plate.
+ 34 56 78
ules
2 Remove
+ 34 56 78
• Eliminate labor, shipping costs and time associated with special orders or complete lock removal and replacement.
LOCKED - NO COM
LOCKED - NO COM UNLOCKED - NC CLOSED - NO D Option COM Door Status Sensor OPEN - NC 12 or 24 VDC
6 Place magnetic coil firmly between core lamination as shown.
Connect magnetic bond sensor wires to the input module B Option connector asinput shown. modules 7 Place vertically between posts at each side of case.
B Option Connector
B Option Magnetic Bond Sensor
LOCKED - NO COM
Connect UNLOCKED - NC Connect UNLOCKED - NC Connect CLOSED - NO CLOSED - NO magnetic bond magnetic bond magnetic bond D Option D Option COM COM Door Status Door Status Sensor sensor wires to the sensor wires to Sensor the sensor wires to the OPEN - NC OPEN - NC Cradle input module B input module B input module B Position Posts 12 or 24 VDC 12 or 24 VDC Option connector Option connector Option connector as shown. as shown. as shown. Magnetic Core Connector
Magnetic Core Connector
9 Attach cover plate.
B Option Connector
B Option Magnetic Bond Sensor
and magnetic coils from the case.
SECURITY DOOR CONTROLS sdcsecurity.com
[email protected]
PC Board Cradle Position Posts
se
sdcsecurity.com
[email protected]
SECURITY DOOR CONTROLS SECURITY DOOR CONTROLS © 2010 Security Door Controls
Printed in the U.S.A.
LIT-EZ Option Kit Upgrades 12.10
www.sdcsecurity.com
[email protected] [t] 800.413.8783 805.494.0622 [f] 805.494.8861 8801 Avenida Acaso x 3670, Camarillo CA 93011-3670
EZ Option Upgrade Kits - Emlock© 1581
EMLock EZ Kits Field Upgradeable Option Modules SDC’s patented EMLock design represents the pinnacle of magnetic lock evolution. The modular EMLock assembly makes them easy to stock, install, upgrade and maintain. Field Upgradeable by Distributors, Installers and Maintenance Staff No need to ever remove a lock from the frame to upgrade or exchange internal components.
EZ-D-80: DOOR POSITION SENSOR Modular Kit
11 Attach Attach door door status status module module to to armature armature
FIELD UPGRADE • Magnetic Bond Sensor • Door Status Sensors • Tamper
2 2Install Install lock per installation instructions lock per installation instructions
In 3 3Inpu
Magne Mag
Indicates the door is open and closed. Application: 2 2Install Install lock lock per per installation installation instructions instructions
Door position status annunciation, anti-tailgating, interlock, mantrap and communicating bathroom system logic.
Input module module wiring. wiring. 3 3Input 11 Remove cover plate Remove cover plate B Option B Option NO NO COM COM
Magnetic Magnetic Bond Bond Sensor Sensor
Position cover depresses switch Position cover depresses switch arm when mounted arm when mounted
NOT NOT USED USED
{{
NO NO
DPSDPS
Output: SPDT Dry Contact, 250 mA @ 12/24VDC
Annunciation 4 4Annunciation 22 Place anti-tamper switch shown Place anti-tamper switch asas shown
CO CO NC NC
POWER POWER
Locked Locked
Magnetic Magnetic Core Core Connector Connector
22
Place Place anti-tamper anti-tamper switch switch asas shown shown Position Position cover cover depresses depresses switch switch arm arm when when mounted mounted
4 4Replace Replace cover cover plate plate
3 3Anti-tamper Anti-tamper wiring wiring
Com Com NoNo NCNC
SECURITY DOOR CONTROLS sdcsecurity.com
[email protected]
Unlocked Unlocked
3 3Anti A
st
sdcsecurity.com
[email protected]
EZ-B-80 MAGNETIC BOND SENSOR Modular Kit Application:
Lock secure status annunciation, mantrap system logic, CCTV camera activation.
Output:
SPDT Dry Contact, 250 mA @ 12/24VDC
1 1Remove cover plate screws. Remove cover plate screws. 2 2 Remove 2Remove Remove cover cover cover plate. plate. plate.
1 1Remove 1Remove Remove cover cover cover plate plate plate screws. screws. screws.
2 2Remove cover plate. Remove cover plate. 3 3 Lift 3Lift Lift input input input module module module and and and magnetic magnetic magnetic coil coil coil from from from the the the case. case. case.
3 3Lift input Lift inpu Remo 1 4 4Remove 4Remove
and magn and mag from from from the the tc from the c from the bottom. bottom. bottom
+ 34 56
While a Door Status Sensor indicates the door is open or closed, SDC’s Magnetic Bond Sensor provides higher security monitoring by indicating the locked / unlocked mode, tampering and low holding force. The use of both the door status and magnetic bond sensor is recommended for high security applications.
+ 34 56 78
Place Place Place the th Magnetic Magneti Magne Sensor Sensor Senso at base base base ofofth o Magnetic Magneti Magne
Secure Secure Secur se ininplace in place plac w screw screw screw asa shown. shown. shown
should bebe positioned asas should positioned atat each at each each side side side ofofcase. of case. case. bottom. bottom. shown below, after step 4. 4. shown below, after step PCPC Board PC Board Board
Place the Magnetic Bond Sensor at the base of the Magnetic Core.
Place Place thethe Cradle Cradle Cradle Magnetic Bond Magnetic Bond Position Position Position Posts Posts Posts Sensor Sensor at at thethe base base of of thethe Magnetic Core. Magnetic Core.
Secure sensor in place with screw as shown.
Secure sensor Secure sensor place with in in place with screw screw asas shown. shown.
Input module wiring. 8 98Input module wiring. Attach cover plate. B Option B Option Magnetic Bond Sensor Magnetic Bond Sensor
+ 34 56
Remove 1 Bond screwSensor 4 Remove 1 screw 57 754The Magnetic The Magnetic Bond Sensor 7Place Place Place input input input module module module vertically vertically vertically between between between post post post from the case from the case
from the case should should should be be positioned be positioned positioned asasas from the case. from the case. bottom. shown shown shown below, below, below, after after after step step step 4.4. 4.
7 7Place input module vertically between post input module vertically between post 8 8 Input 8Place Input Input module module module wiring. wiring. wiring. at at each side ofof case. each side case.
B Option B Option B Option PC Board PC Board Magnetic Magnetic Magnetic Bond Bond Bond Sensor Sensor Sensor
BO Magnetic Bond S Magnetic Bon
NONONO COM COM COM
Cradle Cradle Position Posts Position Posts NOT NOT USED NOT USED USED
{{ {
NONONO
DPS DPS DPS
COCOCO NCNCNC
P
POWER POWER POWER
Magnetic Magnetic Magnetic Core Core Core Connector Connector Connector
9 9 Attach Attach cover plate. cover plate.
NO NO COM COM
NOT USED NOT USED
{{
NO NO
DPSDPS
CO CO NC NC
POWER POWER
Magnetic Core Magnetic Core Connector Connector
SECURITY DOOR CONTROLS SECURITY DOOR CONTROLS © 2007 Security Door Controls
Printed in the U.S.A.
8 8Input mod m 9 9 Attach 9Input Attach Attac co
+ 34 56
3 43Lift Lift input input module Remove 1 module screw 5 5 The 5and The The Magnetic Magnetic Magnetic Bond Bond Bond Sensor Sensor Sensor and magnetic coil magnetic coil
www.sdcsecurity.com
[email protected] [t] 800.413.8783 805.494.0622 [f] 805.494.8861 8801 Avenida Acaso x 3670, Camarillo CA 93011-3670 LIT-Datasheet date qty vendor
EZ Option Upgrade Kits - Emlock© 1582
EMLock EZ Kits Field Upgradeable Option Modules SDC’s patented EMLock design represents the pinnacle of magnetic lock evolution. The modular EMLock assembly makes them easy to stock, install, upgrade and maintain.
FIELD UPGRADE • Magnetic Bond Sensor • Door Status Sensors
Field Upgradeable by Distributors, Installers and Maintenance Staff No need to ever remove a lock from the frame to upgrade or exchange internal components.
Specify 2 for 1582
11 Attach Attach door door status status module module to to armature armature
2 2Install Install lock per installation instructions lock per installation instructions
EZ-D-80: DOOR POSITION SENSOR Modular Kit
In 3 3Inpu
Door Door Sta
12 o 1
Indicates the door is open and closed. Application: 2 2Install Install lock lock per per installation installation instructions instructions
Door position status annunciation, anti-tailgating, interlock, mantrap and communicating bathroom system logic. Output:
Input module module wiring. wiring. 3 3Input 11 Remove cover plate Remove cover plate
Annunciation 4 4Annunciation 22 Place anti-tamper switch shown Place anti-tamper switch asas shown Position cover depresses switch Position cover depresses switch arm when mounted arm when mounted
NOT NOT USED USED CLOSED CLOSED - NO - NO D Option D Option COM COM Door Door Status Status Sensor Sensor OPEN OPEN - NC - NC 12 or 12 24 or VDC 24 VDC
SPDT Dry Contact, 250 mA @ 12/24VDC Magnetic Magnetic Core Core Connector Connector
22
Place Place anti-tamper anti-tamper switch switch asas shown shown Position Position cover cover depresses depresses switch switch arm arm when when mounted mounted
Locked Locked
4 4Replace Replace cover cover plate plate
3 3Anti-tamper Anti-tamper wiring wiring
Com Com NoNo NCNC
SECURITY DOOR CONTROLS sdcsecurity.com
[email protected]
Unlocked Unlocked
3 3Anti A
sdcsecurity.com
[email protected]
Specify 2 for 1582
EZ-B-80 MAGNETIC BOND SENSOR Modular Kit
1 Remove rews. ove cover plate screws.cover plate screws.
2 Remove cover plate. 2 Remove cover plate. 2 Remove cover plate.
3
4 Remove 1 screw 4 Remove 1 screw from the case bottom.
Lock secure status annunciation, 2 Remove 2 Remove cover plate. mantrap system logic, cover plate. CCTV camera activation. SPDT Dry Contact, 250 mA @ 12/24VDC 3
3
3
+ 34 56
While a Door Status Sensor indicates the door is open Application: 1provides or closed, SDC’s Magnetic1 Bond Sensor higher Remove cover plate screws. Remove cover plate screws. security monitoring by indicating the locked / unlocked mode, tampering and low holding force. The use of both the door status and magnetic bond sensor is Output: recommended for high security applications.
from the case bottom.
Lift input module Lift input module L and magnetic coil and magnetic coil a from the case. from the case. f
6 Place input module 6 Place vertically inputbetween module post vertically between post at each side of case. at each side of case. PC Board
PC Board
Cradle Position Posts
Cradle Position Posts
++ 3344 5566
Place the Place the Magnetic Bond Magnetic Bond Sensor at the Sensor at the base of the base of the Magnetic Core. Magnetic Core. 5 The Magnetic Bond 5 The Sensor should 4 Remove 1 screw Magnetic Bond Sensor should Secure sensor Secure sensor as shown be positioned as shown from the case be positioned placeafter withstep 4.in place with module below, after step 4.in bottom.Lift input module Lift input below, screw as screw as and magnetic coil and magnetic coil shown. shown. from the case. from the case. Place the Magnetic Bond Sensor at the base of the Magnetic Core.
+ 34 56 78
6 Place input module 6 Place 6 Place 7 Input module wiring. 7 Input module wiring. 7 Input module wiring. 5 The Magnetic sor should Bond Sensor Magnetic should Bond Sensor should vertically inputbetween module vertically post inputbetween module vertically post between post Secure sensoras shown ositioned as shown be positioned at each side of case. at each side of case. at each side of case. NO - SPST NO - SPST NO - SPST B Option B Option B Option in place with w, after step 4.below, after step 4. PC Board PC Board PC Board Magnetic Bond Sensor Magnetic Bond Sensor Magnetic Bond Sensor screw as Cradle Cradle Cradle shown. Position Posts
7 Input module wiring. module wiring.
B Option tic Bond Sensor
D Option atus Sensor
r 24 VDC
Position Posts
8 Attach cover plate. 8 Attach cover plate.
D Option Door Status Sensor
NOT USED
NOT USED
NOT USED
CLOSED - NO
CLOSED - NO
CLOSED - NO
D Option COM Door Status Sensor OPEN - NC
D Option COM Door Status Sensor OPEN - NC
COM OPEN - NC
NO - SPST
NO - SPST B Option Magnetic Bond Sensor
12 or 24 VDC
NOT USED
NOT USED
CLOSED - NO
CLOSED - NO
D Option COM Door Status Sensor OPEN - NC
Position Posts
12 or 24 VDC
12 or 24 VDC
Magnetic Core Connector
COM OPEN - NC
8 Attach cover plate. 12 or 24 VDC
Magnetic Core Connector
Magnetic Core Connector
SECURITY DOOR CONTROLS SECURITY DOOR CONTROLS © 2007 Security Door Controls
Printed in the U.S.A.
www.sdcsecurity.com
[email protected] [t] 800.413.8783 805.494.0622 [f] 805.494.8861 8801 Avenida Acaso x 3670, Camarillo CA 93011-3670 LIT-Datasheet date qty vendor
Magnetic Core Connector
