AP.12B.07.0076A.de
Specification
Part No.
AP.12B.07.0076A.de
Product Name
1.8V/20dB/76mm/ I-PEX
Feature
Ultra Miniature GPS active patch High performance Ultra low power consumption RoHS compliant
SPE-12-8-070/B/SS |
page 1 of 5
1. Introduction This miniaturised GPS Active Antenna module combines a tiny 12mm squared ceramic patch antenna with a two stage
20dB low noise amplifier. It is available as a ‘plug and play’ format for onboard integration with GPS receiver modules via
ultra thin coaxial cable and connector from IPEX.
2. Specification 2.1 Patch Antenna Parameter
Specification
Frequency
1575.42 ± 1.023MHz
Antenna Gain
Typ -1.5 dBic @ Zenith(13.4mm*13.4mm Ground Plane)
Impedance
50Ω
Polarization
RHCP
Axial Ratio
Max 4.0dB @ Zenith
Patch Dimension
12mm x 12mm x 3.5mm
2.2 LNA Parameter
Specification
Frequency
1575.42 ± 1.023MHz
Gain
Min. 18dB Typ. 20dB @ 25°C ± 5°C
Noise Figure
Typ. 1.0dB @ 25°C ± 5°C Max 1.5dB @ 85°C
Output VSWR
2.0 Max
SPE-12-8-070/B/SS |
page 2 of 5
2. Specification 2.3 Cable* & Connector Parameter
Specification
RF Cable
Coaxial Cable Ø 1.13 ± 0.1mm, length 46 ± 2.5mm
Connector
IPEX MHFI (U.FL)
2.4 Total Specification Parameter
Specification
Frequency
1575.42 ± 1.023MHz
Gain
18.5 ± 4dBic @ 90°
Output Impedance
50Ω
Polarization
RHCP
Output VSWR
Max 2.0
Input Voltage
Min. 1.5V
Power Consumption
At 1.8V Typ. 3.3mA,
Typ. 1.8V
Max. 3.3V Max. 5mA
SPE-12-8-070/B/SS |
page 3 of 5
3. Technical Drawing A
IPEX MHF1
Top
Bottom
Sandy
Sandy
2012/02/09
2012/02/09
IPEX MHF1
Top "A"
"A"
Side
ALL Initial Design A ALL Initial Design
Side
Bottom
Name
NOTES: Name 1.Soldered area 1 AP.12B Patch(12*12*4mm) 1 AP.12B Patch(12*12*4mm) NOTES: 2.Shielding case area NOTE: Name P/N 1.Soldered area 3.Double sided adhesive area. 2 21.131.13 Coaxial Cable 1. Soldered area 1 AP.12B AP.12B Patch(12*12*4mm) Coaxial Cable 2.Shielding case area 4.All material must be RoHS compliant. The 3.Double sided adhesive area.connector orientation has a fixed 2. Shielding case 5. area 3 3IPEXIPEX MHF1 Connector 2 as OD.113.CM MHF1 Connector 1.13 position to the antenna per Coaxial drawing. Cable 4.All material must be RoHS 3. All material must becompliant. RoHS compliant. 5.The connector orientation has a fixed 4 Shielding Case 4 Shielding Case IPEX MHF1 Connector 4.position The connector orientation has a3 fixed to the antenna as per drawing. IPEX.MHFI.113
position to the antenna as per drawing. 4
P/N
Material
Finish
AP.12B
Ceramic
Clear
OD.113.CM Ceramic OD.113.CM
FEP FEPClear
Gray 1
11
Brass Brass Gray
Gold 1Gold
11
Tin (SPTE) Tin Gold (SPTE)
Tin Plated Plated 1Tin
11
NITTO 5015 NITTO Tin 5015 Plated
White Liner 1WhiteLiner
11
FR4White 0.5t Liner FR4 0.5t
Green 1Green
11
P/N
AP.12BMaterial
IPEX.MHFI.113 FEP
IPEX.MHFI.113
Brass
Sided Double SidedAdhesive Adhesive Shielding 5Case5Double
Tin (SPTE)
5
6 Adhesive PCB 6AP.12B AP.12B PCB Double Sided
NITTO 5015
6
AP.12B PCB
FR4 0.5t
Material
Ceramic Finish
Green
Finish
1
1
Clear QTY Gray
1
TW Design Centre This drawing and its inherent design concepts are property of Taoglas. Not to be copied or given to third parties without the written consent of Taoglas.
SPE-12-8-070/B/SS |
TW Design Centre This drawing and its inherent design concepts are property of Taoglas. Not to be copied or given to third parties without the written consent of Taoglas.
QTY
QTY
page 4 of 5
Taoglas makes no warranties based on the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and
product descriptions at any time without notice. Taoglas reserves all rights to this document and the information
contained herein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. Copyright © 2012, Taoglas Ltd.
SPE-12-8-070/B/SS |
page 5 of 5
