Model 561 Dynamic Microphone User Guide 5. Slide the cable all the way through the gooseneck. 6. Thread the microphone firmly onto the gooseneck. 7. Connect the cable wires to the amplifier, mixer, or radio transmitter via screw terminals, an XLR connector, or a 1/4-inch phone plug. See Figure 1 and Table 1 below for wiring information. 8. Lock the microphone in place by tightening the setscrew over the mounting threads. The setscrew in the nameplate can be tightened to secure the grille. NOTE: Use Shure A95 Line Matching Transformers to match a low impedance (300 :) microphone line to a high impedance amplifier or mixer input. The A95 is available with various input/output connectors.
CONNECTOR WIRING
MODEL 561 OMNIDIRECTIONAL DYNAMIC MICROPHONE The Shure Model 561 is an omnidirectional, low-impedance dynamic microphone designed for use on a stand or flexible gooseneck. Its smooth frequency response is tailored for optimum speech intelligibility, making it ideal for language labs, paging applications, and base station communications. The 561 is also suitable for use as a talk-back or cuing microphone in TV, film, and recording studios.
The 561 may be wired for either balanced or unbalanced operation. For balanced operation, the WHITE wire is connected to the positive audio input, the BLACK wire is connected to the negative audio input, and the SHIELD is connected to chassis ground. Refer to Figure 1 and Table 1 below. For unbalanced operation, the WHITE wire is connected to the audio input, the BLACK wire is connected to audio ground, and the SHIELD is connected to chassis ground. CARTRIDGE
CABLE WHITE BLACK SHIELD
CODED TERMINAL
FEATURES • • • • • • •
Frequency response tailored for speech applications, with bass rolloff and mid-range “presence” rise Omnidirectional pickup pattern Low impedance; long lengths of cable can be used without affecting microphone response or level Shock-mounted cartridge for reduced stand and handling noise Rugged die-cast aluminum construction Lockable stainless steel mesh grille Optional gooseneck and mounting flange
INTERNAL CONNECTIONS FIGURE 1
TABLE 1. CABLE-TO-CONNECTOR WIRING INPUT TYPE
BALANCED
UNBALANCED
GOOSENECK MOUNTING AND INSTALLATION
WIRE COLOR
FUNCTION
XLR CONNECTOR
1/4 INCH PHONE PLUG
WHITE
AUDIO +
PIN 2
TIP
BLACK
AUDIO -
PIN 3
RING
SHIELD
CHASSIS GROUND
PIN 1
SLEEVE
WHITE
AUDIO
--
TIP
BLACK
AUDIO GROUND
--
SLEEVE
SHIELD
CHASSIS GROUND
--
SLEEVE
1. If necessary, drill a hole approximately 7 mm (1/4 in.) in diameter through the mounting surface. 2. Place the flange over the hole in the mounting surface and secure it with three screws. 3. Thread the supplied hexnut all the way down on the flange. 4. Thread the gooseneck tightly onto the flange. Back the hexnut up against the gooseneck. Use a wrench to tighten the nut firmly against the bottom of the gooseneck.
©2005, Shure Incorporated 27C2057 (Rev. 7)
Printed in U.S.A.
SPECIFICATIONS
Net Weight 142 grams (5 oz.) Packaged Weight 255 grams (9 oz.) Certification Conforms to European Union directives, eligible to bear CE marking; meets European Union EMC Immunity Requirements (EN 50 082-1, 1992).
Type Dynamic Frequency Response 40 to 10,000 Hz (See Figure 2)
+10
dB
FURNISHED ACCESSORIES 0
Allen wrench (No. 4)......................................................... 80A67
–10
20
OPTIONAL ACCESSORIES 50
100
2
3 4 5 6 7 89 1000
2
Gooseneck, 45.7 cm (18 in.) ................................................G18 Gooseneck, 45.7 cm (18 in.), Side Vent ........................... G18A Gooseneck, 30.5 cm (12 in.) ................................................G12 Gooseneck, 15.25 cm (6 in.), Side Vent ............................. G6A Mounting Flange................................................................... A12 Heavy-Duty Mounting Flange..........................................A13HD
3 4 5 6 7 89 10000 20000
Hz
TYPICAL FREQUENCY RESPONSE FIGURE 2 Polar Pattern Omnidirectional Impedance Rated at 150 Ohms (200 Ohms actual). Designed for connection to inputs rated at 19 to 300 Ohms. Output Level (at 1,000 Hz) Open Circuit Voltage . . . . . . –57.5 dBV/Pa (1.33 mV) (1 Pa = 94 dB SPL) Polarity Positive pressure on diaphragm produces positive voltage on the white cable lead relative to the blacklead. Cable 1.2 m (4 ft.) two-conductor, shielded, unterminated Stand Thread Suitable for mounting on stand or gooseneck with 5/8”–27 thread. Case Silver and black aluminum with stainless steel grille Dimensions See Figure 3
REPLACEMENT PARTS Cartridge...............................................................................R50 Screen and Grille Assembly ............................................RK85G For additional service or parts information, please contact the Shure Service Department at 1-800-516-2525. Outside the United States, please contact your authorized Shure Service Center.
ARCHITECTS' SPECIFICATION The microphone shall be a moving coil (dynamic) type with a frequency response of 40 to 10,000 Hz. It shall have an omnidirectional polar characteristic and a low impedance rated at 150 Ohms for connection to inputs rated 19 to 300 Ohms. The microphone output level shall be –57.5 dBV/Pa. It shall be equipped with a non-detachable 1.2 m (4 ft.) cable. The microphone shall be threaded for mounting on a stand or gooseneck with a 5/8"–27 thread. The overall dimensions of the microphone shall be 67.1 mm (2–21/32 in.) in length and 34.5 mm (1–3/8 in.) in diameter. The microphone shall be the Shure Model 561 or equivalent.
67.1 mm (2–21/32 in.)
34.5 mm DIA. (1–3/8 in.)
5/8 in.–27 thread Nameplate #4–40 Allen setscrews
OVERALL DIMENSIONS FIGURE 3
SHURE Incorporated http://www.shure.com United States, Canada, Latin America, Caribbean: 5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A. Phone: 847-600-2000 U.S. Fax: 847-600-1212 Intl Fax: 847-600-6446 Europe, Middle East, Africa: Shure Europe GmbH, Phone: 49-7131-72140 Fax: 49-7131-721414 Asia, Pacific: Shure Asia Limited, Phone: 852-2893-4290 Fax: 852-2893-4055
2
